• Early Warning of Impending Earthquake :Get an early warning of impending earthquakes with this detector, giving you time to prepare for the disaster.


• Quake Alarms :The quake alarms alert you when an earthquake is happening, ensuring that you take the necessary steps to stay safe.


• Suitable for Home and Office :This detector is perfect for both homes and offices, making it a versatile tool for disaster preparedness.


• Easy to Install :With its simple installation process, you can easily set up this detector in your home or office without any hassle.


P-WAVE SEISMIC ALARM, FOR MORE INFORMATION PLEASE CONTACT US, MOUNTING INSTRUCTION

CHOOSING A LOCATION

Your Earthquake Detector can be mounted in various locations depending on your personal needs.One good location is in or near a bedroom where it will wake you up and provide an instant alert to allow you to take shelter or tend to other family members.Your Earthquake Detector can be mounted behind curtains,beside a night stand or a hallway. It can also be mounted in general living areas such as living rooms and dens.

NOTE: When choosing a location, it is best if the Earthquake Detectoris located away from doors due to the vibrations caused when a door is being closed. Greater sensitivity can be achieved when the Earthquake Detectoris mounted on a firm wall or over a stud location on a load bearing wall. If there are small children in the household, it is recommended that the Earthquake Detector be mounted out of their reach.

-1-

The Earthquake Detector mounts on the wall with the use of the Velcro strips on the back of the unit. Hold the unit against the wall to see how the PENDULUM(seen through the adjustment window) swings back and forth as you move the Earthquake Detector. When properly installed, the PENDULUM should be in the center of the ARIANGULAR CONTACT.(NOTE: Wall must be clean and dust free for the Velcro strips to stick..)

  1. Peel away the white protective covering on the back of the Velcro strips.

  2. Position the Earthquake Detector about half an inch away from the mounting location that you have chosen (stright out from the wall).

  3. While looking through the ADJUSTMENT WINDOW,align the PENDULUM in the middle area of the TRIANGULAR CONTACT.

  4. While keeping the PENDULUM in the middle area of the TRIANGULAR CONTACT,

-2-

SLOWLY move the Earthquake Detector toward the wall until the Velcro strips make contact with the wall,then firmly press the Earthquake Detectoragainst the wall for the adhesive to stick to the wall.

  1. To center the PENDULUM from front to back (within the TRIANGULAR CONTACT), rotate the SENSITIVITY ADJUSTMENT SCREW clockwise or counter clockwise.

  2. If the PENDULUM needs either LEFT or RIGHT adjustment to center it in the middle of the TRIANGULAR CONTACT, then SLIGHTLY lossen the lower end of Earthquake Detectorby pulling on the bottom to separate the Velcro and move it SLOWLY left or right as reguired to center the PENDULUM. Then press the Velcro strip back together by pushing the case against the wall.

NOTE: The previous steps #5 and #6 can be repeated until you feel confident that proper alignment has been completed. Once you are satisfied that the PENDULUM is centered in the

-3-

middle of the TRIANGULAR CONTACT, connect a fresh 9-volt alkaline battery to the battery clip and place the battery into the battery compartment. The battery compartment is located on the top of the Earthquake Detector housing (see Figure 2)and is opened by lightly pushing down on the back of the cover and sliding the cover towards you (away from the wall). Reinstall by sliding in the place and pushing down on the back of the cover.

BATTERY LIFE: Replace battery every two to three years depending on the shelf life of the particular battery that you install in the sensor. Test sensor at least monthly for loud sound output.

WARNING! Prolonged exposure to loud high freguency noise can cause hearing loss.When adjusting and testing your Earthquake Detector, it is best to cover the sound ports on the front of the Earthquake Detector with masking tape or hold your fingers lightly over the sound ports.(Remove tape after adjusted.)


-4-


SENSITIVITY ADJUSTMENT

NOW is a good time to review your earthquake preparedness procedures. General information can be found in the emergency section of your phone book or by contacting your local chapter of the American Red Cross.