RFID HAT RFID Reader & Relay Buzzer Switch LED function Board
 RFID Kit03  for Raspberry Pi  model  A+ / B+ / 2B / 3B
 
MF RC522 is applied to the highly integrated read and write
13.56MHz contactless communication card chip
Low-voltage, low-cost, small size of the non-contact card chip to read and write
Smart meters and portable handheld devices developed better choice
The MF RC522 use of advanced modulation and demodulation concept completely integrated 
in all types of 13.56MHz passive contactless communication methods and protocols
14443A compatible transponder signals
The digital part of to handle the ISO14443A frames and error detection.
support rapid CRYPTO1 encryption algorithm, terminology validation MIFARE products
MFRC522 support MIFARE series of high-speed non-contact communication, two-way data
 transmission rate up to 424kbit/s

Specification:
Operating Current :13-26mA/DC 3.3V
Idle Current :10-13mA/DC 3.3V
Sleep Current: <80uA
Peak Current: <30mA
Operating Frequency: 13.56MHz
Supported card types: mifare1 S50、mifare1 S70、mifare UltraLight、mifare Pro、mifare Desfire
Environmental Operating Temperature: -20-80 degrees Celsius
Environmental Storage Temperature: -40-85 degrees Celsius
Relative humidity: relative humidity 5% -95%
Data transfer rate: maximum 10Mbit/s
Size: RFID-RC522 Module:3.9 x 6 cm The Standard S50 Blank Card :8.5 x 5.4 cm
Diameter of S50 special-shaped card: 3.1(max)

 

 

provide GUI interface control software, easy to control Relay, 18B20, stepper Motor
 

1. "Read RFID" read card information to Program              2. "Save" save card information to file

3. "Load" load card information from file                4. "on" turn on/off  switch to trigger

5. "off" turn on/off  PIR sensor to trigger      6. "on" turn on/off  18B20 sensor to trigger

6a.  18b20 temperature trigger ( Above will trigger the relay / stepper )        7. "Trigger" enable trigger for Relay & Stepper Motor

8.  Relay  "On"/"Off"   9. Relay delay time ? sec 

10. Relay repeat   11. Relay Pause after repeating on/off

12.  Stepper Motor  "Off"/"On"   13. Stepper Motor Clock wise/counter clockwise   

14. Stepper Motor speed ms/step    15. "Turns"  how many steps you want stepper motor turn

16. card information screen      17. System message screen

18. RFID control panel softwate icon



Full Support by our Pi_Scratch software can be very easy control by Scratch

Pi_Scratch detail    Scratch driver software  

 

1)Command "RFID"+"INIT" 
will initial SPI signal to active RFID Reader
2) you will see "LastRFID" & "RFID" in Sensors

Scratch demo read RFID and GPIO output


scratch demo code ( read card and compare with database)


ADD RFID Card into data base

Press “space” key then scan your RFID card

 

Active with Step Motor and GPIO Switch input


scratch demo file  

RFID_Door.sb   RFID_Reader.sb    GPIO-Card-RFID-Door.sb  

    


Package Content

1x Rs-Pi  RFID Reader

5x S50 Fudan  Card

1x Key Chains

1x  RFID kit03  function Board

1x manual 



Raspberry Pi® is a trademark of the Raspberry Pi Foundation

Payment
1.We accept payment through Paypal ONLY.

2. We ship your orders within 1-2 business days after the payment cleared.

3. We ship to address provided by PAYPAL only.

4. Our standard shipping method is from United Kingdom by Royal Mail First Class Record & Royal Mail International Sign For.

5. Usually Delivery Time approximately 1 - 2 business days, In rare cases,it may take longer due to delay in holidays.

6. If your item does not arrive within 7 days please get in contact with us. 

7. Our working day from Monday to Friday, 10am to 4pm