DSLRKIT MID8P2U-E250 Passive PoE Injector Switch
Support EXTEND mode, max Network Cable length to 250 meters
10 Ports (2 Uplink, 8 PoE) 10/100Mbps
Midspan Mode-B Unsolicited Power(4,5+/7,8-)
Wall Mount
NOTE. When EXTEND mode enable, the Max bandwidth for the Power Link (PoE) port 1-8network port will be reduced to 10Mbps for each one. Please check your IP CAMERA's bit stream setting. We recommend the value does not over 8Mbps(8192Kbps).
(The up-link is not affected, it will always working at 100Mbps max speed)
Notice!
If you switch to the EXTEND mode, the Max allowable Network Cable length will increased to 250 meters. Then suggested buy 52V power adapter. This will avoids the power loss over the long distances, and will make sure the PoE IP Camera working.
the Max electric current of this poe switch can not be over 4A.
52V Power adapter links:
52V1.85A http://www.ebay.com.au/itm/222450192869
52V2.7A http://www.ebay.com.au/itm/222450189025
48V Power adapter links:
48V2A http://www.ebay.com/itm/191880113415
48V3A http://www.ebay.com/itm/201384084416
(Please select according your device power consumption, in order to ensure device stable running, the total power consumption should not exceed 80% of the power supply)
This item do not include the power adapter, you need to buy an extra power adapter according to your requirement. So it only suitable for PoE professional customers.
If your device support IEEE802.3af or IEEE802.3at standard，then you should select 44 -57V power adapter (typical value is 48V-52V) for them, instead of 12V.
If your camera is with word “12V/PoE” as this picture shows, then please select 48V(or 52V) Power Adapter, do not select 12V Power Adapter.
Because "12V/PoE" means it can offer power supply to camera via 12V DC port or 48V(or 52V) PoE Ethernet port:
This is an Passive Power Over Ethernet of 10 port 10 / 100Mbps-T Ethernet switches, including 8 unsolicited PoE Ethernet ports and 2 Uplink ports. DC port apply 12~55V power supply adapter(not included), any one of the 8 port can provide output power, each Ethernet port can provide network transmission speeds of up to 10 / 100Mbps , with Cat5 / 5e / 6 network cable.
This POE switch only support 10/100M connection, PoE ports do not support Gigabit ethernet connection, because "Power Link 1~8" port using 4,5,7,8 pin as power transfer, Please do not connect any "NONE PoE gigabit ethernet device and Uplink device" on "Power Link 1~8" port, this will damage your device.
Gigabit(10/100/1000Mbps) ethernet device Please do not access "Power Link port" this will damage your device
Features:
- 10 x 10/100Mbps Auto-negotiation Fast Ethernet RJ-45 ports with 8-Ports PoE function
- Support EXTEND mode, max Network Cable length to 250 meters.
- Midspan Mode-B Unsolicited Power(4,5+/7,8-)
- Supports 12~55V DC power supply
- Each port supports auto MDI/MDIX, so there is no need to use cross-over cables.
- Full/half duplex transfer mode for each port.
Specification:
| ALL Port: | Standard 10/100Mbps Ethernet port. Support 10Mbps Ethernet and 100Mbps Fast Ethernet, can operate in full-duplex or half-duplex mode,must work with 4 pairs UTP Cat5/5e/6 cable。 | |||||
| Power Link Port 1-8: | any supported unsolicited power on pairs 45-78 pins compliant Powered Devices (PDs) | |||||
| Power LED | LED ON: power on. LED OUT: power off | |||||
| Green Light LINK/ACT | LED ON Indicates the port is connected to a network device and has been started | |||||
| LED OFF Indicates that this port is not connected to a network device or has not been started | ||||||
|
Standard |
IEEE 802.3 10BASE-T Ethernet |
|
IEEE 802.3u 100BASE-TX Fast Ethernet |
|
|
IEEE 802.3x Full-Duplex flow control |
|
|
Protocol |
CSMA/CD Ethernet |
|
Data Transfer Rate |
Ethernet: 10Mbps (Half Duplex) 20Mbps (Full Duplex) |
|
Fast Ethernet: 100Mbps (Half Duplex) 200Mbps (Full Duplex) |
|
|
IC Chips |
IC Plus IP178G + IP175G |
|
Network Media(Cable) |
10Base-T(EXTEND mode): UTP category 5e, 6 cable (maximum 250m) EIA/TIA-568 100Ω STP (maximum 250m) |
|
100Base-TX:UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100Ω STP (maximum 100m) |
|
|
PoE Power on RJ45 |
Power +: pin 4 & pin 5 ; Power -: pin 7 & pin 8 |
|
DC Output: 9-55V, Per port Max 1A, |
|
|
Number of Ports |
10 x 10/100Mbps Auto-Negotiation RJ45 ports with 8 PoE enabled (port-1 ~ port-8) |
|
Power Input |
Supports INPUT 9-55V DC power supply |
|
Power DC port 5.5 x 2.1mm, (Maximum current 4 amps) inside positive (+) outside negative (-) |
|
|
Power Consumption |
3.2 Watts (max. no PD connected) |
|
According to the actual power consumption of equipment |
|
|
Temperature |
Operation Temperature:0 ~40℃ (32 ~104℉) |
|
Storage Temperature: -40 ~70℃(-40 ~158℉) |
|
|
Humidity |
Storage Humidity 5%~90% non-condensing, Operating Humidity 10%~90% non-condensing |
|
Product Dimensions |
197mm W x 73mm D x 32mm H |
|
RAM Register Capacity |
64K bytes per device |
|
MAC Address List |
1K entries per device |
|
Frame Forward Rate |
10Mbps Ethernet: 14880pps/Port 100Mbps Ethernet: 14880pps/Port |
Item Included:
DSLRKIT MID8P2U-E250 10ports 8PoE Unsolicited(Passive) PoE switch x1
(Power supply not included)
12 Months Warranty from the date of purchase.
