Full Range of
Filtration Media, Strainer Cages and DIY Filter Related Products
Bio-Plas Media Key
Features
Bio-Plas Filter Medias are suitable for use in
mechanical and biological filtration systems.
All types of Bio-Plas filter media
provide large surface areas for good bacteria to colonise and this increases
the efficiency of a box, pressure or multi-bay pond filter.
Bio-Plas Medias provide the maximum
active surface area for the bacteria to colonise, much more than other types of
static media. It is this process which removes harmful ammonia and nitrite from
the water.
Within the media is a protected
surface which enables colonies of bacteria to naturally follow their lifecycle,
of maturing, dying and then fuelling the latter stages of the nitrification
cycle.
All Bio-Plas filtration media can be
used in either a mechanical or biological Filtration system; Bacteria will
colonies while collecting debris and plant material from the pond with no
compromise water flow.
Bio-Plas Micro is different from
other medias as it move within the filter and cause old dead bacteria on the
outside of the wheel to be displaced, leaving space for new bacteria to rapidly
develop.
Filter maintenance time can be
reduced by using Bio-Plas Micro, designed to freely move in a filter, this
movement causes the media to self clean as it turns unlike foam and static
filter media that require removing and cleaning. This self cleaning process
allows the filter to be effective without the disturbance caused by regular
cleaning as it avoids the unnecessary loss of vital bacteria.
The
Bio-Plas Range
All media in the Bio-Plas range are different in size, buoyancy and colour. Depending on the application and budget Bio-Plas will have a filtration media suitable for you.
All Bio-Plas Filtration Media is manufactured in
England
A Bio-Plas sack will be supplied with every individual 20
litre option
Litre of Media converted to a volume
20 liters = 20000cm3
100 liters = 100000cm3
1000 liters = 1000000cm3 (1 Cubic Meter)
HI-BLO Aerator
The Aqua-Jet Air Diffuser
HI-BLO Aerator has been specially developed for situations where a high
concentration of aeration is needed, whether this be for fluidized beds in your
filter system or out in the pond.
it is important to use a powerful air pump (depending on
the size of the filter bed)
Recommended Air pump Size: 40-60LPM (for
normal aeration situations)
Aerator Size: Dia-290mm
Supplied
with 10 meters of clear flexible P.V.C airline 6mmID
Drawstring Nylon Mesh Filter Bag
These filter media bags are designed for filtration applications. The bags hold carbon, ammonia remover resins or any other type of filter media.
Keep media in these bags to prevent fines from washing out.
These bags provide a convenient way to customise pond, tank and aquarium filtration.
Bio-Plas Filtration Sacks have
been designed for use with filtration media, each sack will neatly contain
20 liters of filtration media.
The
Filter Webb is one of the best products for polishing the water and for the
size of the Filter Webb the surface area it offers to catch micro-particles is amazing.
Super
easy to easy to clean, just pop the Filter Webb in to a clean bucket of water
and plunge up and down a few times and it will release the fine particles it
has trapped, repeat till the water is clean. Ideal in finishing Chambers.
This
Filter Webb works the same was as foam but better, not only does it offer more
filtration capability but due to its design it is really easy to clean all the
fibers/pours of the webb, unlike foam.
The
Filter Webb can be used as an added addition to your filter buy simply
installing a single Filter Webb or can be used in large numbers for whole
chambers
Filter
webb 300 = 300mm dia/100mm in depth
Filter webb 450 = 450mm dia/100mm in depth
Filter
Webb 300 are sold in a pack of 4
Filter
Webb 450 are sold in a pack of 2
Filter
Grid
The
Filter Grids are made of non-toxic polypropylene so are ideal to use as baffle
boards and filter media support trays, the open grid design allows a free flow
of water and will give excellent strength and support.
A
must if you are building your own Filtration system.
The
filter grid is easy to cut making it ideal if the user has a round
tank/filter
Filter
Grid size L 680mm x W 400mm x D 12mm
Multi
Grid
The
Multi Grid is a carefully designed clip-together Filter Grid that requires no
additional fastenings or fixtures but gives excellent strength and support.
Regardless
of the size of the application, the Multi Grid can be connected together to
make a grid to suit. Ideal for large baffle boards, filter media support trays
in filter systems and dividers in grow tanks the open grid design allows a free
flow of water.
A
must if you are building your own Filtration system.
The
Multi Grid is easy to cut making it ideal if the user has a round
tank/filter
Multi
Grid size L 300mm x W 300mm x D 12mm
6 Multi Grid will be
included (a combined size of 60cm x 90cm)
All Available in Clear - Manufactured from a transparent
Polymer, ideal for dividers in a tropical fish tank
Filter
grid Topper has been designed to reduce the grid size on the popular filter
grid.
The
original grid size is 18mm x 18mm; the addition of the Grid Topper kit will
reduce the grid size down to 7mm x 7mm.
This
is ideal if you are using a small/fine media in your systems
One
Grid Topper kit is meant for one filter grid (680mm x W 400mm x D 12mm) the
Grid Topper kit sits just shy of the outside edge of the grid
The
kit is supplied with 5 Grid Toppers (130mm x 383mm) and 10 pairs of Clips. The
kit will have to be assembled once arrived
The
clips come in two halves that simply push/snap together, please note once the
clips have been secured to each other they are not designed to come apart and
you risk breaking them.
The strainer will stop large debris from going
into the actual filter. The strainer has been designed to be attached to any
110mm/4” fitting; the strainer cage is manufactured with a joining spigot of
110mm OD. All 110mm/4” fittings such as bends and tees will mount directly onto
the strainer itself (if you require any further information on sizing please
look at our pipe identification chart supplied)
The strainer can also prevent fish
from disappearing through the pipework.
This strainer is also perfect for
using in-between ports/inlets in your filter. Stopping any media from leaving
its intended chamber.
The strainer has been designed to be
cleaned/maintained easily. Simply remove the 4 threaded nuts from the top plate
of the strainer; this will give access to the inside.
The range of strainer cages are supplied
with a range of different fittings to suite most requirements, please select
the configuration that is required from the drop down menu.
Please
Note: This fitting is solvent weld
Large
Rectangle Cage
Size: H-155mm W-200mm L-240mm
Large
Round Cage
Size: H-160mm Dia – 280mm
Due
to popular demand, the large Multi Strainer cage has been brought to the
market. The multi-strainer enables two or more strainer cages to be joined
together. Ideal for large filter beds or grow tanks. The connectors of each
strainer simply push together; the addition of a non-toxic solvent weld
adhesive will ensure a permanent fit
Please
note: 1 Multi Strainer will be included but will need the addition of one of
the large round strainer kits
The
strainer has been designed to be attached to any 2”/56mm rigid pipe, with the
addition of a removable nut. This allows for a secure/tight fit but is easy to
clean by just unthreading the nut
This
strainer is also perfect for using in-between ports/inlets in your filter.
Stopping any media from leaving its
intended chamber in filters such as moving beds.
This
strainer will fit any 2”/56mm (OD) pipe work or fittings
The
small strainer cage is supplied in several different configurations to suite
most requirements
The
removable strainer/cage from a 2″/56mm threaded tank connector kit comes
with all the necessary parts to connect your strainer to a tank/filter box.
The
kit will come supplied with the removable strainer, 56mm-56mm internal joiner
and a 56mm threaded tank connector. (Please refer to our thread tank connector
chart for more information on dimensions)
The
kit will come unassembled so this enables the customer to choose a
configuration appropriate for the application that they need. The 56mm threaded
tank connect has a double socked design enabling it to receive rigid
pipe/fittings on either side.
The
removable strainer/cage from a 2″/56mm threaded tank connector and 43mm
hosetail kit comes with all the necessary parts to connect your strainer
to a tank/filter box. from a flexi hose feed/return
The
kit will come supplied with the removable strainer, 56mm-56mm internal joiner
56mm threaded tank connector,56mm-43mm reducing bush and a 43mm hosetail
This hosetail can be
used in-conjunction with flexible hose with an internal diameter (ID) of 20mm
(3/4″) -25mm (1″) 32mm- (1.25″) 38mm-(1.5″) flexi hose.
The
removable strainer/cage from a 2″/56mm threaded tank connector and 50mm
hosetail kit comes with all the necessary parts to connect your strainer
to a tank/filter box. from a flexi hose feed/return
The
kit will come supplied with the removable strainer, 56mm-56mm internal joiner
56mm threaded tank connector,56mm-50mm reducing bush and a 50mm hosetail
This hosetail can be
used in-conjunction with flexible hose with an internal diameter (ID) of
30mm-40mm-50mm
Strainers
are ideal for any inlet or outlet pipe work on filters. The strainer will stop
large debris from going into the actual filter. The strainer has been designed
to be attached to any 2”/56mm rigid pipe, with the addition of a removable nut.
This allows for a secure/tight fit but is easy to clean by just unthreading the
nut
The
double strainer was designed for larger ponds/filter systems where a larger
flow of water is required.
This
kit has not been assembled allowing you to build it in different configurations
tailor made to your filter/pond setup.