XH-W3001
Features:
automatic mode
Wide temperature control range
High temperature control accuracy
reverse connection protection
easy installation
automatic mode
Wide temperature control range
High temperature control accuracy
reverse connection protection
easy installation
Product parameters:
Product name: Microcomputer temperature controller
Product Model: XH-W3001
Supply voltage: 12/24/220V
Temperature measurement range: -50℃~110℃
Temperature control range: -50℃~110℃
Temperature control accuracy: 0.1℃
Load power: 120/240/1500W
Measurement input: NTC10K waterproof probe L=1 meter
output type: direct output
Output capacity: max 10A
Installation hole distance: 73mm (diameter 4mm)
Appearance size: 60*45*31mm
Product name: Microcomputer temperature controller
Product Model: XH-W3001
Supply voltage: 12/24/220V
Temperature measurement range: -50℃~110℃
Temperature control range: -50℃~110℃
Temperature control accuracy: 0.1℃
Load power: 120/240/1500W
Measurement input: NTC10K waterproof probe L=1 meter
output type: direct output
Output capacity: max 10A
Installation hole distance: 73mm (diameter 4mm)
Appearance size: 60*45*31mm
Instructions
To set the startup temperature:
Press the up button once, the startup temperature will be displayed, long press the up button for about 3 seconds, the startup temperature number will flash, and the desired temperature value can be set by the up and down buttons
Set stop temperature:
Press the down button once to display the stop temperature, long press the button for about 3 seconds, the stop temperature number will flash, and the desired temperature value can be set by the up and down buttons
reset:
When the power is on, press and hold the up and down keys at the same time, the digital tube displays 888 and then automatically jumps to the detection temperature, that is, restores the factory settings
To set the startup temperature:
Press the up button once, the startup temperature will be displayed, long press the up button for about 3 seconds, the startup temperature number will flash, and the desired temperature value can be set by the up and down buttons
Set stop temperature:
Press the down button once to display the stop temperature, long press the button for about 3 seconds, the stop temperature number will flash, and the desired temperature value can be set by the up and down buttons
reset:
When the power is on, press and hold the up and down keys at the same time, the digital tube displays 888 and then automatically jumps to the detection temperature, that is, restores the factory settings
XH-W3002
Feature:
The high-brightness digital tube clearly displays, whether it is used during the day or at night, it can be read clearly
The sensor can be replaced at will by using the 2P terminal. When you need to use other probes, you can replace it at will
ABS material shell, exquisite and beautiful, high mechanical strength, good electrical performance, anti-aging
-50~110℃ ultra-wide temperature control range, can be used in various temperature control fields, 0.1℃ temperature control accuracy, to meet your control needs
Wiring input and output design, more convenient to use in various industrial control equipment, multi-strand wire 300V/20A excess configuration, safe and reliable
The sensor can be replaced at will by using the 2P terminal. When you need to use other probes, you can replace it at will
ABS material shell, exquisite and beautiful, high mechanical strength, good electrical performance, anti-aging
-50~110℃ ultra-wide temperature control range, can be used in various temperature control fields, 0.1℃ temperature control accuracy, to meet your control needs
Wiring input and output design, more convenient to use in various industrial control equipment, multi-strand wire 300V/20A excess configuration, safe and reliable
Specification:
Product name: Microcomputer temperature controller
Product Model::XH-W3002
Temperature measurement range: -50~110℃
Temperature control range: -50~110℃
Temperature measurement accuracy: ±0.2℃
Temperature control accuracy: ±0.1℃
Measurement input: NTC10K L=1 meter waterproof probe
Input power: 12/24/220V
Output power: 120/240/1500W
output type: direct output
Output capacity: max 10A
Installation hole distance: 73mm (diameter 4mm)
Appearance size: 60*45*31mm
Product name: Microcomputer temperature controller
Product Model::XH-W3002
Temperature measurement range: -50~110℃
Temperature control range: -50~110℃
Temperature measurement accuracy: ±0.2℃
Temperature control accuracy: ±0.1℃
Measurement input: NTC10K L=1 meter waterproof probe
Input power: 12/24/220V
Output power: 120/240/1500W
output type: direct output
Output capacity: max 10A
Installation hole distance: 73mm (diameter 4mm)
Appearance size: 60*45*31mm
Set using:
Code and function introduction
P0 set startup temperature
Press the setting button once to enter the internal menu, the default display is P0, press the setting button again, and set the required startup temperature by pressing the up and down buttons.
P1 set stop temperature
Press the setting button once to enter the internal menu, the digital display is P0, switch to P1 by pressing the up and down buttons, press the setting button again, and set the desired stop temperature by pressing the up and down buttons.
P2 Set temperature correction
Enter the internal menu in the same way, switch to P2 by pressing the up and down buttons, press the setting button again, and set the required calibration temperature by pressing the up and down buttons. In the setting, if the detected temperature value is 0.5°C higher than the actual temperature value, the calibration temperature to be set is -0.5°C. If the detected temperature value is 1°C lower than the actual temperature value, the calibration temperature to be set is 1°C. Detected temperature±corrected temperature=actual temperature.
P3 set delay start
Enter the internal menu in the same way, switch to P3 by pressing the up and down keys, press the setting key again, and set the required delay time (unit is minutes) by pressing the up and down keys. Delay start is generally used for compressor refrigeration. If it is used for refrigerator freezers, this value needs to be set. According to the size of the compressor back pressure, the general setting value is 3-6 minutes. If you are not used to control the compressor or do not need delay time function, skip this item directly.
Code and function introduction
P0 set startup temperature
Press the setting button once to enter the internal menu, the default display is P0, press the setting button again, and set the required startup temperature by pressing the up and down buttons.
P1 set stop temperature
Press the setting button once to enter the internal menu, the digital display is P0, switch to P1 by pressing the up and down buttons, press the setting button again, and set the desired stop temperature by pressing the up and down buttons.
P2 Set temperature correction
Enter the internal menu in the same way, switch to P2 by pressing the up and down buttons, press the setting button again, and set the required calibration temperature by pressing the up and down buttons. In the setting, if the detected temperature value is 0.5°C higher than the actual temperature value, the calibration temperature to be set is -0.5°C. If the detected temperature value is 1°C lower than the actual temperature value, the calibration temperature to be set is 1°C. Detected temperature±corrected temperature=actual temperature.
P3 set delay start
Enter the internal menu in the same way, switch to P3 by pressing the up and down keys, press the setting key again, and set the required delay time (unit is minutes) by pressing the up and down keys. Delay start is generally used for compressor refrigeration. If it is used for refrigerator freezers, this value needs to be set. According to the size of the compressor back pressure, the general setting value is 3-6 minutes. If you are not used to control the compressor or do not need delay time function, skip this item directly.
Package include:
1x Thermostat
1x Thermostat
ST3012
Feature:
1.Double display dual temperature control design, a dual-purpose machine, set two sets of temperatures, high performance, temperature control performance and accuracy are very prominent.
Simple control panel design, wide temperature control range, simple setup, generous appearance and reliable quality.
2.Celsius Display, 2 Channel Relay output, Switch Between Cooling and Heating Modes
3.Temperature Measuring /Control Range: -50 to 110℃
4.With waterproof NTC 10K senor
Specification
Material: ABS + Electronic components
Temperature Measuring Range: -50 ~ 110℃
Temperature Control Range: -50 ~ 110℃
Temperature measurement accuracy: ±0.5℃
Temperature control accuracy: ±0.1℃
Input measurement: NTC10K Probe ，L = 1 meter，waterproof
Supply Voltage: DC 12/24/220V
Output Type: Relay Output(Output Switch)
Data preservation: Yes
Working Temperature: 0 to 50℃
Storage Temperature: -10 to 60℃
Material: ABS + Electronic components
Temperature Measuring Range: -50 ~ 110℃
Temperature Control Range: -50 ~ 110℃
Temperature measurement accuracy: ±0.5℃
Temperature control accuracy: ±0.1℃
Input measurement: NTC10K Probe ，L = 1 meter，waterproof
Supply Voltage: DC 12/24/220V
Output Type: Relay Output(Output Switch)
Data preservation: Yes
Working Temperature: 0 to 50℃
Storage Temperature: -10 to 60℃
List
1 x Dual Digital Display Temperature Controller
1 x Dual Digital Display Temperature Controller
STC-1000
Features
1. 100% brand new and high quality product.
2. Made of high quality materials, durable and practical.
Specification
Name: Digital display microcomputer temperature controller
Model：STC-1000
Measuring range: -50℃~99℃
Measurement accuracy: ±1℃(-50℃~70℃)
Resolution: 0.1℃
Overall power consumption: less than 3W
Sensor: NTC sensor (1m)
Ambient temperature: 0-60℃
Relative humidity: 20-85% (no condensation)
Installation opening: 71*29MM
Shell material: ABS flame retardant plastic shell
List
1 x Thermostat
STC-3008
Specification
Power supply: DC12V / DC24V / AC110V-220V
Measurement temperature range: -55°C ~ +120°C
Resolution: 0.1
Accuracy: ±1°C
Relay output contact capacity: heating: 10A/240VAC, cooling: 10A/240VCASensor h type: imported NTC sensor, line length 1 meter
Shell material: gray ABS flame retardant plastic shell
Measurement temperature range: -55°C ~ +120°C
Resolution: 0.1
Accuracy: ±1°C
Relay output contact capacity: heating: 10A/240VAC, cooling: 10A/240VCASensor h type: imported NTC sensor, line length 1 meter
Shell material: gray ABS flame retardant plastic shell
Set startup temperature:Press the "up" button once to display the starting temperature. Long press the "up" button for about 3 seconds,The required temperature can be set by the up and down keys
Set the stop temperature:Press the button once to display the stop temperature. Long press the button for about 3 seconds and the stop temperature number flashes. The required temperature can be set by the up and down keys
Press "Up 1" Button & "Up 2"Button at the same time to setting mode
Code Function Set Range Default
P0 Compressor 1 delay time 0-60min 0min
P1 Compressor delay time 0-60min 0min
P2 High temperature alarm value 55-120° C 120°C
P3 Low temperature alarm value 55-120° C -55°C
Code Function Set Range Default
P0 Compressor 1 delay time 0-60min 0min
P1 Compressor delay time 0-60min 0min
P2 High temperature alarm value 55-120° C 120°C
P3 Low temperature alarm value 55-120° C -55°C
How to restore factory Settings
Press the "Down 1" and "Down 2" button at the same time, the factory setting is restored
Press the "Down 1" and "Down 2" button at the same time, the factory setting is restored
List
1 x Temperature Controller
STC-3028
Specification
Relay output contact capacity: 10A
Integrated sensor, line length 1 meter
Shell material: gray ABS flame retardant plastic shell
Net weight 120g
Gross weight 140g
Relay output contact capacity: 10A
Integrated sensor, line length 1 meter
Shell material: gray ABS flame retardant plastic shell
Net weight 120g
Gross weight 140g
List
1 x Temperature Controller
1 x Temperature Controller
Am 05.09.2023 hat der Verkäufer die folgenden Angaben hinzugefügt: