Condition: BRAND NEW IN ORIGINAL PACKAGING

Warranty: 3 YEAR MANUFACTURER

• (1) JBL CSMA240 Commercial/Restaurant 2 x 40w Amplifier 4ohm/8ohm/70V/100V, 8 inputs
• (8) JBL CSS8004 4" Commercial 70V/100V 5w Ceiling Speakers 4 Restaurant/Bar/Cafe

Description of CSMA240:

Designed for commercial and industrial use, the CSMA 240 Commercial Series Mixer/Amplifier from JBL is a mixer/amplifier with eight mixer-channel inputs and two output channels. It's capable of reaching 40W of peak power with 5W per channel. The unit's front panel sports volume controls for each channel, as well as two master volume adjustment knobs, two sets of bass and treble controls, and a power switch. The volume controls are illuminated so they can be seen and operated in darkened environments.

The amplifier, capable of driving both eight and four Ohm loads, can be used with 70V and 100V distributed audio systems without the need for a separate transformer. On its back panel you'll find euroblock connections for mic/line inputs, as well as unbalanced RCA inputs, speaker connections, dip switches for input routing, and more. The unit is also equipped with two RJ45 connectors for use with JBL CSR-V in-wall volume controls (available separately).

This Commercial Series mixer/amplifier boasts such features as voice activating ducking (useful for paging over background music), priority muting for channels one and five, and a sleep mode which automatically powers down the unit when no audible signal has been received for longer than 30 minutes. Also, with two auxiliary outputs, you may connect to an additional amplifier, though the master volume and tone controls will have no bearing on the resulting signal.

Channel Modes

8 inputs with 2 outputs of 40W of power.

Controls

Independent Bass and Treble controls for each output channel.
Input level and output volume controls.

Hi-Z Switch
The Hi-Z switch will switch in the built-in output transformer allowing the unit to drive 70V or 100V speaker systems directly when connected to the appropriate output terminals.

Phantom Power
Phantom power (27 V) can be applied to all mic inputs by turning on Phantom Power within the dip switches.

VOX Function

Voice activated ducking is available on input channel 1 and channel 5. The audio input level required to activate ducking is set using the trim pot on the rear panel. Adjusting in the counter-clockwise direction will reduce that level, while the full clockwise setting will disable the VOX function.

Priority Muting

Channels one and five may be used as priority channels, muting all other channels when pins 4 and 5 are shorted using a switch closure. If the amplifier has entered sleep mode due to inactivity, invoking priority will also bring the unit out of sleep and ready for transmitting an announcement.

Remote Volume Control

Remote volume control can be implemented using a CSR-V controller connected via an Ethernet cable to the RJ45 connector on the back panel.

Sleep Mode

This unit is designed to go into sleep mode after approximately 30 minutes operating with no signal at any of the inputs. Return of signal (-40 dBu or 7.75mVRMS) to any input will wake the unit. Also, a switch closure across the priority input pins will return the unit to normal operating mode.

AUX output

An auxiliary output that you may connect to additional amplifiers is available. The audio signal is the mix of the input channels. Note that the master volume control and tone controls will have no effect on the aux output signal.

Manufacturing

Crown's DriveCore technology
HARMAN's GreenEdge environmental standards

Certifications and Approvals

Lead-free RoHS standards, utilizing recycled metals, and using an energy-saving powder coat process
Energy Star certified

Features:

• JBL CSMA240 Commercial/Restaurant 2 x 40w Amplifier 4ohm/8ohm/70V/100V, 8 inputs
• For Commercial and Industrial Use
• 40W into 8 or 4 Ohm Loads
• 5W Per Channel
• 8 Input Channels, 2 Output Channel
• Usable with 70 & 100V Systems
• Euroblock Mic/Line & RCA Inputs
• Hi-Z & 27V Phantom Power Switches
• Sleep Mode & 2 Auxiliary Outputs
• Voice Activated Ducking & Priority Mute

Specifications:

• Maximum Output Power: 40 W per channel into 4 Ohms or 8 Ohms, 1 kHz, = 0.5% THD
• Insertion Loss: 1 dB maximum for 70 and 100 V outputs
• Continuous Power: 5 W per channel
• Line Output Level: 5.0 V RMS into 10 kOhms
• Input Sensitivity: To obtain full rated power at 8 Ohms (or 5 VRMS to line output). Mic Input: 3 mV RMS. Line Input: 775 mV RMS. RCA Input: 300 mV RMS
• Number of Channels: Input: 8, Output: 2.
• Frequency Response: Measured at 2.83 V RMS into rated load impedance at any output. 4/8 Ohms Output: 20 Hz - 20 kHz, ±2 dB. 70 V/100 V Outputs: 80 Hz - 15 kHz ±2 dB. Line Out: 20 Hz - 20 kHz, ±1 dB
• Total Harmonic Distortion (THD): Measured at 2.83 V RMS into rated load impedance at any output. Power Amplifier Output: <0.5%, 20 Hz to 20 kHz. Line Output: 0.05% typical
• Signal to Noise Ratio: > 90 dB
• Nominal Input Impedance: Mic: 400 Ohms. Line: 20 kOhms (balanced). RCA: 50 kOhms.
• Minimum Load Impedance: Low Impedance Output: 4 Ohms. 70 V Output: 120 Ohms. 100 V Output: 240 Ohms.
• Crosstalk: -70 dB @ 1 kHz
• Controls:
• Front Panel:
• 8 x Input level rotary knobs
• 2 x Output volume-attenuating knobs
• 2 x Vox adjustment switches
• 1 x Power switch
• 2 x Bass potentiometers
• 2 x Treble potentiometers
• Rear Panel: 
•  2 x Input-routing dip switches (including phantom and Hi-Z switches) 
• Indicators:
• Front Panel:
• 8 x Mic/Line selector switch
• 8 x Input signal presence ring, gree
• 2 x Output volume ring, green
• 1 x Power switch ring, green/blue
• Connectors:
• Rear Panel:
• 1 x IEC power input
• 2 x Aux out connection points
• 6 x 3-pin euroblock connectors
• 2 x 5-pin euroblock connectors
• 6 x Dual RCA input connectors
• x RJ45, remote volume
• Operating Temperature / Humidity: 32 to 95°F / 0 to 35°C, 95% RH (non-condensing)
• Storage Temperature: -4 to 185°F / -20 to 85°
• Phantom Power: 27 VDC
• AC Input: 100-240 VAC, 50/60 Hz
• Dimensions (W x D x H): 17.2 x 11.9 x 1.7" / 436.9 x 302.3 x 43.2 mm
• Weight: Approximately 10.6 lb / 4.8 kg

Video of CSS8004 :

Description:

100 mm (4 in) Commercial Series Ceiling Speakers
JBL’s Commercial Series Ceiling Speakers provide excellent performance for paging and background music applications. High sensitivity across the product line provides maximum sound level, even at low tap settings.

Features:

• JBL CSS8004 4" Commercial 70V/100V 5 Watt Ceiling Speaker for Restaurant, Bar, Cafe
• Driver Size: 100mm Dual Cone
• Driver Sensitivity: 90 dB
• Frequency Range: 85 Hz - 18 kHz
• Coverage: 175°
• Driver Continuous Power Handling: 15 Watts
• 100V Taps: 5W, 2.5W, 1.3W
• 70V Taps: 5W, 2.5W, 1.3W, 0.7W
• 25V Taps: 5W, 2.5W, 1.3W, 0.7W
• Transformer Insertion Loss: 1.5 dB Maximum
• Transformer Connection: Bare Wire
• Motor Mass: 200 g (7 oz.)
• Matching CSS Backcan: CSS-BB4
• Bolt Mounting Circle to Backcan: 4 points on 6.5" diameter
• Cutout Diameter (Open-Back): 125mm (5.0")
• Cutout Diameter (In CSS-BB Backcan): 170mm (6.7")
• Depth (Behind Grille): 94mm (3.7")
• Grille Diameter: 198mm (7.8")
• Product Weight: 1.0 Lbs.

AudioSavings Return Policy:

At Audiosavings, we strongly believe in customer satisfaction and therefore offer free return shipping within 30 days of purchase on all items returned to us within the continental USA.

Prior to returning merchandise, contact us and we will give you a return authorization # and a return label.

You may return this item for a refund within 30 DAYS of purchase.

Warranty Repair/Exchange Period: 3 YEAR

If your item is defective or you want to return it for any reason within the first 30 days of when it was delivered to you; you have the following options:

• We will send you a pre-paid shipping label to replace the item for a brand new one.
• We will send you a pre-paid shipping label to exchange the item for another item of your choice. If the item you chose is more or less money we will work out the price difference with you.
• If you are returning a working item in used condition for a refund there will be a 20% used item fee deducted from your refund. All replacements and exchanges are free.

Replacement/Processing Time:

Your replacement or refund will process within 3-5 business days of when we receive the item.

Please note items with physical damage un-related to shipping are not covered under warranty. Registered software cannot be returned.

You MUST notify us within 48 hours if you receive an item that was damaged during shipping.

Process for returning items

Please email us with your eBay user ID, Item code / model #, Condition of the item, and the reason for your return. Please also indicate whether you would like a replacement, an exchange, or a refund. We will supply you with a reference number (RMA #) to put on the package which will ensure quick processing of your return. All returns require a RMA# to be returned back to our facility.