*Compatibility Chart
1, You can distinguish specific model of an automobile by VIN(Vehicle Identification Number).

2, VIN(Vehicle Identification Number) consists of total 17 English letters and arabic digits.

3, VIN does not include the letters I (i), O (o), and Q (q) (to avoid confusion with numerals 1 and 0).

Lexus
GX460 Base Sport Utility 4-Door 4.6L 2010-2017
GX460 Executive Sport Utility 4-Door 4.6L 2013-2014
GX460 Luxury Sport Utility 4-Door 4.6L 2014-2017
GX460 Premium Sport Utility 4-Door 4.6L 2010-2017
GX460 Ultra Premium Sport Utility 4-Door 4.6L 2010-2011 2013-2014
GX470 Base Sport Utility 4-Door 4.7L 2003-2009

Toyota
4Runner Limited Sport Utility 4-Door 4.7L 2003-2009
4Runner Sport Sport Utility 4-Door 4.7L 2003-2009
4Runner SR5 Sport Utility 4-Door 4.7L 2003-2009

Land Cruiser Base Sport Utility 4-Door 4.7L 2004-2007
Land Cruiser Base Sport Utility 4-Door 5.7L 2008-2011 2013-2018
Land Cruiser VX Sport Utility 4-Door 5.7L 2008-2009
Land Cruiser VX-R Sport Utility 4-Door 5.7L 2017

*Relevant Introduction:

Lexus GX
GX 470 First generation (J120 2002-2009)

GX 460 Second generation (J150 2009-present)

Toyota 4Runner
Toyota Trekker (1981-1983)
N60 First generation (1984-1989)
N120 Second generation (1989-1995)
N130 Second generation (1989-1995)
N180 Third generation (1995-2002)
N210 Fourth generation (2002-2009)
N280 Fifth generation (2009-present)

Toyota Land Cruiser

Off-road oriented models

BJ/FJ First generation (1951-1955)

J20/J30 Second generation (1955-1960)

J40 Third generation (1960-1984)

J70 Fourth generation (1984-present)

Comfort oriented models

J50 First generation (1967-1980)

J60 Second generation (1980-1989)

J80 Third generation (1990-2008)

J100 Fourth generation (1998-2007)

J200 Fifth generation (2007-present)

Air Suspension Structure:

*Removal Guideline:
Caution: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.
1.To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.
2.Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.
1.Set steering to straight ahead.
2.Raise vehicle.
3.Remove the left rear wheel and fender well.(picture 1)

4.Remove the rear flap.(picture 2,3,4)

5.Remove the pump cover.(picture 5,6)

6.Disconnect the air line and filter hose.(picture 7,8)

7.Disconnect the lower electrical plug.(picture 9)

8.Loosen and remove the three bolts from the pump bracket.(picture 10,11,12)

9.Loosen and remove the pump filter bolts and remove the pump filter.(picture 13)

10.Loosen and remove the three compressor bracket bolts and remove the compressor from the bracket.(picture 14,15,16,17)

11.Disconnect the upper electrical plug.(picture 18)

12.Remove the air hose from the dryer.(picture 19)

13.Remove the bracket.(picture 20)

*Warning & Notice:

1.When the air compressor being replaced, the matching relay must be replaced according to the corresponding vehicle. If there is something wrong with the relay which leads the compressor to continuous operation without any break, it will burn out the electric motor or other plastic part.

2.When the air compressor being installed, the critical parts such as rubber shock pad and damping spring must be fully fixed on the stand without short installation or missing installation (The air compressor is unequipped with parts). With the anti-vibration parts of short installation or missing installation, a loud noisy instance will happen when the air compressor is working for the sake of resonance.

3.Distribution valve, shock absorber, air tank and tube connector must be checked after air compressor installed to ensure air-tightness. The lifespan of the air compressor will be shortened if the leakage exists.

4.Increased noises while the compressor is running may be caused by a non-functioning compressor mounting. Change the rubbers and springs of the mounting in any case.

5.A porous intake hose often is the cause for a breakdown of the compressor. Change the intake hose and preferably also the filter and noise absorber, because we do not want the compressor to breakdown because of these.

6.Change the relays before installing the compressor even if it seems to still work. This is also a specification by the car manufacturer. Be sure to change the right relays. Relays look similar, that is why there is a risk to change the wrong relays.

7.Be sure to check whether the system is leakproof after repairing. The easiest way to do this is to park the vehicle. Wait for the system to automatically re-adjust if your car has this feature. Then measure the heights from the ground to the lower edge of the fender as exactly as possible and take notes. On the day after measure these heights again and compare them with the ones before. Even a small difference will lead to a damaged compressor and damaged valves in the long run.

?

*OEM Part Number:

4891060042,4891060040,
4891060020,4891060021