You may also like
Related instructions
Three operating modes. Wired, WiFi ,3G/4G.
In the place where the camera is installed, there is no network or WIFI signal. But have SIM mobile signals.
You can install a SIM card to the camera and connect the Internet by your SIM card
Tips: When using 3G/4G. Do not connect the network cable at the same time . Avoid IP assignment conflicts.
How to quickly set up 3G/4G
First of all , Download APP "CamHi" from the iPhone App Store or Google Play Store. Or scan the QR code
If you choose the camera has 3G/4G. Then when the camera leaves the factory. The default connection to the 3G/4G module (signal MIFI-XX) has been set.
You only need a few simple steps.
Insert the SIM card into the camera. Connect the power adapter , wait 10-20s, camera will be ready.
Then open your phone WLAN setting , you will find "MIFI-XXX" and select to connect, the default password is 1234567890
When your phone is connected to MIFI-XX. Then open the app "camhi". Select "Add Camera."
Because your phone is connected to MIFI-XX. So you can choose "Search Camera from LAN". Or directly scan the QR code of the camera.
Then you can see your camera online. You can control the camera and watch videos from your phone.
②Frequency not supported or SIM card arrears when prompted "No Service" or "Limited Service", as shown below 1):
③Make sure 3G/4G signal strength is enough, as shown below 2):
| Package Includes |
|
| Basic Parameters Table | ||||
| Camera | ||||
| Signal System: | PAL(50HZ) / NTSC(60HZ) automatic identification | |||
| Infrared: | 4pcs big Array IR Leds 32 mil , Infrared distance about 50M | |||
| Day& Night: | Dual IR-cut filter auto switch | |||
| Sensor Size: | Low Illumination 1/3" SONY 323 CMOS 1080P+HI3516E | |||
| Wireless Protocols: | 802.11b/g ,150Mbps. 15-50m | |||
| 4G: | 4G standard:FDD-LTE | |||
| Frequency range: B1(2100MHz), B3(1800MHz), B7(2600MHz), B8(900MHz), B20(800MHz) | ||||
| Transmission rate :Upload max:50Mbps, download max: 150Mbps | ||||
| Security:WEP, WPA/WPA2, WPA-PSK/WPA2-PSK | ||||
| 3G: | 3G standard:WCDMA | |||
| Frequency range:B1(2100MHz), B8(900MHz) | ||||
| Transmission rate:Upload max:5.76Mbps, download max: 21Mbps | ||||
| PTZ: | Rotation angle:Horizon: 0 to 300°. Vertical: 0 to 60° | |||
| Horizontal speed:12°/S | ||||
| Lens: | 4.7-47mm 10× auto zoom lens | |||
| Video | ||||
| Video Codec: | H.264 main profile and baseline | |||
| Video Resolution: | 5MP | |||
| First stream: | 1920x1080/1280x720 | |||
| Second stream: | 640x352 | |||
| Third stream: | 320x176 | |||
| JPEG code rate: | (640x352), (320x176) can be set (for mobile monitoring) | |||
| Frame Rate: | 1-20fps(PAL), 1-20fps(NTSC) | |||
| Video Compression: | 32Kbps~8192bps | |||
| Image Settings: | Brightness,Saturation,Contrast,Sharpness,Exposure,Gamma,Distortion,Flip , Mirror, WDR | |||
| OSD Settings: | Time Stamp,Time show,Camera name,Name show | |||
| Privacy Mask: | 4 Configurable regions | |||
| Network | ||||
| Network Protocol: | TCP/IP, HTTP, TCP, ICMP, UDP, ARP, IGMP, SMTP, FTP, DHCP, DNS, DDNS, NTP, UPNP, RTSP, ect. | |||
| Access Protocol: | i13, P2 | |||
| Function Support | Support P2P | |||
| Support motion detection alarm (4 areas can be adjusted, the sensitivity can be adjusted) | ||||
| Support alarm picture to send E-Mail | ||||
| Support Alarm picture or video upload FTP server | ||||
| Support timed capture pictures to FTP server | ||||
| Support Micro SD card function, maximum support 128G Micro SD card | ||||
| Support for static IP, also supports dynamic IP (DHCP) | ||||
| Support IE, Google, Firefox browser,Recommend to use IE browser. | ||||
| Up to 12 users can browse simultaneously(each stream supports 4 users) | ||||
| Interface | ||||
| Network: | 1 * RJ45 10Base-T/100Base-TX ethernet interface | |||
| Power: | 1 * Ø5.5 RCA interface | |||
| Audio (Optional): | Audio Codec: G.726/G.711 | |||
| Audio input : Built-in microphone | ||||
| Audio output : 1 RCA output, support for connecting headphones or amplifier ( tail line support) | ||||
| General | ||||
| Anti-thunder Level: | Standard IEC61000-4-5 | |||
| Operating Conditions: | -20 °C ~ 55 °C Humidity 95% or less (non-condensing) | |||
| Power Supply: | DC12V 1-2A | |||
| Power Consumption: | 3W(daytime), 9W(night) | |||
| Housing Material: | Metal | |||
| Applicable: | Indoor use / Outdoor use(Waterproof IP66) | |||
| Weight: | 1.15kg | |||
