SAFE & SECURE SHOPPING
100% SATISFACTION GUARANTEED
FAST SHIPPING
FPV AIO F4 1S F411 Racing RX for 12A MPU6000 Brushless Drone BETAFPV ELRS 2.4G

Product Description

F4 1S 12A AIO Brushless Flight Controller V2.2 is the default FC forCetus X brushless whoop quadcopter, also great for 85mm whoop drones likeMeteor85and 3" toothpick drones like HX115 SE Toothpick Drone and HX115 LR Toothpick Drone. We updated the FC to V2.2 with BMI270 gyro and BB51 ESC hardware in place of ICM20689 gyro and BB21 ESC hardware.

F4 1S 12 AIO SPI Frsky V1.2 is coming soon. Please stay tuned for it.

Please click here to page F4 1S 12A AIO ELRS V2.0 if you need information about it.

Tons of ExpressLRS items are available now!

Bullet Point

  • F4 1S 12A AIO Flight Controller is the best choice for building ultra-lightweight 3" toothpick drones like HX115 SE FPV Quad and 85mm whoop drones. Recommend Meteor85.

  • Most of the 1S flight controllers on the market come with 5A ESC by now, but this FC especially integrates 1S 12A ESC, providing more sufficient power for 3" toothpick drones or 85mm whoop drones.

  • Built-in current meter, 2 programmable RGB LEDs, and SPI ELRS or Frsky receiver. At the same time, all the pads are left for the external receivers with UART1 and UART2, for buzzers, etc.

  • Large pads are reserved for solder motor cables, this design will make solder easier.

Specification of FC

  • Item: F4 1S 12A AIO FC

  • Weight: 4.74 g (without power cable and BT2.0 connector)

  • CPU: STM32F411CEU6 (100MHZ )

  • Six-Axis: BMI270 (SPI connection)

  • Firmware version: betaflight_4.3.1_BETAFPVF4SX1280

  • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)

  • Receiver: SPI ELRS 2.4G Receiver

  • Motor Pin Connector: 1.25mm Header Pins

  • Mounting Hole Size: 26mm x 26mm (suitable for whoop pattern mounting hole)

  • USB Port: SH1.0 4-Pin

Specification of 1S 12A ESC

  • Built-in ESC with 12A continuous and peak 25A current

  • Input voltage: 1S-2S

  • ESC firmware: C_X_30_REV16_7_20220802.hex for BB51 BLHeli_S hardware

  • Signal support: D-shot150, D- shot300, D-shot600, Oneshot125, Multishot, PWM

The BLHeli_S firmware could support the BB51 hardware now. This V2.2 board is powered by BB51 hardware.If you want to setup the ESC specification, please update to the newest BLHeliSuite-16714902a first.

Download the newest BLHeliSuite-16714902a here.

Download the BB51 ESC firmware C_X_30_REV16_7_20220802.hex

Note: BetaFlight Configurator, BLHeli Configurator, and Bluejay Configurator are invalid for the BB51 ESC now.

Diagram for F4 1S 12A AIO FC

Below is the diagram for ELRS 2.4G V2.2 board.

The current meter is integrated on the FC board. Here is the configuration in Betaflight Configurator.

12A 1S ESC

Should we really need a 12A ESC for 1S drones? If it is a 65mm or 75mm Whoop drone-likeMeteor65, 5A ESC is enough for all actions. But how about with 3" propellers and 1102/1202.5 motors? Still, want smooth and powerful flying actions? The 5A ESC has developed about 3 years ago and was designed for whoop drones with 0603/0802 motors. For the past year, the BETAFPV team has been cooperating with BLHeli author Steffen on the 12A 1S ESC for 3" toothpick drones. Finally, it is here!

SPI ELRS 2.4G RX

This board integrates the receiver with the most popular radio link ExpressLRS since 2021. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. Know more about the ExpressLRS project on Github or join the discussion in the Facebook Group.

This board is designed for long-range 3inch ultralight toothpick drones or 2S whoop drones. If you want to try ExpressLRS on 65mm/75mm whoop drones, please build it with ourF4 1S FC board with a built-in SPI ExpressLRS receiver.

F4 1S 12A AIO V2.2 integrates SPI ELRS 2.4G RX. The configuration is as follows.

How to Bind with Betaflight FC with SPI ExpressLRS Receiver.

How to Bind with Betaflight FC with External ExpressLRS Receiver.

More details and discussion on Github about SPI ELRS receiver.

SPI Frsky RX

Come with the built-in SPI Frsky Receiver (CC2500 chip), F4 1S 12A AIO FC can be compatible with Futaba S-FHSS, Frsky D8, and D16 protocol. The default protocol is configured to Frsky D16 FCC out of the factory. Pilots could set up the protocol according to your own need in Betaflight Configurator.

Configuration

Protocol

FRSKY_D

Frsky D8

FRSKY_X

Frsky D16 FCC (ACCST 1.X version)

FRSKY_X_LBT

Frsky D16 LBT (ACCST 1.X version)

SFHSS

Futaba S-FHSS


How to Bind with Betaflight FC with SPI Frsky Receiver.

Betaflight Firmware and CLI

F4 1S 12A AIO SPI ELRS 2.4G comes with the default firmware betaflight_4.3.1_BETAFPVF4SX1280, which supports ELRS V2.0 only. We update the gyro to BOSH BMI270 since the V2.2 version. 

Pay attention,ONLY the newest Betaflight firmware 4.3.1 start to support this BMI270 gyrometer. Please check the below link to download the firmware.

Download the firmware and CLI dump file for the F4 1S 12A FC (ELRS 2.4G) V2.2 board.

Recommend Parts

If you want to try the popular ExpressLRS receiver version for long-range performance, highly recommend you check the items for the ExpressLRS series.

Package

  • 1 * F4 1S 12A AIO FC

  • 4 * Anti-vibration Rubber Dampers

  • 4 * M2 x 10mm Screws

  • 4 * M2 x 10mm Screws

  • 4 * M2 Screw Nut

  • 8 * PH-1.25 Connectors for Motor

  • 1 * SH1.0 4-Pin Cable

  • 1 * SH1.0 4-Pin to USB Type-C Adapter







 Welcome to our store, we are doing FEICHAO brand products, our factory mainly do the metal parts of the camera accessories, the price is the factory price, wholesale price, we have a large number of inventory shipments fast, the need for large quantities of wholesale can contact me, I can give you the highest discount price!

1. All price does not include any taxes or extra fees. We are not responsible for the problems caused by customs clearance. 

2. Orders processed timely after the payment verification.

3. We only ship to confirmed order addresses. Your order address MUST MATCH your Shipping address. 

4. The images shown are not the actual item and are for your reference only. 

5. SERVICE TRANSIT TIME is provided by the carrier and excludes weekends and holidays. Transit time may vary, particularly during the holiday season. 

6. If you have not received your order after the Estimated Delivery of Shipping Method, please contact us in advance. We will trace your order and get back to you asap.

(Please notice that we can't decide your decisions about choosing to ship methods, which means you need to check carefully with the estimate delivery time and promise delivery time) Your satisfaction is our top priority!


1. You have 30 days to contact us  No reason to return within 30 days after signing，The shipping cost is Seller . 

2. All returned items MUST BE in the original packaging and you MUST PROVIDE us with the shipping tracking number, specific reason for the return, and your order ID. 

3. We will refund YOUR FULL WINNING BID AMOUNT, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER BOTH Buyer and Seller cancel the transaction from ebay. OR, you may choose to have a replacement. 

4. We will bear all the shipping cost if the product(s) is (are) not as advertised.


We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important. We request that you contact us immediately BEFORE you give us neutral or negative feedback so that we can perform up to your satisfaction. 

It is impossible to address issues if we do not know about them!

Copyright © 2022 Tongtool