we have lots of items in stock，if you need more items，please contact us
1.Description:
The controller only controls the speed of the four line standard specification Intel PWM fan, do not turn off the fan. With full digital control, accurate temperature setting and precise control. It integrates manual speed regulation and automatic temperature control and speed regulation function. Manual speed control from 10%-100%, each 5% is a gear. Automatic temperature control speed from 30 degrees Celsius, there are 49 kinds of temperature zone combination. It supports three line to four line control, setting parameters automatically save.
 
2.Parameters:

Parameter

Value

Operating voltage

DC12V can work in 8-18V range

Fan interface

2510-4P lacks 1 bends (special interface for computer 4P fan

Consumption current

No more than 20mA

Fan current

Less than 3A

Drive output range

10% -100

Operating temperature

-10 Celsius to 60 Celsius

Temperature probe parameters

NTC 50K B=3950

Probe temperature

Small black head 120 degrees
Ring probe 110 Celsius

Board size

34mm*19mm*11mm (excluding extended interface)
Fan interface extends 8mm

Setting parameters default factory

Low speed 20%.
Acceleration temperature 30 Celsius.
Acceleration width 5 Celsius.
Do not shut down the output.

At this temperature setting, holding the probe with the palm of the hand will accelerate in a few minutes. If the probe is clamped into the armpit, it will reach full speed in 2 minutes.

  1. Components:

    1>. Input line: red black power line is only welding 12V positive and negative power cord, as a

    general use. The three wire connector is equipped with a 2510-3P plug, which is used to

    measure the speed of some main board three wire fan ports. Large 4P interface facilitates

    power acquisition from chassis.

       2>. temperature probe: small black line’s head is short, low heat capacity. It is suitable for

    testing narrow space and air temperature, and the response is relatively fast. The ring probe

    is enclosed inside a ring metal head with a diameter of 4.2mm. It is suitable for mounting on

    the radiator or other heating object surface with screws.
  2.  Manual automatic integration control:

    1>. Manual control without temperature probe. Click / double-click (double-click speed not too

     fast) button up / down gear. Each shift continues after 20 seconds, and the gear is

     automatically stored. The No. 2 indicator flashes rapidly in 20 seconds (when the temperature

     control is invalid). When the flash is stopped, it indicates that the file has been stored. The 3 /

     1 indicator light is always on when you can not continue to increase / not continue to reduce

     the position.

    2>. When the temperature probe is installed, the manual speed is used as the initial low

    speed (bottom line speed). When the temperature exceeds the accelerating temperature, the

     fan speed accelerates smoothly with the increase of temperature.

    When the temperature reaches and exceeds the sum of the acceleration temperature and the

     acceleration width (full speed temperature), the fan runs at full speed.

    Set the acceleration temperature and acceleration width parameters as shown in the

    schematic diagram below. The number 123 represents the indicator light on the board (red)

    and the (white) state is displayed in binary order:
  3. Example instruction:

    Bottom line 20%, acceleration temperature 35, acceleration width 15.

    When the probe temperature is lower than 35 degrees centigrade, the output signal is always

    20%. When the probe temperature is higher than 35 degrees, the controller can increase the

     output signal smoothly according to the temperature rise, and the fan accelerates. When the

     probe temperature reaches or exceeds 50 (35+15), the controller outputs the full speed

    signal and the fan runs at full speed.

        According to the specific performance of the fan, the actual speed of the fan will be somewhat different.
  4. Setting method:

    P.S. The controller has supported the control of the reverse timing fan.

    First, power off and remove the fan. Press the set button to electrify the controller. Keep the

    settings button always hold (about 3 seconds) until the three lights turn into double flash state

     and then release the button.

        The indicator lamp turns into a single light, which represents the entry mode setting state.

        The controller is divided into three kinds of working modes, corresponding to 1, 2, 3

    indicator light double flashing, through short press button switch, set the long, press the button

     to save and exit the set mode and automatically back to normal working state. The three

    working modes are as follows:

        1>. conventional PWM fan control mode (default mode). This mode is used for the four wire

     fan control of the standard Intel specification.

        2>. conventional reverse sequence PWM fan control mode. This mode is used in most

    reverse timing four wire fan control. When the fan is in normal mode control, the speed

    change is opposite, and the control line is connected to the negative pole at full speed.

        3>. reverse sequence fan 80% control mode. This mode is used in a very rare type of

    reverse timing fan. When the fan is in conventional mode control, the speed change is

    opposite, and the control line is not turned when the negative electrode is connected.
  5. Package included: 1pc DC 12V PWM Fan Temperature Controller 4-Wire Speed Governor Board

EBAY Managed Payment. But we only Accept your Ebay Address, please Make sure it's 100% right.
Payment must be received in 5 business days of auction closing.
Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.

1. We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2. Orders will be processed instantly and dispatched within 1-3 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3. All package need to wait 30 days,Please take care it.Less than 30 days,we can't take a refund.

  • All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
  • If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
  • If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.

We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.

We are professional Business & Industrial DIY Module part store. Follow and save our store,We will provide the best service and high quality-low price items for you.Save more