3300W Nass Trocken Kernbohrgerät 165mm Kernbohrmaschine + Standfuß Set 800U/min
Product Description
Our Core Drilling Machine Combines Functionality and Versatility in One Device. It Is Ideal for Lighter Drilling Work.
Feature
Water Connection with Hose Approx.6m
Non Water Seal Cage Reduce Maintenance Costs
Aluminum Alloy Material Ligher and Steadier
Max. Drilling Diameter 165mm
Suitable for Sampling Concrete, Cement, Brick, Bituminous Pavement and Block
Specifications
Color: Red
Rated Input Power: 3300w
Rated Voltage:220v
Rated Frequency: 60hz
The Largest Drilling Capacity: 6.5 Inch
No-load Speed: 800r/Min
Spindle Thread：m22（22mm）
It Fit M22 Drill Bit( Sale Separately)
The Spindle Thread Is Not 1 1/4“!!!
Installation:
First, Install the Screw Connecting the Stand and the Pedestal. Before Use the Drill, You Need to Fix It.
1. Remove the Two Screws on the Back of the Stand;
2. Seperate the Stand and the Pedestal;
3. Rotate the Pedesta 180° and Install the Screws.
Feature
Water Connection with Hose Approx.6m
Non Water Seal Cage Reduce Maintenance Costs
Aluminum Alloy Material Ligher and Steadier
Max. Drilling Diameter 165mm
Suitable for Sampling Concrete, Cement, Brick, Bituminous Pavement and Block
Specifications
Color: Red
Rated Input Power: 3300w
Rated Voltage:220v
Rated Frequency: 60hz
The Largest Drilling Capacity: 6.5 Inch
No-load Speed: 800r/Min
Spindle Thread：m22（22mm）
It Fit M22 Drill Bit( Sale Separately)
The Spindle Thread Is Not 1 1/4“!!!
Installation:
First, Install the Screw Connecting the Stand and the Pedestal. Before Use the Drill, You Need to Fix It.
1. Remove the Two Screws on the Back of the Stand;
2. Seperate the Stand and the Pedestal;
3. Rotate the Pedesta 180° and Install the Screws.
4. Install Completed
Fix the Driller:
Here Are Two Ways
1．Using Expansion Link
Choose a Hollow Tube According to the Height of the Place Which Need to Be Drilled. Put One End of the Tube Against the Adjustable Screw Rod. and Turn the Rod Reversely to Fix the Driller Tightly, Expansion Bolts Are Not Needed.
2．Using Ecpansion Bolt
Make a Hole on the Wall or the Groud and Install the Bolt;
Expand the Bolt;
Install the Screw Rod and the Stand. Then Tighten the Nut.
Install Drill Bit
Before Installing, You Need to Smear some Grease on the Drill End Thread in Order to Discharge Easily. After Instlling, You Need to Run the Driller at an Idle State at First.
Attention: Before You Install or Remove the Drill Bot, You Must Be Sure the Drill Is Powered off. Before Running, the Drill Must Be Connected with Clean Cold Water.
Here Are the Ways to Inject Water:
1. Using Tap Water: Connecting the Tap and the Machine with the Injecting Hose.
2. Hanging a Bucket over the Drill
3. Using Water Pump
4．Drilling
Start the Drill at an Idle State. Then Open the Water Tap. When There Is Water Flowing from the Drill, You Can Start Drilling. at First, You Need to Drill Slowly and Increase Strength Gradually. After You Drill Deeper than 5mm, You Can Increase Your Push Strength. If the Drill's Rotating Speed Decrease, than Proves That the Drill Is Overloaded. Then You Need to Decrease the Push Strength, Avoiding the Drill Being Stuck. If There Is Smoke Coming out, You Must Pull out the Drill Right Away and Start to Drill After a While, Avoiding the Engine Being Burn down.
5．Material Being Drilled
When Drilling Reinforced Concrete, Current Increases and the Drill Will Vibrate. Therefore, You Need to Decrease Pushing Strength but the Decreasing Amplitude Should Not Be Too Big. Otherwise, the Effiency Will Be Affected and the Drill Bit Will Be Worn More Badly. When Drilling Reinforced Concrete Containing Little Grains of Sand and Small Stones, the Drill May Be Overloaded Suddenly and the Drill Be Powered off Automatically. at This Time, You Need to Pull out the Drill Right Away and Clean the Hole You Drilled Before You Start Again. When You Drill Woof Board and Thick Pitch, You Also Need to Decrease Pushing and Drill Slowly.
6．Taking out Drill Core
When You Are Going Yo Drill Through the Board or Wal, You Need to Slow down, Avoiding the Drill Bit Being Stuck. If the Drill Bit Is Stuck, You Need to Power off the Drill Immediately Pull out the Bit and Clean It. Fetch out the Drill Core. Install the Drill Bit and Start Again.
Attention: You Should Be Careful When Taking out the Drill Bit, Noting Damaing It.
7．the Drill Vibrate
The Drill Vibrate When It Is Working.it May Be Because the Distance Between the Racks Connecting the Lifting Body and the Stand Is Too Big. Then You Need to Tighten the Screws to Adjust the Distance. at the Same Time, You Need to Make Sure That the Pedestal and the Stand Is Connected Firmly.
Application:
This Drill Can Be Used on Brick, Stone, Reinforced Concrete, Rock, and Fireproof Materials.
Here Are Two Ways
1．Using Expansion Link
Choose a Hollow Tube According to the Height of the Place Which Need to Be Drilled. Put One End of the Tube Against the Adjustable Screw Rod. and Turn the Rod Reversely to Fix the Driller Tightly, Expansion Bolts Are Not Needed.
2．Using Ecpansion Bolt
Make a Hole on the Wall or the Groud and Install the Bolt;
Expand the Bolt;
Install the Screw Rod and the Stand. Then Tighten the Nut.
Install Drill Bit
Before Installing, You Need to Smear some Grease on the Drill End Thread in Order to Discharge Easily. After Instlling, You Need to Run the Driller at an Idle State at First.
Attention: Before You Install or Remove the Drill Bot, You Must Be Sure the Drill Is Powered off. Before Running, the Drill Must Be Connected with Clean Cold Water.
Here Are the Ways to Inject Water:
1. Using Tap Water: Connecting the Tap and the Machine with the Injecting Hose.
2. Hanging a Bucket over the Drill
3. Using Water Pump
4．Drilling
Start the Drill at an Idle State. Then Open the Water Tap. When There Is Water Flowing from the Drill, You Can Start Drilling. at First, You Need to Drill Slowly and Increase Strength Gradually. After You Drill Deeper than 5mm, You Can Increase Your Push Strength. If the Drill's Rotating Speed Decrease, than Proves That the Drill Is Overloaded. Then You Need to Decrease the Push Strength, Avoiding the Drill Being Stuck. If There Is Smoke Coming out, You Must Pull out the Drill Right Away and Start to Drill After a While, Avoiding the Engine Being Burn down.
5．Material Being Drilled
When Drilling Reinforced Concrete, Current Increases and the Drill Will Vibrate. Therefore, You Need to Decrease Pushing Strength but the Decreasing Amplitude Should Not Be Too Big. Otherwise, the Effiency Will Be Affected and the Drill Bit Will Be Worn More Badly. When Drilling Reinforced Concrete Containing Little Grains of Sand and Small Stones, the Drill May Be Overloaded Suddenly and the Drill Be Powered off Automatically. at This Time, You Need to Pull out the Drill Right Away and Clean the Hole You Drilled Before You Start Again. When You Drill Woof Board and Thick Pitch, You Also Need to Decrease Pushing and Drill Slowly.
6．Taking out Drill Core
When You Are Going Yo Drill Through the Board or Wal, You Need to Slow down, Avoiding the Drill Bit Being Stuck. If the Drill Bit Is Stuck, You Need to Power off the Drill Immediately Pull out the Bit and Clean It. Fetch out the Drill Core. Install the Drill Bit and Start Again.
Attention: You Should Be Careful When Taking out the Drill Bit, Noting Damaing It.
7．the Drill Vibrate
The Drill Vibrate When It Is Working.it May Be Because the Distance Between the Racks Connecting the Lifting Body and the Stand Is Too Big. Then You Need to Tighten the Screws to Adjust the Distance. at the Same Time, You Need to Make Sure That the Pedestal and the Stand Is Connected Firmly.
Application:
This Drill Can Be Used on Brick, Stone, Reinforced Concrete, Rock, and Fireproof Materials.
Hinweis: M22 Bohrer und Bohrer sind nicht im Lieferumfang enthalten
===========
Note: M22 drill bit and drill barrel are not included
===========
Note: M22 drill bit and drill barrel are not included
Nachdem Sie bestellt haben, müssen Sie innerhalb 7 Tage bezahlen
Normalerweise senden wir die Ware als ein Geschenk an Sie, indem Sie keinen Zollgebühren bezahlen können. Der Gebühren ist wie Import Steuern, der Kaufpreis und die Versandkosten enthalten nicht Zollgebühren. der Käufer ist für dies verantwortlich
Normalerweise senden wir die Ware als ein Geschenk an Sie, indem Sie keinen Zollgebühren bezahlen können. Der Gebühren ist wie Import Steuern, der Kaufpreis und die Versandkosten enthalten nicht Zollgebühren. der Käufer ist für dies verantwortlich
Bitte beachten Sie sich bei Zahlung via Vorkasse: Erfahrungsgemäß dauert eine Überweisung je nach Bank 2-3 Tage, bis das Geld überwiesen ist.
Sobald Ihre Zahlung eingegangen ist, schicken wir Ihnen die Ware innerhalb 48 Stunden los.
Am Samstag und Sonntag erfolgt keine Zustellung und kein Versand.
Großhandel an Sie Rabatt Preise ，Herzlichen Willkommen bei uns einkaufen!!
3-7 Tage : DEUTSCHLAND
5-10Tage :Andere Länder
Wir versprechen, dass jeder Artikel losgeschickt hat. Aber machmal gibt es auch 0.3% Paket während transportieren zu verloren. Wenn dies passiert, nachdem wir dies mit dem Post bestätigt haben, werden wir Ihnen das Paket so schnell wie möglich nochmal schicken oder erstatten Ihnen sofort das Geld zurück.
Unsere alle Ware sind Original und neu. Bevor wir Ihnen die Ware losschicken, werden wir die Ware absolute prüfen. unseres Ziel ist, lassen Sie zufrieden sein.
Wenn Sie die Ware nicht mögen und die uns zurücksenden möchten, sehen Sie bitte unten:
Bevor Sie uns die Ware zurückgesandt haben, sagen Sie bitte uns zu ersten, dann werden wir Ihnen unsere Retourschein. bitte senden Sei uns die Ware innerhalb 3 Tage zurück, nachdem Sie die Ware erhalten haben
bitte bestätigen Sie，die Ware wie original einpacken. und Sie sollen auch die Rücksendungskosten tragen
Nachdem wir das Paket von Ihnen bekommen und geprüft haben, werden wir Ihnen das Geld so schnell wie möglich zurückerstatten.
Wenn die Ware während transportieren gebrochen haben, können Wir Ihnen das Geld zurückerstatten, nachdem wir die Ware wieder bekommen haben, oder tauschen wir Ihnen eine neue Ware um. Aber bitte vergessen Sie nicht uns einige deutliche Fotos zu schicken
Dank für den Kauf von meinem Geschäft.
Wenn Sie irgendein Problem mit dem Einzelteil, wenn Sie es erhalten haben, bitte zögern Sie nicht, mit uns Kontakt aufzunehmen.
Wir bieten Ihnen die beste Lösung für jedes Problem mit dem Einzelteil.
Wir würden uns freuen, wenn Sie uns freundlich in Verbindung, bevor uns eine Rücknahmeverlangen oder Verlassen negatives Feedback.
freundliche Grüße
Arbeitszeit : Montag bis Freitag 8:30 AM bis 5:00 PM (Beijing Zeit)
Wegen des Zeitunterschied können vielleicht wir ihre Frage nicht rechtzeitig antworten. Aber in unserem Arbeitstag, werden wir ihre Email innerhalb 24 Stunden antworten. Im Wochenende sein Sie bitte so nett und warten geduldig bis am Montag. Vielen dank!
Bitte schreiben Sie uns an Ebay Message.
Sollten noch weitere Fragen auftreten, bitte zögern Sie nicht mit uns in Kontakt zu treten, wir sind gerne bereit Ihnen zu helfen, um zu einem befriedigenden Resultat zu kommen.
