Description:

Application occasions:

1. DIY full compatible/full protocol mobile phone flash charging module for electronics enthusiasts, mobile phone repairers, and electronics industry personnel!

2. In outdoor occasions, long-term power outages, etc., use DC power supplies such as batteries, solar panels, etc. to flash charge mobile phones of various brands!

Feature of product

Strong compatibility:

USBPD3.0 (PPS) support

Qualcomm QC4+/QC4.0/QC3.0 support

Huawei SCP/FCP support

OPPOVOOC support 

Apple2.4A support

Samsung AFC support

OnePlus DASH support 

VIVO9V2A dual-engine flash charging support

MediaTek PE2.0 support

Reminder: Some similar fast charging boards on the market use the IP6518 solution, which does not support QC4.0, VOOC, DASH, and is not serious.

Fast charge agreement. And the output current of IP6518 is limited, so the compatibility with Huawei Super Fast Charge SCP is not good.

High efficiency, full power:

1. Using external MOS tube, the conversion loss is much lower than the built-in MOS of the IP6518 solution;

2. It adopts two-wire parallel winding + iron-silicon-aluminum magnetic ring, which has higher efficiency and lower heat generation than chip inductors at the same power! ! !

3. Both input and output are dual parallel low-resistance electrolytic capacitors, with 6 1206 SMD ceramic capacitors! Only for higher performance!

Measured picture: Perfect realization of Huawei's super fast charging 5V4.5A (SCP)

Additional configuration:

1. Flexible power supply mode

Standard configuration of red and black power cables, optional 5.5 female head cable/crocodile clip power supply!

2. Wide supply voltage: 6 to 35V! (IP6518 scheme is 10.5~32V) 

3. High-performance input anti-reverse connection

A dedicated MOS tube is used for anti-reverse connection. Although the cost is high, the effect is far better than that of diodes, and it is not hot (the heat generation is close to zero!)

4. Equipped with fast charging status indicator

The blue light is the output indicator, and the red light is the fast charging status indicator!

5. Dual independent current limiting

6. Ultra-thin design, optional shell!

Fast charging board size: 50*17*12mm

Precautions:

1. If the fast charging board is equipped with a shell, the default power supply is 5.5mm plug! If you need red and black power cords to supply power, please contact customer service!

2. The shell is refitted by hand! Be cautious for users who pursue perfect details! 

3. TYPE_C port is used for output charging! Cooperate with C-TO-C/TYPE_C male-to-male dual-head data cable to charge mobile phones or laptops!

4. OPPO and OnePlus phones need to use USB to charge!

Protocols such as QC4+/QC4.0/PD3.0 must use TYPE_C port! 

5. When the power supply voltage is higher than 21 volts, the C-port PD protocol supports up to 20V3A output, and the module is small. Please charge the notebook

Good ventilation and heat dissipation! 

6. When the USB port and TYPE_C port are plugged into the phone at the same time, both ports are 5V output! 

7. Professional car chargers/high-efficiency DCDCs rarely use chip inductors, and they basically use sendust magnetic rings! ! Because the chip inductance

Low cost, but big heat!

Multi-brand mobile phone charging test:

USB port:

1. Charge Huawei Mate20 (56% battery): turn on SCP fast charge mode

Voltage 4.89V, current 4.59A

2. Charging Huawei P20Pro (12% battery): Turn on SCP fast charging mode

Voltage 5.03V, current 4.25A 

3. Charge Honor V20 (43% battery): Turn on SCP fast charge mode

Voltage 5.13V, current 4.5A

4. Charge Xiaomi Mi 8 (18% power): turn on QC3.0 fast charge mode

Voltage 6.44V, current 2.79A 

5. Charge OPPOR17 (43% power): turn on VOOC flash charge mode 

Voltage 4.8V, current 3.8A 

6. Charge iPhoneXS (5% battery): turn on APPLE2.4A mode 

Voltage 5.22V, current 2.37A 

7. Charge OnePlus 6T (15% power): Turn on DASH flash charging mode 

Voltage 4.7V, current 3.8A