Features
Material:Aluminum
Motherboard:9th Ortur 32Bits
Laser Module:LU2-2/LF/SF/LU2-10A (Details are below↓↓）
Optical Power：10W/5.5W/1.6W
Electric Power：40W/20W/10W
Engraving Area：400*400mm
Engraving Speed：0-15000mm/min
Engraving materials:
Glass/Bamboo/Wood/Acrylic/Metal/Cloth/Leather/Stone/Plastic/Ceramic/Stainlessteel/Granite/Rubber/Mirror/Ceramics/Denim/Leaves/Paper/MDF, etc.
Cutting thickness:one-time cutting 20mm wood + 30mm acrylic
Cutting Material：Cardboard/MDF/Non-woven fabric/Leather/Plywood/Pine board/Acrylic/Some Plastic boards, etc.

Support mode：PWM

Firmware type：Support Ortur Laser 1.8 series firmware

Supported Operating Systems:

① LaserGRBL (freeware) supports Windows XP, 7, 8, 10

② LightBurn (paid software, lightburnsoftware.com) supports Windows, Mac OS, Linux

Installation time: 10-20 minutes

9th Ortur 32Bits Motherboard：

1. 32Bits MCU has the much higher frequency than 8 Bits MCU, arithmetic speed is faster, the operation is smoother, the           engraving & cutting precision is higher.

2. It could support any baud rate, save some delays due to command transmission, increase the engraving speed.

3. Support Ortur Laser 1.8 series firmware



5 Satety Protection：

1. Active Position Protection: When the machine is displaced or tilted, it would automatically stop the laser to prevent damage caused by the laser  shot out of the target.

2. Laser Beam Safety Guard: When the machine or computer from crashing during the engraving process, it would automatically stop the laser.

3. Exposure Duration Detection and Limitation: When the motors have no movement for a while, it would automatically stop the laser.

4. Flame detector + buzzer alarm: When the detector detect the flame, the buzzer alarm would sound and light alarm.

5. Emergency Stop Button: Any emergency, you could press the emergency stop button.



How to choose a laser module Tips

1. LU2-4-LF is good at engraving and better at cutting, and could support a higher speed. It has the air assist, but you need to buy a Air Compressor to support the air assist.

2. LU2-4-SF is good at cutting and better at engraving harder materials (such as stainless steel and other hard materials), and could support a higher speed.)

3. LU2-2 is good at engraving high-precision pattern, but speed couldn't be set too high.

4. It is not that the smaller the light spot, the better the effect. When engraving photos, you may need to increase the laser spot to get a better picture effect.

5. The competitors may falsely promote the power of similar laser modules as 40W or even 60W, please take care.





LU2-10A:More Powerful Engraving with True 10W Output Power LU2-10A is newly upgraded with a 10W laser module, which makes the cutting speed up to 15,000 mm/min. The compressed point is 0.05mm x 0.1mm.The optical power reaches to 10W. It can cut 30mm acrylic and 20mm wood. At the same time, the laser module of the engraving machine has a built-in air-assist interface, which is designed for cutting.

LU2-4-LF long focus laser module of the laser engraver has a real luminous power of 4,500-5,500mw and 0.17 x 0.25mm focal spot. With high power and a long depth of field, it is good for engraving and cutting.
Note: The module can work with an air compressor (not included in the package) for enhanced performance. recommends an air source with a flow of ＞40ml/min.
 
LU2-4-SF short focus laser module of the laser engraver has a real luminous power of 4,500-5,500mw and 0.12 x 0.15mm focal spot. With high power compressed spot, it is good at cutting and better at engraving hard materials.