Motorized ball valves offer an energy-efficient alternative to solenoid valves, especially for prolonged positioning. They mainly consume energy during opening and closing, with negligible amounts once fully opened. This allows for permanent connection without the risk of overheating or burning out. This valve comes in stainless steel. It is 1” in diameter, and is full port. This means the diameter of the opening in the ball is a full 1”. If you are using this for a system where pressure is important, or with mixed materials, where restrictions on flow can lead to the separating of the material, a full-bore ball valve is your best option. These valves are not intended for situations where fast action closing or opening is needed, as they do take a few seconds to fully open and close. DC: Connect the yellow wire to the negative pole(-). The valve will open when the red wire is connected to the positive pole(+), and close when the blue wire is connected to the positive pole(+). Disconnecting any wire will maintain the valve's current state. AC: Connect the yellow wire to any pole. The valve will open when the red wire is connected to the other pole, and close when the blue wire is connected to the other pole. Disconnecting any wire will maintain the valve's current state. Meticulously tested and performance-rated parts ensure quality. With a lifespan of up to 100,000 cycles, the valve operates in 3-5 seconds; higher voltage enables quicker opening and closing. The robust 2Nm torque in the stem, often overlooked, is crucial for enduring serious torque without failure. This motorized ball valve features standard NPT threading, commonly used in U.S. piping. The tapered threading enhances connection sealing, requiring pipe thread tape for installation. Meticulously manufactured and tested, ensuring precise threading for straightforward installation. Apply pipe thread tape tightly to the male pipe end to facilitate a secure connection. Screw tightly into the valve to maintain a leak-free connection throughout its lifespan. What is the Waterproof Rating of this valve? The motor's housing is rated at IP65 for ingress protection. If permanently installed outdoors, it is recommended to place it under a shelter or in a protective box to prevent prolonged exposure to rain. For more details, please refer to Picture 1. What is the difference between N.C. (Normally Closed) and N.O. (Normally Open) ? In a N.C. valve, it's closed without power and opens when energized. Conversely, in a N.O. valve, it's open without power and closes when energized, blocking fluid or gas flow. For more details, please refer to Picture 2. What is the difference between Full Port and Standard Port? In a full port valve, the internal diameter of the valve is the same as the pipe it's connected to. In a standard port valve, the internal diameter of the valve is smaller than the pipe size. For more details, please refer to Picture 3. Can this be used for Drinking Water? YES. The motorized ball valve is made of lead-free stainless steel and is NSF certified. About '2 wire auto return', '2 wire reverse polarity', '3 wire', '3 wire 1-Way Setup' and '5 wire'. For more details, please kindly refer to Picture 4. Included below are the wiring schematics for all four setups mentioned before. These schematics provide a more formal presentation of wiring options for your valve. Please note that there are various possible ways to wire your motorized ball valve. Product Description
Port Size 1" NPT (Full Port) Valve Material Stainless Steel Close/Open Time 6-8 Seconds Working Voltage 9-24V AC/DC Max Power 5 W Max Torque 6 N m Max. Pressure 145 PSI (1.0 Mpa) Temperature Range Medium Temp: 32℉ to 194℉; Ambient Temp.: 14℉ to 104℉
Applicable Medium Water Life Expectancy 80,000-100,000 Cycles Flow Aperture 0.98 inch (25 mm) Normally Open/Closed Normally Closed Auto Return NO Waterproof Rating IP65 Wiring 3 wire Seal PTFE
U.S. Solid Motorized Ball Valve
1" SS Ball Valve with Full Port, 9-24V AC/DC and 3 Wire
Wiring your new Motorized Ball Valve
3 Wire
Cherished by DIY Community, Approved by Engineers
Precision Threading
How to Install the Motorized Ball Valve?
Wiring Schematics
1" Motorized Ball Valve
$59.84$59.84 $53.69$53.69 $45.88$45.88 $69.81$69.81 $64.83$64.83 $66.83$66.83 $64.83$64.83 Stainless Steel Stainless Steel Brass Stainless Steel Brass Stainless Steel Stainless Steel Full Port Full Port Standard Port Full Port Standard Port Full Port Full Port ✘ ✔ ✘ ✔ ✔ ✔ ✘ 9-24V AC/DC 9-24V AC/DC 9-24V DC 9-24V AC/DC 85-265V AC 9-24V AC/DC 9-24V DC 3 wire 2 wire,auto return 2 wire,reverse polarity 2 wire,auto return 2 wire,auto return 2 wire,auto return 2 wire,reverse polarity ✘ ✘ ✘ ✔ ✘ ✘ ✘ Normally Closed Normally Closed Normally Closed Normally Closed Normally Open Normally Open Normally Closed
Item model number | USS-MSV00003 |
Inlet Connection Type | National Pipe Tapered |
Power Source | AC/DC |
Batteries Included? | No |
Specification Met | nsf certification |
Batteries Required? | No |
Finish | Stainless Steel |
Material | Stainless Steel |
Is Discontinued By Manufacturer | No |
Package Dimensions | 4.37 x 4.02 x 3.54 inches |
Item Package Quantity | 1 |
Item Weight | 1.65 pounds |
Number of Ports | 2 |
Exterior Finish | Stainless Steel |
Valve Type | Ball Valve |
Part Number | USS-MSV00003 |
Color | Steel |
Wattage | 2 watts |
Shape | Rectangle |
Voltage | 12 Volts |
Size | 1 Inch |
Shipping
Returns and payment
FeedBack
For any questions, using eBay contact system