HC-06 4PIN
Specification:
Note:It's HC-06 Bluetooth module
Allows your device to both send or receive the TTL data via Bluetooth technology without connecting a serial cable to your computer.
Works with any USB Bluetooth adapters.
Default Baud Rate: 9600,8,1,n.
Built in antenna.
Coverage up to 30ft.
Bluetooth version: V2.0+EDR
Operating voltage: 3.3V
Default Baud Rate: 9600,8,1,n.
Signal coverage: 30ft
Cable length: 21.5cm
Item size: 4.3 * 1.6 * 0.7cm
Item weight: 3g
Package size: 9 * 3 * 1cm
Package weight: 8g
Commercial Series: Bluetooth module board Series
With LED indicator light, use 150mA and 3.3V regulation chip.
With VCC、GND、TXD、RXD foot for the Bluetooth
With "Re-seach" button(ON/OFF/WAKE foot for it , external MCU outinput "High level" can control module to re-seach)
Compatible with bluetooth master module"、slave module"or master-slave(whole) module.
Input voltage: 3.3~6V
Size: 1.55cm*3.98cm
Note:
input power supply 3.3~6V, Prohibit more than 7V
No "Automatically prevent power supply peversing func", so please correctly connect power supply
We advise to install "Bluetooth master module"
The "State" is output foot for LED status, when bluetooth "Unconnected", output "Pulse" ; when bluetooth "connected", output "High level", we can determine the states from "MCU"
If only the board , No any "Bluetooth Function "
Note:It's HC-06 Bluetooth module
Allows your device to both send or receive the TTL data via Bluetooth technology without connecting a serial cable to your computer.
Works with any USB Bluetooth adapters.
Default Baud Rate: 9600,8,1,n.
Built in antenna.
Coverage up to 30ft.
Bluetooth version: V2.0+EDR
Operating voltage: 3.3V
Default Baud Rate: 9600,8,1,n.
Signal coverage: 30ft
Cable length: 21.5cm
Item size: 4.3 * 1.6 * 0.7cm
Item weight: 3g
Package size: 9 * 3 * 1cm
Package weight: 8g
Commercial Series: Bluetooth module board Series
With LED indicator light, use 150mA and 3.3V regulation chip.
With VCC、GND、TXD、RXD foot for the Bluetooth
With "Re-seach" button(ON/OFF/WAKE foot for it , external MCU outinput "High level" can control module to re-seach)
Compatible with bluetooth master module"、slave module"or master-slave(whole) module.
Input voltage: 3.3~6V
Size: 1.55cm*3.98cm
Note:
input power supply 3.3~6V, Prohibit more than 7V
No "Automatically prevent power supply peversing func", so please correctly connect power supply
We advise to install "Bluetooth master module"
The "State" is output foot for LED status, when bluetooth "Unconnected", output "Pulse" ; when bluetooth "connected", output "High level", we can determine the states from "MCU"
If only the board , No any "Bluetooth Function "
Package Included:
1*Bluetooth module with backboard
HC-05 6PIN
Specification:
Note:It's HC-05 Bluetooth module Slave and master two in one module
this module can be set to a transmitter or receiver, transmitter could pairing with receiver , receiver and receiver or transmitter and transmitter can't communication between, receiver could pairing with computers and cell phone bluetooth , when buying, the default for receiver.
1. It is HC-05.
2. Use the CSR mainstream bluetooth chip, bluetooth V2.0 protocol standards.3. Module working voltage 3.3 V.
4. Potter default rate of 9600, the user can be set up.
5. The core module size : 28 mm x 15 mm x 2.35 mm.
6. Working current: matching for 30 MA, matching the communication for 8 MA.
7. Dormancy current: no dormancy.
8. Used for GPS navigation system, water and electricity gas meter reading system.
9. With computer and bluetooth bluetooth adapter, PDA, seamless connection equipment
- Commercial Series: Bluetooth module board Series
- With LED indicator light, use 150mA and 3.3V regulation chip.
- With VCC、GND、TXD、RXD foot for the Bluetooth
- With "Re-seach" button(ON/OFF/WAKE foot for it , external MCU outinput "High level" can control module to re-seach)
- Compatible with bluetooth master module"、slave module"or master-slave(whole) module.
- Input voltage: 3.3~6V
- Size: 1.55cm*3.98cm
Note:
input power supply 3.3~6V, Prohibit more than 7V
No "Automatically prevent power supply peversing func", so please correctly connect power supply
We advise to install "Bluetooth master module"
The "State" is output foot for LED status, when bluetooth "Unconnected", output "Pulse" ; when bluetooth "connected", output "High level", we can determine the states from "MCU"
If only the board , No any "Bluetooth Function .
We advise to install "Bluetooth master module"
The "State" is output foot for LED status, when bluetooth "Unconnected", output "Pulse" ; when bluetooth "connected", output "High level", we can determine the states from "MCU"
If only the board , No any "Bluetooth Function .
Package Included:
1x HC-05 bluetooth module with backboard
HC-06 4Pin Affordable Edition
Product feature:
1. Using high-quality materials, the quality is guaranteed
2. The appearance of the product is exquisite and small
3. Multiple specifications optional
4. The product is covered with a transparent heat-shrinkable tube, which is dust-proof
5. With anti-static ability
1. Using high-quality materials, the quality is guaranteed
2. The appearance of the product is exquisite and small
3. Multiple specifications optional
4. The product is covered with a transparent heat-shrinkable tube, which is dust-proof
5. With anti-static ability
Product parameters:
1. The core module uses the HC-06 slave module, the outgoing interface includes VCC, GND, TXD, RXD, and the LED status output pin is reserved. The microcontroller can judge whether the Bluetooth has been connected through the status of this pin, and the KEY pin is invalid for the slave machine.
2.led indicates the bluetooth connection status, flashing means no bluetooth connection, steady light means bluetooth is connected and the port is open
3. The bottom plate is 3.3V LDO, the input voltage is 3.6~6V, the current is about 30mA when not paired, and about 10mA after pairing, and the input voltage is prohibited to exceed 7V
4. The interface level is 3.3V, which can be directly connected to various microcontrollers (51, AVR, PIC, ARM, MSP430, etc.), 5V microcontrollers can also be directly connected, without MAX232 or through MAX232
5. The effective distance in the open space is 10 meters, and it is possible to exceed 10 meters, but the connection quality of this distance is not guaranteed
6. After pairing, when it is used as a full-duplex serial port, it does not need to understand any Bluetooth protocol, but it only supports the communication format of 8 data bits, 1 stop bit, and no parity check, which is also the most commonly used communication format and does not support other formats.
7. When the bluetooth connection is not established, the baud rate, name, and pairing password can be set through AT commands. The set parameters are saved after power off, and the bluetooth connection will automatically switch to the transparent transmission mode.
8. This link is a slave, and the slave can be paired with various computers with Bluetooth function, Bluetooth hosts, most mobile phones with Bluetooth, PDA, PSP and other intelligent terminals, and cannot be paired between slaves.
1. The core module uses the HC-06 slave module, the outgoing interface includes VCC, GND, TXD, RXD, and the LED status output pin is reserved. The microcontroller can judge whether the Bluetooth has been connected through the status of this pin, and the KEY pin is invalid for the slave machine.
2.led indicates the bluetooth connection status, flashing means no bluetooth connection, steady light means bluetooth is connected and the port is open
3. The bottom plate is 3.3V LDO, the input voltage is 3.6~6V, the current is about 30mA when not paired, and about 10mA after pairing, and the input voltage is prohibited to exceed 7V
4. The interface level is 3.3V, which can be directly connected to various microcontrollers (51, AVR, PIC, ARM, MSP430, etc.), 5V microcontrollers can also be directly connected, without MAX232 or through MAX232
5. The effective distance in the open space is 10 meters, and it is possible to exceed 10 meters, but the connection quality of this distance is not guaranteed
6. After pairing, when it is used as a full-duplex serial port, it does not need to understand any Bluetooth protocol, but it only supports the communication format of 8 data bits, 1 stop bit, and no parity check, which is also the most commonly used communication format and does not support other formats.
7. When the bluetooth connection is not established, the baud rate, name, and pairing password can be set through AT commands. The set parameters are saved after power off, and the bluetooth connection will automatically switch to the transparent transmission mode.
8. This link is a slave, and the slave can be paired with various computers with Bluetooth function, Bluetooth hosts, most mobile phones with Bluetooth, PDA, PSP and other intelligent terminals, and cannot be paired between slaves.
Product tips:
TXD: sender, generally expressed as its own sender, normal communication must be connected to the RXD of another device
RXD: Receiver, generally expressed as its own receiver, normal communication must be connected to the TXD of another device
During normal communication, the TXD of its own is always connected to the RXD of the device!
Self-receiving and self-transmitting: During normal communication, the RXD is connected to the TXD of other devices, so if you want to receive the data sent by yourself, as the name implies, that is, you will receive the data sent by yourself, that is, your own TXD is directly connected to the RXD to test its own transmission and reception. Whether it is normal or not is the fastest and simplest test method. When there is a problem, first do this test to determine whether the product is faulty, also known as loopback test.
TXD: sender, generally expressed as its own sender, normal communication must be connected to the RXD of another device
RXD: Receiver, generally expressed as its own receiver, normal communication must be connected to the TXD of another device
During normal communication, the TXD of its own is always connected to the RXD of the device!
Self-receiving and self-transmitting: During normal communication, the RXD is connected to the TXD of other devices, so if you want to receive the data sent by yourself, as the name implies, that is, you will receive the data sent by yourself, that is, your own TXD is directly connected to the RXD to test its own transmission and reception. Whether it is normal or not is the fastest and simplest test method. When there is a problem, first do this test to determine whether the product is faulty, also known as loopback test.
Package list:
Module X1
Module X1