MUCAR VO6 as the 2024 Highest-level FULL OBD II Diagnostic Device For DIY users supported include Code Reading/Clearing data stream,Actuation Test ,Special Functions etc
1.Free system-wide code reading, code clearing, data streaming and upgrades for all models.

2.The 28 reset function are free to use .

3.5.99-inch display is convenient for you to diagnose the car in real time

4.Android system can be upgraded online.

5.The whole system diagnoses more than 93 automobile brands.

6.Diagnosis covers all models that support OBD protocol after 1996.

7.Equipped with VIN code intelligent identification models.

8.MUCAR series design, dustproof, shockproof, easy to store

9.2G RAM/ 16G ROM,Support Bluetooth and WiFi connection

Product Homepage Function

1. Intellignt diagnosis, automatic identification of vin, enter the diagnosis system 2. Maintenance service, maintenance service download, enter the system 3. MUCAR mall, subscription software, software upgrade, realize full-function diagnosis 4. Online upgrade , The software version can be updated 5. Vehicle files, save the data records of the detected vehicles, such as: report 6. Settings

Lifetime Free All Cars Full System Diagnostic:

Lifetime Free All Cars 28 Reset Services

1. Oil Reset
The lightening of the car maintenance light indicates that the vehicle needs maintenance.Reset the mileage or driving time to zero after the maintenance, so the maintenance light will go out and the system will start a new maintenance cycle.

2. Elec.Throttle Adaption

Elec. Throttle Adaption is to utilize the car decoder to initialize the throttle actuator so that the learning value of the ECU returns to the initial state.

3.Steering Angle Reset

To reset the steering angle, first find the relative zero point position for the car to drive in straight line.Taking this position as reference,the ECU can calculate the accurate angle for left and right steering.

4. Battery Matching

This function enables you to perform a resetting operation on the monitoring unit of vehicle battery, in which the original low battery fault information will be cleared and battery matching will be done.

5. ABS Bleeding

When the ABS contains air, the ABS bleeding function must be performed to bleed the brake system to restore ABS brake sensitivity.

6.Break-pad Reset

lf the brake pad wears the brake pad sense line, the brake pad sense line sends a signal sense line to the on-board computer to replace the brake pad.After replacing the brake pad, you must reset the brake pad.Otherwise, the car alarms.

7.DPF Regeneration
DPF regeneration is used to clear PM(Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance.

8.Gear Learning

After the engine ECu, crankshaft position sensor,or crankshaft flywheel is replaced, or the DTC 'gear not learned' is present, gear learning must be performed.

9. IMMO Service To prevent the car being used by unauthorized keys, the anti-theft key matching function must be performed so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car.

10. Injector Coding

Write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder so as to more accurately control or correct cylinder injection quantity.

11.TPMS Reset

Note:Cooperate with wireless tire pressure diagnosis tool to realize TPMS activation, programming and learning functions

12. Suspension Matching

This function can adjust the height of the body. When replacing the body height sensor in the air sus pension system, or control module or when the vehicle level is incorrect, you

need to perform thisfunction to adjust the body height sensor for level calibration.

13. AFS Reset

This feature is used to initialize the adaptive headlamp system.

14.A/T Learning

This function can complete the gearbox self-learning to improve gear shifting quality.

15.Sunroof Initialization

This function can set the sunroof lock off, closed when it rains,sliding /tilting sunroof memory function,temperature threshold outside the car etc.

16. EGR Adaption

This function is used to learn the EGR valve after it is cleaned or replaced.

17. ODO Reset

ODO reset is to copy, write, or rewrite the value of kilometers in the chip of odometer by using a car diagnostic computer and data cable, so that the odometer shows the actual

18. Airbag Reset

This function resets the airbag data to clear the airbag collision fault indicator.

19. Transport Mode

ln order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote

control key, etc.At this time, the transport mode needs to be deactivated to restore the vehicle to normal.

20. A/F Reset

This function is applied to set or learn Air/Fuel ratio parameters.

21. Stop/Start Reset

This function is used to open or close the automatic start-stop function via setting the hidden function in ECU(provided that the vehicle has a hidden function and supported by hardware).

22. NOx Sensor Reset

NOx sensor is a sensor used to detect the content of nitrogen oxides (NOx) in engine exhaust. lf theNOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned value stored in the engine Ecu.

23. AdBlue Reset

(Diesel Engine Exhaust Gas Filter) After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required.
24.Seat Calibration
This function is applied to match the seats with memory function that are replaced and repaired.

25.Coolant Bleeding

Use this function to activate the electronic water pump before venting the cooling system.

26.Tyre Reset

This function is used to set the size parameters of the modified or replaced tire.

27.Windows Calibration

This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window.
28. Language Change

This function is used to change the system language of the vehicle central control panel.

Free Full OBDII Functions:

*-Read extensive current, pending and permanent codes in OBD system quickly 
*-Clear detected fault codes and turn off the Check Engine Light efficiently 
*-View graphical live data of vehicle's computer module(s) for easy analyses 
*-View the vehicle's operating parameters at the moment a DTC is detected 
*-Read I/M readiness status to have a vehicle inspected for state emissions compliance 
*-Perform O2 sensor test to check fuel efficiency and vehicle emissions 
*-Read the results of on-board diagnostic monitoring tests for specific components/systems 
*-Retrieve the vehicle information of VIN, CINs, and CVNs completely 
*-Perform the component Test by allowing initiating a leak test for the vehicle's EVAP system

4 IN 1 Scientific Data Management: Live Data Stream Graph & Record Data & Diagnosis Record Playback & Print Report

The professional vehicle scanner tool can scientific graph data, record data, play back data, freeze frame,and print reports.
In the real-time diagnosis process, important diagnosis information can be instantly stored in the memory, including reading of fault codes and frozen frames and real-time data streams.
After real-time diagnosis is completed, Diagnosis function record playback, the diagnosis information and process previously saved in the memory can be replayed to facilitate the analysis of various data information.
One-click generation of a diagnosis report after diagnosis will help users quickly solve problems, avoid blind maintenance, and save money/time.

Support 13 Multi-Langauge

Do you want to use your native language for diagnosis? Don’t worry, MUCAR VO6 provides multiple languages for you to switch ，English , French , Spanish , German , Russian , Italian , Portuguese , Japanese ,Polish

Support 128+ Worldwide Vehicle Coverage

Support 126+ Car Brands and 1000+ Vehicles

USA：

For BXGM,For CHRYSLER, For AUSTFORD, For GM,USAFORD

EUROPE:

For ASTONMARTIN,For AUDI,For BENZ,For BMW,For BXFIAT,For CITROEN,For FERRARI,For FIAT,For GAZ,For LANDROVER,For MASE,RATI,For OPEL,For PAZ,For PEUGEOT,For PORSCHE...

Austrillia:

For AUSTFORD,For AUSTHOLDEN

Asia:

For BAIC,For CHANGAN,For CHANGCHENG,For CHANGHE,For DAEWOO,For DAIHATSU,For DFXK,For FLYER,For FUTIAN,For HAFEL For HMAZDA,For HONDA,For HUACHEN,For HYUNDAI,For IKCO,For INDIANMARUTI,For INDIANTATA,For ISUZU,For IVECO.IZH,For JACTY JIAO,For JINLONG,For JOYLONG,For JPISUZU,KIA,For LIFAN, For LIUWEITY ,For LUXGEN,For MAHINDRA,For MALAYSIA PERODUA,For MALAYSIA PROTON,For MARUT,For MAXUS,For MAZDA,For MITSUBISHI...

How to Register/Update MUCAR VO6

1.Initial Use

2.Turn on the Machine

3.Language Setting

4.Connect WIFI

5.Choose Time Zone

6.User Agreement

7.Create an Account

8.Typing in Business Information

Product Parameters:

Display Screen ：5.99-Inch/TFT(IPS)

Connection :Wi-Fi/Bluetooth

RAM:2G ROM:16G

Working Temperature : 32℉~122℉

Storage Temperature: -4℉~144℉

Packing List:

1*MUCAR VO6 Host

1*Diagnostic dongle

1*Charging cable

1*Multi-Language Manual