Holybro PM02 V3 PM02D PM03D Power Module 12S Power Distribution Board for APM Pix32 Pixhawk4 Flight Controller

Description:
This PM02 Power Module provides a simple way to supply regulated 5.2V to flight controller from the battery while providing current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable. It comes with pre-soldered wires, capacitor, and XT60 connector on both ends, along with shrink tubing on the PCBA for physical protection.

Specification:

  • Input Voltage: 2S-12S

  • PCB Cont. Current Rating: 60A

  • PCB Burst Current Rating: 100A (<60 Sec)

  • Max Current Sensing: 120A

  • Output: DC 5.2V & 3A Max

  • Voltage Divider: 18.182

  • Amperes per Volt: 36.364 

  • Weight: 20g

Please Note: 

- The XT60 Plug and 12AWG wire that are pre-soldered on the board is rating for 30A continuous current and 60A burst current (< 60 Seconds). If a higher current is being used, the plug type and wire size should be changed accordingly.
- This PM02 Power Module uses analog data output and is not compatible
to the Pixhawk 5X & 6X (Requires a digital PM like PM02D). 

Package Includes：

1x Power Module with XT60 Connectors Board (pre-soldered)
1x Electrolytic capacito: 220uF 63V (pre-soldered)
1x Molex 6 Position Connector 15 cm

1x JST GH 6 Position Connector 15 cm 

PM02D provides regulated power supply for your Pixhawk® 5X & 6X from the battery,as well as current consumption and battery voltage measurements, all through a 6pin cable. The on-board switching regulator outputs 5.2V and a maximum of 3A from LiPo batteries up to 6S. The Power Module comes completely assembled with XT60 connectors, wrapped in shrink tubing for physical damage protection.

It is not designed to power servos, please use your aircraft's ESC/BEC for that. The Molex 2.00mm pitch CLIK-Mate Wire-to-Board connector is rated for 3.0A current per contact.

Note:PM02D uses I2C digital signal data output and not compatible with Pixhawk 6C, Pixhawk4, Pixhawk4 Mini, pix32 v5, or Durandal flight controllers.

Spec：

Input voltage: 2S - 6S

PCB Cont. Current Rating: 60A

PCB Burst Current Rating: 100A (<60 Sec)

Max current sensing: 164A

Voltage and current monitor with I2C compatible interface 

Outputs 5.2V and 3A max 

Weight: 20g

Current Rating:

The PM02D comes with XT60 plugs with 14 AWG silicone wires rated for 30A continuous current and 60A burst current (<1 minute). If a higher current is needed, the plug type and wire size should be changed accordingly.


PIN MAP:

Package Includes：

1x  PM02D Power Module

1x  6pin 2.00mm pitch cable

Overview

This PM03D Power Module supplies clean 5.2V to flight controller from the battery and provides current consumption and battery voltage measurements via I2C digital signal through a 6 Pin 2mm Pitch CLIK-Mate cable, along with integrated esc power for up to 10 ESCs. Compatible to flight controller that uses I2C power monitor such as the Pixhawk 5X and 6X. 
It is design for multi-rotor like the X500 V2. It has both XT-30 & XT-60 connectors preinstalled for motor ESCs and Battery, as well as two 5V BEC and a selectable 8V/12V output different kinds of peripheral devices. 

Note:This PM is not compatible with flight controller that uses analog PM such as the Pixhawk6C, Pixhawk4, Pixhawk4 Mini, pix32 v5, or Durandal flight controllers.

Features

•    Plug & play, no additional setup required for QGroundcontrol & Mission Planner
•    XT-30 connectors and solder pads for easy motor ESC connection
•    Onboard voltage regulators: two 5.2V & one selectable 8V/12V
•    5V/A ports for powering companion computer or peripheral device
•    Selectable 8V or 12V triple row pin header for powering peripheral device

Technical Specification

  • Maximum input voltage: 6S battery

  • PCB Cont. Current Rating: 90A

  • PCB Burst Current Rating: 140A (<60 Sec)

  • Max current sensing: 164A

  • Connections

    • XT-60 for battery 

    • XT-30 for motor & peripheral device (battery voltage)

    • Solder pads in each corner (battery voltage)

    • CLIK-Mate 2.0mm for flight controller (5.2V/3A standalone BEC)

    • JST GH 4pin (5.2V/3A, BEC shared with 5.2V triple row pin header)

    • 2x Triple row pin header (5.2V/3A, BEC shared with JST GH 4pin)

    • 2x Triple row pin header (8V or 12V selectable by moving header jumper, 3A)

  • Dimension: 84*78*12mm (excluding wires)

  • Mounting: 45*45mm

  • Weight: 59g

    Please Note:
    The XT60 plug and 12AWG wire that PM03D comes with is rated for 30A continuous current and 60A instantaneous current (<1 minute). If a
    higher current is being used, the plug type and wire size should be changed accordingly.

Package Includes

  • 1x PM06 board

  • 1x 80mm XT60 connector wire (pre-soldered)

  • 1x Electrolytic capacitor: 220uF 63V (pre-soldered)

  • 1x 2.0mm pitch CLIK-Mate 6pin cable (To power flight controller)

  • 4pin JST GH to USB Type C

  • 4pin JST GH to barrel plug (2.1*5.5mm)

  • 4pin JST GH to barrel plug (2.5*5.5mm)

  • 4pin Pin Dupont Cable (2pc)

  • Nylon standoffs & nuts