Accuphase C-200 with power cord.
Tested and working.
» Confirmed unit powers on/off and LED light works.
» Confirmed power outlets on back are working.
» Confirmed audio input/output working.
» Confirmed audio volume, balance, etc are working.
Packaged and ready to ship.
21" x 19" x 8" @ 33 lb
----------------------- information below found at audio-database dot com -----------------------
This control amplifier was released as the first of the Accuphase series. The company name at that time was Kensonic.
The equalizer circuit is fully push-pull driven by direct
connection to all stages to improve the bare characteristics before NFB
(negative feedback) is applied, making it a high fidelity amplifier
circuit.
To handle input signals in a wide dynamic range, an A-class
drive pure complimentary service is used in the final stage of the
equalizer, and a dual plus / minus power supply system ensures a high
allowable input voltage.
In addition, a low-enhancement circuit is used to enhance the sense of volume when listening to music.
An attenuator that can be continuously adjusted by 10 dB is
provided to adjust the level of the DISC1 and DISC2 cartridges when you
want to lower the level of an extremely high-power cartridge to an
appropriate level, or when you want to listen to a comparison of two
cartridges using DISC1 and DISC2.
In addition, DISC1 is equipped with an input impedance
selector switch, which allows you to select between 47k Ω, 30k Ω and 20k
Ω.
A 25-Hz cutoff subsonic filter is also provided for disc playback.
Equipped with independent left and right tone control, the
turnover frequency can be switched between 200 hz, 400 hz, 2.5 khz and 5
khz for low and high tones respectively.
The change characteristic is ± 10 dB with a 11-contact rotary switch.
It is equipped with a low filter of 12dB/oct at 30 Hz or less to cut subsonic noise.
It is also equipped with a 5 khz, 12dB/oct high filter to cut hissing from tapes.
Tape I/O is installed in the Route 3 so that three tape recorders can be connected.
Two of them are capable of dubbing each other. The copy
switches are independent, so that it is possible to dub each other while
listening to the source.
A dedicated amplifier directly connected to pure complimentary
service is installed for the headphone to improve the sound quality of
the headphone.
All amplification stages are supplied from a power supply with a completely constant voltage to improve stability.
The speaker selector switch on the front panel allows you to
switch the speaker system using a special relay box (sold separately)
when the power amplifier is set out of reach.
Type | Accuphase stereo control amplifier | ||||||
Frequency Response | High level input : 20 Hz to 20000 Hz, + 0 -0.2 dB DISC and MIC input : 20 Hz to 20000 Hz, ± 0.2 dB |
||||||
Harmonic Distortion Factor | 0.05% or less (between 20 Hz to 20000 Hz at rated output) | ||||||
Input Sensitivity / Input Impedance | DISC1 : 2 ~ 6mV/20k Ω, 30k Ω, 47k Ω DISC2 : 2 ~ 6mV/47k Ω MIC : 2mV/47k Ω Tuner : 200mV/130k Ω AUX1, 2, Front : 200mV/130k Ω Tape Play1, 2, Front : 200mV/130k Ω |
||||||
Rated Output / Output Impedance | Main Output : 2.0V/200 Ω Headphones : 0.4V/0.3 Ω (maximum volume adjustment, at rated input) Tape Rec Output1, 2, Front : 200mV/200 Ω (at DISC input) Mono Output : 0.42V/38k Ω |
||||||
Maximum Power Level | 10 v or more (distortion factor 0.05%) | ||||||
Disk Max Input | 400 mv ~ 1.2 vrms (1 khz, distortion 0.05%) * 400 mv is the maximum DISC level control (equalizer gain 40 db) * 1.2 v is DISC level control minimum (equalizer gain 30 db) |
||||||
Gain | From the Tuner, AUX, and Tape Play inputs
|
||||||
S/N (Rated Output, Volume Adjustment Maximum) | Tuner, AUX, Tape Play : 90 dB or higher (nominal input) DISC, MIC : 74 dB or more (10 mV input) |
||||||
Volume Adjustment Interlock Error | within 1 dB | ||||||
Tone Controls |
|
||||||
DISC low enhancement (volume compensation circuit) | 0 dB, + 0.5 dB, + 1 dB (100 Hz) from the RIAA reference characteristic | ||||||
Compensator (volume control -30dB) | 50Hz:+10dB | ||||||
Filters | DISC subsonic filter : 25 Hz, 6dB/oct Low Filter : 30 Hz, 12 dB / High Filter : 5 kHz, 12dB/oct |
||||||
Semiconductors used | transistor : 80 Diode : 35 |
||||||
Power Supply | 100 V, 117 V, 220 V, 240 V, 50Hz/60Hz | ||||||
Power Consumption | 36W | ||||||
External Dimensions | 445 mm wide x 152 mm high x 355 mm deep | ||||||
Weight | 14kg |