Please Note:
This item located in Czech Republic and only shipped to European countries,
If you need to return the item for some reasons, please contact us via eBay message firstly to get the RMA#,and return address instead of sending iit back directly without permission,thank you!
GODIAG GT100 OBDII Protocol Detector OBD2 Breakout Box E-C-U Connector What is GODIAG GT100? More than a simple OBD-II breakout box, the GODIAG GT100 is an OBD-II breakout box designed specifically for off-board module and key progarmming and features a display readout for both voltage and current draw through the box. Highlights for Godiag GT100: It is the latest testing platform for OBDII protocol communication detection and E-C-U maintenance/diagnosis /progarmming /coding. It can convert the car OBD2 interface into 16 pin for signal detection. Able to connect the single modules or multiple modules of the vehicle. It can be connected with any diagnostic tool to tell whether the car communication is good or not. Can work with most device to do test, will make your operation much easier , such as xhorse vvdi2, Autel Scanner, Launch Scanner, Vident Scanner, and so on. It can also supply power to the car when you change the battery to avoid the vehicle control module data being lost,automatically lo*cked,the key remote control fails and the fault light turns on. Can support all key lost, activate the meter and wake up the anti-theft module. (1) for Porsche, V-W 4th generation smart key &5th generation card key (models such as: new A6L Touareg A4 Q5 A7), use GT100 short the banana PIN 16----PIN 1, After the instrument is on, the key matching tool connects to GT100+ female Head for data collection. Some vehicle instruments are not bright, but data can also be collected, for example: A6L Q7. (2) Can replace the engine E-C-U for Toyota; and Support onnect short-circuit PIN13-PIN4 with Key Progarmmer when do all key lost for Toyota. (3) For Mitsubishi all key lost matching or all key lost for remote control key, need to set OBDII short-circuit PIN1-PIN4. With BMW CAS4 & CAS4+ Test Platform and BMW FEM/BDC test platform(not included),GT100 can work with Xhorse VVDI2/Lonsdor K518/CGDI/Autel im608 to Support Off-site Key progarmming/All Keys Lost/ Add New Key. - By connecting the vehicle and diagnostic tool via OBDII, Godiag GT100's LED will indicate whether the OBDII diagnostic interface has a good communication with the car - Monitor the voltage of vehicle OBDII interface and display it in real time. If it is less than 11V, please stop the diagnosis and progarmming to avoid the vehicle being unable to start/data loss/module lo*cked. 1. Manufacturer custom 9. Manufacturer custom GODIAG GT100 OBD2 Breakout Box Functions: 1. OBDII Protocol Detector & communication detection 1) Connect GODIAG GT100 to the OBDII diagnostic port of the car. 2) When the device displays the voltage, turn on the power switch of GODIAG GT100. 3) Then connect to the diagnostic tool, when the tool is communicating with the car, the LED indicator of corresponding protocol will light up or flash. ( If the CAN protocol is detected, it will have the maximum brightness. When the communication is successful, the corresponding CAN-H and CAN-L will dim or twinkling weakly) GODIAG GT100, connected to a single E-C-U module, is convenient for a user to do the single-module diagnosis and progarmming. 1) Connect the E-C-U with the color jumpers. (If the E-C-U is CAN protocol, please check whether you will need to connect a 120 ohm resistor.) 2) The Godiag GT100 can be powered by connecting to the OBDII diagnostic interface of car, or by an AC power adapter. 3) To diagnose and progarm for a single E-C-U by connecting the diagnostic tool or E-C-U Progarmmer. Extend the car's OBDII 16pin interface to tell you whether the OBDII interface connection is good or not, which is convenient for the test of OBDII interface voltage waveform. Use the connector to convert the OBD1 interface into obd2 interface according to the diagnostic interface communication protocol. 1) Prepare battery A to supply power by connecting to No. 16 / 4 / 5 holes of Godiag GT100 & to the OBD2 diagnostic interface of the car. 2) Then replace the brand-new battery B with the used battery in the car, which will ensure that the car has fully power to prevent data loss and audio lo*ck-up or the malfunction due to lack of power to the E-C-U control module. - Green on pins 4/5 indicates ground - Red on pin 16 indicates power - Blue (flashing) is for communication lines Test leads and probes with 4mm banana plugs will connect directly into the 4mm safety sockets. The front panel has 3 switches, a master power switch for the box and two separate 12V ouputs for powering modules through the DB25 jumper cable. The GT100+ features a unique DB25 jumper cable which allows technicians to connect to and power up one or more modules when performing module diagnostics, progarmming or immobilzer work. Use the DB25 jumper cable to connect your scan tool’s OBD-II cable to any OBD-I or manufacturer-specific diagnostic port. Using the included AC adapter, the GODIAG can also be used as an auxiliary power supply and memory saver during battery service or replacement. Godiag GT100 Parameter Item Specification Diagnostic port OBDII Working voltage DC 9V-24V Work and power 0.5-0.6W Adapter power Input AC100v-240v, Output DC12V 1A Operating temperature range -20 to 70 °C ( -4 to 158 °F ) Storage temperature range -40 to 85 °C ( -40 to 185 °F ) Dimension L: 23cm, W:18cm, H:7cm 1pc x Host 1pc xOBD 2-in-1 extension cable 1pc xColored jumper cable 1pc xPower supply 12V 1pc xResistance 120 ohm 6pcs xBanana plug 24pcs xWire accessories, Dupont 2.54mm connector female pin
GODIAG GT100 Functions in Detail
Indicator Meaning:
2. SJE1850 wire
3. Manufacturer custom
4. Power grounding
5. Signal grounding
6. SAEJ2284《CAN》high
7. ISO9141-2&iso, DIS4230-4K wire
8. Manufacturer custom
10. SJE1850 wire《bus->
11. Manufacturer custom
12. Manufacturer custom
13. Manufacturer custom
14. SAEJ2284《CAN》low
15. ISO9141-2 & ISO/DIS 4230-4L wire
16. Car battery positive
2. E-C-U connection: single module connection
3. Banana plug extension connection:
4. Convert OBD1 diagnostic interface to the standard OBD2
5. Connect multiple E-C-U control modules at the same time, which is convenient for the professional engineers to detect and maintain.
6. Used as the extension cables: The space of the diagnostic interface location is too narrow to connect to the diagnostic tool, or the user find that the diagnostic cable is not long enough during maintenance. It can be extended by 1.2 meters.
7. Able to power the car when replacing the used battery.
[Notice 1. Turn on the power switch of Godiag GT100. 2. Don't turn on the ignition switch, don't start the car]
Godiag GT100 Hardware Connection Diagram:
Each OBD-II pin has a 4mm safety banana socket and a colored LED to indicate status display:
Package includes: