Infrared Reversing Radar Part Electronic Range Sensing Reminder Sensor
Features
1. Use high quality materials, quality assurance
2. The infrared reversing radar is composed of multi-harmonic oscillation circuit, infrared signal transmitting and receiving circuit, infrared signal amplifying and voltage comparison circuit, which has the characteristics of simple circuit, low cost and stable circuit work.
3. Time base circuit NE555 and surrounding components form a multi-harmonic oscillator to generate infrared wave signal, which is output by IC2 pin 3 and drive infrared transmitter tube HFS to transmit infrared signal.
4. Exquisite and compact appearance
5. Widely used in a variety of distance measurement occasions
2. The infrared reversing radar is composed of multi-harmonic oscillation circuit, infrared signal transmitting and receiving circuit, infrared signal amplifying and voltage comparison circuit, which has the characteristics of simple circuit, low cost and stable circuit work.
3. Time base circuit NE555 and surrounding components form a multi-harmonic oscillator to generate infrared wave signal, which is output by IC2 pin 3 and drive infrared transmitter tube HFS to transmit infrared signal.
4. Exquisite and compact appearance
5. Widely used in a variety of distance measurement occasions
Specification
Supply voltage: DC9V (DC power supply)
Board size: 70*45mm
Supply voltage: DC9V (DC power supply)
Board size: 70*45mm
Production techniques
Soldering and component installation is the key to success, please use high quality solder, solder joints should be bright without false solder leakage, components should not be installed incorrectly, follow a certain order in the production, install part of the components and then install another part. Start with the installation of short components, such as resistors, and then install high components. Chip notch position against the board with a notch mark.
1, installation of chip resistors, resistors do not distinguish between positive and negative;
2, the installation of NE555 \ LM324, first solder a pin to fix the chip, in the other pins to the tin soldering completed. Pay attention to the installation direction of the chip, mark the point to align the mark point location installation.
3, the installation of 1N4148, black circle position aligned with the board black mark position.
4、The porcelain chip capacitor has no positive and negative polarity. Electrolytic capacitor long foot is positive, corresponding to the position of the circuit board with positive.
5, light-emitting diode and infrared transmitting and receiving diode long foot is positive, corresponding to the location of the circuit board with positive.
After installation, check again whether the components are installed wrong, whether the welding is good, and then access to 9V power supply, pay attention to the positive and negative power supply can not be connected to the reverse.
Soldering and component installation is the key to success, please use high quality solder, solder joints should be bright without false solder leakage, components should not be installed incorrectly, follow a certain order in the production, install part of the components and then install another part. Start with the installation of short components, such as resistors, and then install high components. Chip notch position against the board with a notch mark.
1, installation of chip resistors, resistors do not distinguish between positive and negative;
2, the installation of NE555 \ LM324, first solder a pin to fix the chip, in the other pins to the tin soldering completed. Pay attention to the installation direction of the chip, mark the point to align the mark point location installation.
3, the installation of 1N4148, black circle position aligned with the board black mark position.
4、The porcelain chip capacitor has no positive and negative polarity. Electrolytic capacitor long foot is positive, corresponding to the position of the circuit board with positive.
5, light-emitting diode and infrared transmitting and receiving diode long foot is positive, corresponding to the location of the circuit board with positive.
After installation, check again whether the components are installed wrong, whether the welding is good, and then access to 9V power supply, pay attention to the positive and negative power supply can not be connected to the reverse.
Circuit debugging
In the case that there is no obstruction above the infrared transmitter tube and receiver tube, adjust RP1 to make the LED3 on the circuit board light up, and then adjust RP1 in the opposite direction to make the LED3 just go out. Then use a reflective object (you can use white paper) to gradually approach the position between the infrared transmitter tube and the infrared receiver tube from a distance, and as the distance approaches, LED3 to LED1 lights up in turn, and the infrared reversing radar is pressed and installed.
In the case that there is no obstruction above the infrared transmitter tube and receiver tube, adjust RP1 to make the LED3 on the circuit board light up, and then adjust RP1 in the opposite direction to make the LED3 just go out. Then use a reflective object (you can use white paper) to gradually approach the position between the infrared transmitter tube and the infrared receiver tube from a distance, and as the distance approaches, LED3 to LED1 lights up in turn, and the infrared reversing radar is pressed and installed.
List
1 x DIY kit
1 x DIY kit
- All package need to wait 30 days(US only need 7-10 days),Please take care it.Less than 30 days,we can't take a refund.
- If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please keep in touch with us and double check the return address before you return it.
- If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.
- We maintain high standards of excellence and strive for 100% customer satisfaction! Feedback is very important to us. We request that you keep in touch with us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns.
- We accept PayPal only. But we only Accept your Ebay Address,Please Make sure it's 100% right.
- Payment must be received in 5 business days of auction closing.
- Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order.
- Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched.
Il 9-mag-2023 alle 03:14:03 CEST, il venditore ha aggiunto le seguenti informazioni sulloggetto: