1.2A 10-100V High-Power LED Constant Current Drive Module High Voltage Converter
Features
High voltage and high power, suitable for LED lighting, headlight conversion, LED spotlight, cross-current load
small size, high power, automotive safety chip, built-in multiple intelligent protection functions.
Overheat protection, undervoltage protection, easy to install.
High voltage resistance, wide voltage input, high power output, practical and durable
Wide range of use, can be widely used in headlight conversion, solar lighting, low-voltage AC power generation lighting, and other cross-current drive applications.
High voltage and high power, suitable for LED lighting, headlight conversion, LED spotlight, cross-current load
small size, high power, automotive safety chip, built-in multiple intelligent protection functions.
Overheat protection, undervoltage protection, easy to install.
High voltage resistance, wide voltage input, high power output, practical and durable
Wide range of use, can be widely used in headlight conversion, solar lighting, low-voltage AC power generation lighting, and other cross-current drive applications.
Specification
PCB material: aluminum base board
Input range: wide voltage 10V-100V
Support: up to 65V AC input
Output current: up to 1.2A
Support: Output high and low bright mode
Standby current:as low as 0.3mA
High efficiency: up to 96% or more
Built-in intelligent temperature protection, high temperature drop current
Product size: length, width and height: 40*20*9.35mm
4 screw hole size: diameter 2.8mm
PCB material: aluminum base board
Input range: wide voltage 10V-100V
Support: up to 65V AC input
Output current: up to 1.2A
Support: Output high and low bright mode
Standby current:as low as 0.3mA
High efficiency: up to 96% or more
Built-in intelligent temperature protection, high temperature drop current
Product size: length, width and height: 40*20*9.35mm
4 screw hole size: diameter 2.8mm
Use method
1: Determine the LED power supply for constant current, the general LED lamp preamp did not add power supply circuit board
2: determine the load LED needs current, set the current in advance
* drive current is equal to the above chart marked resistor 1 setting value plus resistor 2 setting value
* drive current calculation formula is: current = 0.1/resistance value (board default resistance 1 and 2 are 0.25Ω, ISET is not shorted, the current is about 0.4A, ISET shorted, the current is approximately equal to 0.4A + 0.4A). Note that the calculation here is only the approximate current, the actual current will be based on the actual application will have a certain error, you can produce test details after the graph.
* If the highlight switch line short to the negative side of the power supply output current will be set to double the current, the use of this function requires a power supply greater than 11.5V, if the input AC power can not use this method.
3: Install the module, connect the power supply and LED lights in accordance with the wiring diagram
1: Determine the LED power supply for constant current, the general LED lamp preamp did not add power supply circuit board
2: determine the load LED needs current, set the current in advance
* drive current is equal to the above chart marked resistor 1 setting value plus resistor 2 setting value
* drive current calculation formula is: current = 0.1/resistance value (board default resistance 1 and 2 are 0.25Ω, ISET is not shorted, the current is about 0.4A, ISET shorted, the current is approximately equal to 0.4A + 0.4A). Note that the calculation here is only the approximate current, the actual current will be based on the actual application will have a certain error, you can produce test details after the graph.
* If the highlight switch line short to the negative side of the power supply output current will be set to double the current, the use of this function requires a power supply greater than 11.5V, if the input AC power can not use this method.
3: Install the module, connect the power supply and LED lights in accordance with the wiring diagram
Module List
1 x Module
1 x Module
Module + Cable List
1 x Module
2 x Cable
1 x Module
2 x Cable
- All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
- We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
- We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
- Payment must be received in 5 business days of auction closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Il 3-mar-2023 alle 09:32:16 CET, il venditore ha aggiunto le seguenti informazioni sulloggetto: