12 Feet of 9" wide Dupont FlexwrapNF for windows and doors, sill plate, weatherproofing, insulation. Recommended for deeper 2" X 6" construction. 12 feet is enough for three 36 inch wide doors or windows, following their installation recommendations. No need to purchase entire rolls when you only need a few feet. Average cost per foot is $2.49.
We have listings for the DuPont 4", 6" and 9" wide Flashing Tape and the 6" and 9" wide Flexwrap NF in a number of different lengths as well as full rolls. If you have a project and need a specific amount of either or both of the Flashing Tape and Flexwrap NF, contact us and we will work with you to get you what you need. We will combine all your items into one package. Click on our DuPont Flashing store category on the left to see all of our listings for these products. Tyvek Homewrap also available. Free USA shipping on this item.
Shipping this product from Alabama to the USA and Canada only. Contact us if you have any questions about the product or installation. Thank you for looking!!
DuPont recommends installing the FlexwrapNF across the sill extending 4 to 6 inches up each side. They recommend the Flashing Tape, on each side, extend 1 inch above the window and to the bottom of the sill flashing. That is about 2 inches below the window. The tape across the top should then extend at least 1 inch beyond each outer edge of the side flashing.
DuPont FlexWrap NF is a premium performance, extendable self-adhered flashing material that can be applied over a wide range of building substrates, including non-nailable sheathing materials like PSfoam board, fiberboard, concrete masonry unit (CMU), and other such materials. DuPont FlexWrap NF does not require the use of mechanical fasteners in the flexed corner areas when installed according to the flashing installation guidelines issued by DuPont.
Self Adhered Flashing Helps Seal the Building Envelope.
Self adhered butyl flashing helps prevent water intrusion at window and door sills without mechanical fasteners. Dupont recommends applying pressure after installation using a J Roller or similar tool.
DuPont™ FlexWrap™ NF self adhered flashing does not require mechanical fasteners, even in flexed corner areas around building openings. This allows it to provide easy, one-step insulation for hard-to-seal corners around windows and doors.
FlexWrap™ NF is designed to help protect vulnerable corners against air and water intrusion, as part of a complete DuPont Building Envelope Solution. It’s effective across a range of window and door designs and a wide range of typical wall substrates, including OSB, plywood, gypsum, concrete masonry unit (CMU) and other non-nailable sheathing materials.
How it Works
FlexWrap™ NF integrates easily with all DuPont air and water barriers, to help seal the building envelope for improved durability and energy efficiency.
Correctly installed, FlexWrap™ NF can help stop water from getting at the corners of windows and doors. In turn, that can help prevent water damage, such as wood rot and corrosion,as well as mold. Keeping air and water out can also help maintain insulation R-value, for improved energy efficiency.
OneStep Installation
The “NF” in DuPont™ FlexWrap™ NF means “no fasteners.” Instead, DuPont™ FlexWrap™ NF is a self adhered, extendable flashing backed with a 100% butyl-based adhesive layer, making one-step installation – and protection – possible. And because it’s an extendible flashing material, DuPont™ FlexWrap™ NF can be stretched and wrapped into a rough window opening before the window is installed, or flashed around arched or custom-shaped windows, as well as other wall penetrations.
So FlexWrap™ NF isn’t just an effective flashing to seal out water, it’s also a cost- and time-effective material for crews to work with on the job site.
Dupont and FlexwrapNF are trademarks of Dupont or it's affiliates.