If you have any questions about our keys.Please contact me first, I'd be happy to help you ,and I'll get back to you within 24 hours, except on weekends. Thank you🥂🥂🥂
Description of this item
Button: 2 Buttons
Frequency: 433 MHz
FCC ID: A269ZUA111
Blade: without
Battery,Circuit Board: with
Applications for:
2006-2007 Saab 9-3
2005-2006 Saab 9-2X
2002-2006 Subaru Baja
1999-2004 Subaru Forester
1999-2004 Subaru Impreza
1999-2004 Subaru Legacy
2000-2004 Subaru Outback
1996-2000 BMW Z3
Please Noted:
1- The product is a remote key ,with Internal parts (control board, chip , battery).
2- You need to program the key and cut the blade at a local automotive locksmith before using.
3-Please confirm your original key have the same appearance, FCCID with the product's.
Program:
Saab and BMW - Must be programmed by a professional automotive locksmith or dealership.
Programming for Subaru: 03-06 Baja, 01-04 Impreza, 01-04 Forester, 99-04 Legacy, 00-04 Outback
Obtain all remote transmitters for this vehicle.
1. Sit in the vehicle in the drivers seat with all doors, trunk, and rear gate closed.
2. Open and close the drivers door.
3. Put key into ignition switch. Cycle ignition switch from OFF to ON (ON is the position just before the engine cranks) ten times as quick as can be done ending up in the lock position. This must be done within 15 seconds. When done properly you will hear the horn sound. Now the vehicle is in programming mode.
4. Open and close the drivers door.
5. Press any button on the first remote. The horn will sound two times to indicate that remote was accepted.
6. Repeat steps 4 and 5 for each additional remote that you wish to program to vehicle.
7. Remove the key from the ignition switch. Horn will sound three times to indicate that vehicle is out of programming mode. Test all programmed remotes for proper function.
1. Sit in the vehicle in the drivers seat with all doors, trunk, and rear gate closed.
2. Open and close the drivers door.
3. Put key into ignition switch. Cycle ignition switch from OFF to ON (ON is the position just before the engine cranks) ten times as quick as can be done ending up in the lock position. This must be done within 15 seconds. When done properly you will hear the horn sound. Now the vehicle is in programming mode.
4. Open and close the drivers door.
5. Press any button on the first remote. The horn will sound two times to indicate that remote was accepted.
6. Repeat steps 4 and 5 for each additional remote that you wish to program to vehicle.
7. Remove the key from the ignition switch. Horn will sound three times to indicate that vehicle is out of programming mode. Test all programmed remotes for proper function.
Programming for Subaru: 2000 Impreza
Obtain all remote transmitters for this vehicle.
1. Open the driver's door.
2. Turn the ignition key ON (ON is the position just shy of cranking the engine).
3. Press and hold the programming/override button (located under or at the bottom of the driver's side dash). In approximately 20 seconds the system will start to cycle the door locks and the siren (if equipped) 3 times to indicate the system has entered the transmitter learn mode (DO NOT RELEASE THE PROGRAMMING/OVERRIDE BUTTON).
4. Press the #1 button (top left button) on the un-programmed transmitter. The system will respond by cycling the door locks and the siren (if equipped) one time to indicate the transmitter has been learned.
5. All other transmitters (up to four) also need to be programmed at this time.
6. Programming is now complete, let go of the programming/override button and turn ignition off to exit learn mode. Test all remotes for proper programming.
1. Open the driver's door.
2. Turn the ignition key ON (ON is the position just shy of cranking the engine).
3. Press and hold the programming/override button (located under or at the bottom of the driver's side dash). In approximately 20 seconds the system will start to cycle the door locks and the siren (if equipped) 3 times to indicate the system has entered the transmitter learn mode (DO NOT RELEASE THE PROGRAMMING/OVERRIDE BUTTON).
4. Press the #1 button (top left button) on the un-programmed transmitter. The system will respond by cycling the door locks and the siren (if equipped) one time to indicate the transmitter has been learned.
5. All other transmitters (up to four) also need to be programmed at this time.
6. Programming is now complete, let go of the programming/override button and turn ignition off to exit learn mode. Test all remotes for proper programming.
