① Probe Tip: Contacts the circuit or component to be tested.
② Head Lights: lluminates dark work areas or work areas at night.
③ LCD Display: Indicates test results.
④ Red/Green Polarity Indicator: Identifies positive, negative or open circuits.
The RED indicator lights up when the Probe Tip is contacting a positive circuit.
The GREEN indicator lights up when the Probe Tip is contacting a negative circuit.
⑤ Adaptor: Connects to the battery.
⑥ Power Switch: Allows you to conduct a positive or negative battery current to the tip for activating and testing the function of electrical components.
⑦ Auxiliary: Ground Lead - Assists test as a ground lead.
⑧ Mode Button: Selects the work mode: AC Voltage, DC Voltage, Resistance, Diode..

Feature

1.[AC & DC Voltage Detection Mode]:

AC detects the maximum and minimum voltage, supply frequency and duty cycle of the circuit under test. While DC volt. detection detects the voltage value of the circuit under test.

2.[Resistance Test & Diode Test Mode]:

It detects the resistance between the circuit probe under test and the auxiliary ground; While Diode Test can quickly test the operation of the diode assembly and determines if it is conducting.

3.[Ultra Extension Inspection Cable 6m]:

Covering from the front to the rear of the vehicle, you can easily inspect the entire electrical circuit system.

4.[Current Overload Protection]:

When the current overload, VDIAGTOOL V200 Automotive Circuit Tester will automatically disconnect the protection circuit to reduce unnecessary losses.

5.[Multi-language options]:

Choose from 7 languages: English, German, Spanish, French, Italian, Russian, Portuguese

V200 Electrical System Circuit Tester Functions:

1. Power injection, measuring, ground testing, polarity checking, continuity testing and component activation.
2. Read the AVO meter, voltage, current, and resistance.
3. Energize the electrical components, such as the cooling fan, relay etc.
4. Activate the components
5. Determine the positive, negative and open circuit.
6. Test the bad ground contacts, follow and locate short circuits without wasting the fuse.
7. Test the continuity of the power switch, relay and diode.
8. Protect the tool from overload.
9. Allow you to work in the dark area by using the built-in head light.
10. Test along the vehicle by the long cable.

Important Note

To prevent personal injury or damage to vehicles or the test Tool, read this instruction manual first and observe the following safety precautions whenever working on a vehicle:
1. Always perform automotive testing in a safe environment.
2. Wear eye protection that meets ANSI standards.
3. Keep clothing, hair, hands, tools, test equipment, etc away from all moving or hot enging parts.
4. Operate the vehicle in a well ventilated work Area: Exhaust gas are poisonous.
5. Put blocks in front of the drive wheels and never leave the vehicle unattended while running tests.
Use ectreme caution when working around the ignition coil, distributor cap, ignition wires and spark plugs. These component create Hazardous voltage when engine is running.
6. Put the transmission in PARK (for automatic transmission) or NEUTRAL (for manual transmission) and make sure the parking brake is engaged.
7. Keep a fire extinguisher suitable for gasoling/ chemical/ electrical fires nearby.
8. Don't connect or disconnect any test equipment while the ignition is on or the enging is running.
9. Keep the tool dry, clean, free from oil/water or grease. Use a mild detergent on a clean cloth to clean the outside of the test tool, when necessary.
10. When the power switch in the tool is depressed, battery current/voltage is conducted directly to the tip which may cause sparks when contactiong ground or certain circuits.
Therefore the tool should NOT be used around flammables such as gasoline or its vapors. The spark of an energized tool could ignite these vapors. Use the same caution as you would when using an arc welder.

Specifications:

Display: TFT color display (168x 128 dpi)
Operating Temperature: 0 to 60°C (32 to 140°F)
Storage Temperature: -40 to 70°C (-40 to 185°F)
External Power: 12.0 or 24.0 V power provided via vehicle battery
Dimensions (L x Wx H): 178x 47 x 28mm (7 x 1.85 x0.09 in)
Weight: 1.2Kg (0.22LB)

Package Included:

1×VDIAGTOOL V200 Electric Circuit Tester
1×Probe Tip
1×20ft Extension Cable
1×Battery Hookup Clips
1×Cigarette Lighter Adapter
1×User's Manual
1×Rugged Blow Molded Case