Standard Print Co. eBay Store        
Standard Print Co. Logo
   
   
ABS I PLA I PLA+ I HIPS I PETG I Flexible
 Standard Print Co Filament

HIPS Filament 1.75mm

     


A durable and impact resistant 3D printing material, our HIPS a great 3D printing material for light, durable and impact resistant parts. Better still, HIPS is dissolvable in d-limonene making it an excellent choice as a dissolvable support material, leaving your parts free of any markings caused by support removal. Sharing many of the same printing properties as ABS, HIPS makes for a great dual extrusion partner when paired with ABS.

     
 
 

 

   

 

      

Available Colours

 
    Available Colours
   

 

   
        
±0.03mm Tolerance Anti-Kink Technology Transparent Spools No Bubbling
 

±0.03mm
Tolerance

Anti-kink Technology

Transparent
Spools

Bubble
Free
          

 

Printing Parameters*


  
Filament Type: HIPS Print Speed: 30 - 80 mm/s
Printer Type: Cartesian/Delta Printing Temperature: 220 - 240°C
Extruder Type: Direct Drive/Bowden Build Bed Temperature: 50 - 80°C
Layer Height: 0.1 - 0.3mm Retraction Speed: 20 - 50 mm/s
Fill Density: 0 - 100% Retraction Distance: 3 - 10 mm
Shell Thickness: >0.4mm Cooling Fan: Yes

*Not all 3D printers are the same as such, printing settings may vary from printer to printer. Actual printing parameters may differ from those suggested above. Do not be afraid to adjust your printers settings 


          

Hardware Requirements


Hardware Requirements Heated Bed Heated Bed:
Yes

Enclosure: 
Yes

 Hardened Nozzles:
Not Required  		 Hardware Requirements Heated Bed

Adhesion Aids:
Not Required

 

Hardware Requirements Heated Bed Part Cooling Fan: 
Yes




     
   
        

Spooling Options

        
  •  ECO Spool - Standard Print Co.

    ECO Spool 1kg 

    Part of our campaign to reduce the use of single use plastic. Our environmentally friendly ECO spools are fully reusable and are designed to be refilled with any material refill across our entire product range. This saves on raw materials, improves shipping efficiency, decreases the price for you and means less single use waste is produced.
     
    • 100% Recyclable Spools
    • Designed to be reloaded when empty with 1kg refill spools.
    • Compatible with all materials in refill 1kg spool range
    • Clear sides for quick gauging of remaining filament 
    • Spool Diameter: 20cm - Width: 6.6cm - Hole Diameter: 5.3cm
    • Package Contains: 1 x ECO Spool with 1kg pre-loaded filament
  •  Refill Spool 1kg - Standard Print Co.

    Refill 1kg - No Spool 

    Why pay for something you're just going to throw out? Our Refill 1kg is produced as a spool-less filament refill in an Australian first. By offering all filaments in a refill format, we’re able to offer a slimmed-down product, 25% lighter than a traditional spool while still packing the same amount of filament. This saves on raw materials, improves shipping efficiency, decreases the price for the consumer and means less waste at end of life.
     
    • Save up to 20% per kg - Cheaper Filament
    • Reduces plastic waste - No piles of empty spools destined for landfill
    • Reload filament onto ECO Spools in seconds.
    • Compatible with all Standard Print Co. ECO Spools
    • Refill Diameter: 17.5cm - Width: 5.8cm - Hole Diameter: 8cm
    • Package includes: 1 x 1kg roll of filament without a spool
             


 

       

How to Respool an ECO Spool with a  Refill
How to respool a standard Print Co. Eco Spool and Refill

 


Step 1: To re-spool an empty Standard Print Co. ECO spool, first loosen the four securing screws  on the reverse face of the spool with a 3mm Allen key.

Step 2: After removing the backing plate, slide your PLA refill onto the spool.

DO NOT cut the filament coil's securing straps at this stage. Doing so will result in the filament uncoiling completely, making it next to impossible to recoil in an orderly manner.

Step 3: Secure the end of the filament located on the inner diameter of the refill filament coil in the groove located on the inner diameter of the ECO spool before replacing the backing plate of the inner spool. Failure to do this will cause the refill filament coil to spin independently of the ECO spool.

Step 4: Resecure the four screws holding backing plate to the ECO spool.

Step 5: Only after the filament has been secured and backing plate replaced, should a pair of scissors be used to carefully cut and remove the four plastic straps holding the filament coil together being careful not to cut or damage the filament itself. 


        
             

The Standard Print Co. Difference                                         

        
       
  •    
    •    
  •    
    •    
  •    
    •  
 
                     
 
     
                     
 

 

                    
   
            

 

About Us 

At Standard Print Co. we believe that only with the right tools can one realise their creative potential. We're proud to offer Australia the world's most accurate and affordable 3D printing supplies. (Because why should the best filament in the world cost more?)

Shipping 

All orders are dispatched via courier delivery. Every order will be insured for up to $300 and tracked for free. Thats right, FREE! Please allow 2-5 days for your order to be delivered. Orders placed before 1pm GMT+10 will be dispatched on the same business day. 

Payment

We accept payment through PayPal only, however you do not need a PayPal account to pay for your goods. PayPal will accept Credit and Debit card payments. The following cards and accounts are accepted: Visa, Mastercard, Paypal.

Returns

For peace of mind, if you are in anyway unsatisfied with your purchase or have simply changed your mind, Standard Print Co. offers no questions asked full refunds on your purchase. (less postage and handling) for products that are&unopened and still in its original packaging. If you'd like to return your purchase, simply mail it back to us. 

   
 
   
       

Standard Print Co. | Sydney | Australia | 2021