Sound Light Control Module Delay Adjustable 5 V 12 V 24 V
Product description
Our latest! Sound and light control / of voice module, all the the single sound sensitivity
/ sensitivity intensity / adjustable delay 1-60 S total of the whole, super stable!
Note: baby plate with and green, we do not the choice, random delivery.
The module uses:
The sound and the light intensity automatically detect when a sound exceeds the set limit,
the is energized and the for time delay period automatically, and then turn
Light control function can be activated also be closed. The control apparatus for a certain intensity of light or
intensity of light or less open.

Microphone for and welding by photosensitive resistor only for demonstration purposes, in order to avoid the
of the microphone sound, the effective delivery of products with an extension cable.
Module Features:
1. Voice / sound and light control Optional: You can only use the voice, sound and light control function can also be used at the same for time.
2. The two sound amplification, 100-5000 adjustable amplification, (corresponding to about 10 to 90 decibels of sound),
adjustable sound intensity threshold.
3. The intensity of light threshold 10-10000LX adjustable sensitivity (more or less equivalent to full black
for the half-day of brightness
4. Pull 1-60 S adjustable delay for time (for non-precision delay, capacitor loading and unloading delay for time,
with sound triggering a relationship).
5.Reverse polarity for protection, reverse of the power supply does not work, will not burn the module.
6. Wide input 5-30 V, ultra-wide scope.
Module parameters:
Supply (
of sound intensity: about 10-90 adjustable.
The light intensity threshold: approximately 10-10000Lx adjustable.
Delay time: 1-60 S adjustable (non-delay, capacitor loading and unloading delay for time, with the sound)
load current: 10A / 220V
Module size: 50mm * 33mm * 18mm (L * for * H), with a screw mounting holes positioned.
Special Note: Recently, buyers say the following questions 1: Instability Delay times, this module delay capacitive discharge delay, delay length fully triggered by the sound of capacitor loading and discharge decisions. looks great, delay the point president, the small point delay sound will be lower, the test is very simple blowing on, the delay is certainly much more than talk. 2: stop, the can perceive all sounds, the output, the will be the voice of the will module ,
Operation and wiring instructions (very important! for read carefully)
Module shipments have been detected before, but due to different specific areas, need to be adjusted for the track you want to use. Procedure is as follows:
The module using a multi-turn potentiometer, can be turned upwards about 30 weeks, please be patient adjustable swivel for head can hear a slight sound of this for time would not have rotated.
The basic is as follows: turn the light control function, delay for time to the minimum, adjust the sound intensity, and then adjust the delay, finally adjust the light intensity. Remember that the power of selecting the pin is not wrong!
1. Make sure that the photoresistor has been wrapped black tape type open type, turn the light control function before the commissioning the equivalent)
2. The power supply to the module: Confirm positive and negative (reverse will not burn, but does not work), if the supply 6V, be sure to turn the shorting Otherwise the module will burn
3. clockwise button to adjust the delay will be transferred to the lowest delay in order to facilitate adjustment of sound intensity.
4. in the relatively quiet environment, debugging, the intensity of the threshold adjustment button sound sensitivity increase clockwise anti-clockwise sensitivity. First clockwise adjustment, so that the is not closed (LED Then speak or clap, observe the LED is lit (due to being transferred shorter then immediately Gradually adjust the sensitivity until you need it.
5. After adjusting the appropriate acoustic intensity to gradually adjust the delay button to the left, shut down the talk module or clap your hands until the delay for time you need. Delay for up to one
6. If you want to use the light-control function (that is, only has been sticking), the photoresistor upper black ribbon ripped, button adjust the light intensity. Clockwise as the dim light (which is darker in order to pull) and the opposite direction of light becomes for To turn the light control function, use direct adhesive tape to cover the photoresistor.
Input and output wiring diagram
(此处放图1A30115-01)

Precautions!
1. Observe the safety devices to V!

Package includes:
1Pc*Sound Light Control Module Delay Adjustable 5 V 12 V 24 V