Complete set 1x100Watt 12Volt 1000mm voltage converter 600W 10A charge controller yellow island system

Scope of delivery:

1 piece solar module 100 watt monocrystalline, 1000mmx675mmx30mm, 5 busbars

1 piece 10A LCD solar charge controller

1 pair of 2m 4mm² connection cable charge controller > battery with battery terminals

1 pair of 5m 4mm² connection cables module > charge controller with pressed-on solar plugs

(Tested solar cables made in Germany are used)

Solar module properties

robust aluminum frame
Weatherproof front glass hardened for protection against hail, snow, ice etc.
Junction box on the back, weatherproof

Technical data module:
Weight: 9.4kg
Dimensions: 1000mm x 675mm x 30mm
Rated power Pmax: 100 W +3%
Nominal voltage Vmp: 18.4 V
Permissible system voltage: 1000 V
Front: made of special glass
Rated current Imp: 5.44 A
Open circuit voltage Voc: 23.21 V
Short circuit current Isc: 5.83 A

Voltage converter 600 Watt NM Series

With this device you can generate 230 V alternating voltage from 12 V direct voltage (e.g. from car batteries, truck batteries or batteries from solar island systems) and thus operate many household appliances with a nominal voltage of 230 V.

Scope of delivery: converter, DC connection cable with alligator clips approx. 60cm, DC connection cable for cigarette lighter, operating instructions incl. Wiring diagram

Advantages:

modified sine voltage
Soft start function
1x protective contact socket
Average self-consumption without load when switched off 0 watts
Reverse polarity protection for battery (fuse blows)
Automatic shutdown in case of overload or short circuit
Approved for use in vehicles
Sturdy housing made of aluminum and molded sheet metal
Certificates: Transducer, CE, RoHS; E8 Manufacturing according to din ISO 9001:2000

Details:

Weight: 1.1kg
Dimensions: 226 x 108 x 62 mm
Output voltage: 230 V (50Hz)
Continuous power: 600 W
Peak power: 1200 W at least 20 ms for start-up or Cold currents
Input voltage operating range: 12 V
Undervoltage shutdown: < 10.4V
Overvoltage shutdown: > 15.0 V
relative humidity: < 60%
Efficiency: > 85%
Socket: 1 Schuko socket
USB device power supply: 1x 5V 2.1A
Overtemperature protection shutdown: > 60°
Low voltage alarm: < 10.6V
Installation of cable remote control: no installation possible

Charge controller 10A yellow

The charge controller 060010G is connected between the solar modules and the battery and is therefore responsible for controlling the charging process, so the battery can always be charged to its maximum. A built-in microprocessor charges the battery gently, guaranteeing your battery a long service life.

All voltages, charging processes and parameters can be shown on the display. You can set the final charging voltage using the control panel, so the solar charge controller can be used on any battery. You can set the voltage from which the undervoltage protection should be activated and from which operating voltage the undervoltage protection should reset again.

Overcharging the battery can be prevented because the charge controller stops the charging process when the set end-of-charge voltage is reached and switches to trickle charging.

Advantages:

Over- and deep-discharge protection for the battery prevents feed back to the solar panel
Automatic shutdown should the charging current exceed the capacity of the controller
Automatic shutdown in the event of a short circuit
Prevents feedback to the panel
Automatic shutdown in the event of overload and short circuit
Consumers are switched off when the accumulators are undervolted
Overload and short-circuit protection, consumer shutdown in the event of accumulator undervoltage
Automatic temperature compensation
Automatic voltage level identification system
Intelligent PWM charging mode
Adjustable final charging voltage
Night and time control
Display of charging and discharging power in Ah
Protection against battery discharge via solar connection
Undervoltage shutdown of the small consumer output
Protection in the event of battery polarity reversal
Protection against overload and short circuits
for lead acid, gel and AGM batteries (batteries)
Representation with LCD graphic display
Display of the battery charge status is displayed

Details:

Weight: 0.3kg
Battery voltage: 12V or 24V automatic detection
Charging current: 10 A
Own consumption: < 0.015A
Dimensions: 160mm x 88.2mm x 42.4mm
Color: gray/black

The cable sets supplied are configured and checked by our employees. They contain the necessary connections (solar plugs, battery terminals or wire end sleeves). Tested solar cables made in Germany are used.

To store the electricity generated, you need a 12V battery storage (rechargeable battery). This set is suitable for charging lead acid, gel and AGM batteries (batteries).

Product description

This is a 1x100W complete set with monocrystalline solar module from solartronics with an output of max. 100 watts. The surface is made of tempered glass, well protected from Allen weather conditions. The frame is made of aluminum, the junction box on the back is weatherproof.

Our solar modules are tested and have the appropriate certificate.

Solar modules with monocrystalline solar cells

Monocrystalline solar cells are manufactured from the semiconductor material silicon in a complex process. Compared to polycrystalline solar cells, they have a very high silicon content, are highly efficient and are the most effective solar modules in direct sunlight.

Monocrystalline solar cells are therefore very suitable if there is only a small area available for a photovoltaic system, if a very high output is to be achieved in direct sunlight or if the area is oriented directly to the south.

Areas of application of monocrystalline solar cells

Solar power can be used in a variety of ways. Whether as a large system for economical grid feeding in single or multi-family homes or self-sufficient island systems without a grid connection. On mobile homes, boats, allotments or small houses of all kinds. However, a battery is required for this.

Monocrystalline solar cells from solartronics are ideal for all of these areas of application.

Purchase process

After the auction, you will automatically receive an email to your email address stored on eBay to initiate the purchase process. During the checkout process, you can combine several of our auctions and save shipping costs, adjust your billing and delivery address and choose the payment and shipping method. You will also find all information about payment processing there, such as our account details and intended use in the case of advance payment / bank transfer. If you do not receive this email within 2 hours, please contact us.