|
Kingston HyperX Impact 8GB (2x8GB) Memory Kit
1600MHz DDR3L CL9 SODIMM Non-ECC Unbuffered 1.35V 204pins |
| |
![]() |
|
Condition : Brand New
Packaging : Retail |
brand new
RETAIL
Kingston HyperX Impact 8GB
(2x4GB) Memory Kit 1600MHz DDR3L CL9 SODIMM Non-ECC Unbuffered 1.35V 204pins...
Burst Length: 8
(Interleave without any limit, sequential with starting address '000' only), 4
with tCCD = 4 which does not allow seamless read or write [either on the fly
using A12 or MRS]... | |
![]() |
![]() |
Product Information: HyperX HX316LS9IBK2/8 is a kit of two 1G x 64-bit (8GB) DDR3L-1600 CL9 SDRAM
(Synchronous DRAM) 2Rx8, low voltage, memory modules, based on sixteen 512M x
8-bit DDR3 FBGA components per module.
Total kit capacity is 8GB.
Each module kit has been tested to run at DDR3L-1600 at a low latency timing of
9-9-9 at 1.35V or 1.5V.
HyperX Impact memory boasts the world’s fastest SO-DIMM frequency – 2666MHz – to
keep you ahead of the curve and level up your game.
It automatically recognises the platform it’s plugged into and auto overclocks
to the highest frequency published (up to 2400MHz) with no need to adjust system
BIOS settings.
So you get extreme performance that supports notebooks and other small form
factor systems using either AMD or the latest Intel CPU technologies with no
hassle at all – even if you’re a newbie.
Specification
General
Product Type: Memory Kit
Product Family: HyperX Impact
Memory
Memory Speed: 1600MHz
Pin Configuration: 204 pins
CAS Latency: CL9
Memory Type: DDR3L
Memory Size: 16384MB (2 module(s) x 8192MB)
Memory Package: SO-DIMM
Bus I/O Configuration: Unbuffered
Error Correction: Non ECC
Electrical
Voltage: 1.35V
Environmental
Operating Temperature: 0 to 85°C
Non Operating Temperature: -55 to +100°C
Physical
Case Colour: Black
Features
JEDEC standard 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V) Power Supply
VDDQ = 1.35V (1.28V ~ 1.45V) and 1.5V (1.425V ~ 1.575V)
800MHz fCK for 1600Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 11, 10, 9, 8, 7, 6
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with starting address
'000' only), 4 with tCCD = 4 which does not allow seamless read or write [either
on the fly using A12 or MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240
ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower than TCASE 85°C, 3.9us at 85°C < TCASE <
95°C
Asynchronous Reset
PCB : Height 1.180 inch (30.00mm), double sided component
| |
![]() |
![]() |
|
|
![]() | |
![]() |
![]() |
uksoftwaretech. All rights reserved and all third party trade marks acknowledged. E&OE. |
![]() ![We proudly accept all major credit and debit cards]()
| | |