ITEM DESCRIPTION

Dental Laminator Vacuum Forming Machine Oral Material Making Orthodontic Retainer Laminator Belt Steel Ball Forming Machine Soft Film Sheet Hard Film Sheet Press Mold Sheet Forming Sheet

Specification

Packing size: 23*28*34cm

Weight: 6KG

Power supply: 1000W

Comes with a copy of the original laminated steel ball

USE 

Braces forming, forming and making of bleaching braces

Appliance molding, orthodontic retainer, dental arch splint molding and fabrication

Tray forming, forming and fabrication of fluoride trays

Base forming, forming and production of temporary, permanent base and mouthguard

THE PURPOSE AND USE OF STEEL BALLS

Remove the aluminum box, place the model in the middle, then use steel balls to bury the part that does not need to be formed, and then put it on the machine table.

PRODUCT OPERATION

Rotate the upper cover (both left and right) 90°, put the required diaphragm 

between the upper and lower casings, and pull down the ball head lever to clamp it. 

Reset the upper cover, press the lifting wrench to raise the sleeve frame to the 

working height, (the upper part of the main shaft is limited by the marble), and at 

the same time place the packaged product in the center of the screen plate, turn on 

the heating switch, heat the diaphragm, when the wax When the sheet is heated 

below the lower frame plane 1CM (about two or three minutes). Turn off the heating 

switch, put the frame down, and turn on the vacuum motor at the same time. After 

the package is formed, it can be removed.

HOW THE RETAINER WORKS

The orthodontic transparent retainer has the advantages of no snap ring, beautiful appearance, comfortable wearing, stable effect, and simple production. Two tools are used first: a vacuum former and a special plastic sheet. The plastic sheet used in orthodontics is relatively hard, and 0.8MM ~ 1.5MM can be selected.

1. Take an impression.

2. Fill in plaster and wait for the plaster model to dry, then trim the model, remove the part of the palate and the base of the tongue, it is best to make it into a "U" shape.

3. Place the forming sheet on the forming machine, clamp it, lift it to the heating place, and place the finished model on the vacuum suction cup of the vacuum forming machine.

4. Use a vacuum heater to heat the hard piece, let it sag about 2 cm, the deeper the sag, the thinner the holder will be. Move it down on the model until it is fully seated.

5. Use a vacuum machine for 15-20 seconds to ensure molding, remove the heater, and remove the mold when it cools down.

6. Trim off the excess with scissors, or use a bur to grind it down 2~3MM directly below the gingival margin, trim the edge, and keep 0.5 mm below the gingival margin.

7. After the braces are trimmed, place the braces on the model again to check whether they fit. Such an orthodontic retainer is made. If you feel that the edges are not tight, you can bake it with an alcohol lamp and bend it inward until it is tight. In the same way, plastic sheets of different thickness and hardness can be used to make whitening trays, night grinding pads, etc.

Overweight Warning:

For some countries and regions, the transportation weight of this item may exceed the weight limit of the standard methods.

We will contact you as soon as we receive the order, and then help you cancel the order or pay extra freight for other modes of transportation.

Sorry for the inconvenience,please understanding,thanks.

WARNING

The following FDA Disclaimer is required for all eBay listing in Healthcare category and is included for REFERENCE:

The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. 

If so, do not bid on this item unless you are an authorized purchaser. 

If the item is subject to FDA regulation, We will verify your status as an authorized purchaser of this item before shipping of the item.

STATEMENT

Please find out as much as you can about your import taxes in your own country before bidding the item.

You need to pay for the import duties in case that occurred for certain goods, 

or you may kindly give us some suggestions about that, we promise to do our best to help you!

PAYMENT

We only accept payment online,enables you to make payment quickly and securely.

1).Before payment,please read ads carefully,about order requests and notices.

2).Please pay the money within 5 days after add to the cart,overdue,we will cancel unpaid order.

3).Please offer correct full delivery informations,and home or mobile phone number so that we can make sure you get the item safely.

1). All items will be shipped by Airmail post within indicated handling time.

2). The trade is cross-border and Airmail is the cheapest post way, so it take a long time for delivery. 

If you don't want to wait so long time, please kindly contact us for other shipping methods.

Meanwhile, we offer other choices in the shipping methods which you can choose yourself,need to pay extra difference shipping fee.

3).We are not responsible for your Customs duty or taxes. Pay attention,we are not responsible for any parcel problems caused by the customs of the destination country. 

4).VAT or other charges, fees is charged by eBay.

TERMS

We guarantee new equipment other than accessories to be free from defects in workmanship and materials for a period of three months

from the date of shipment under normal use and service.

Our company's obligation under this warranty is limited to repairing, 

at our company's option, any part which upon our company's examination proves defective.

More than three months,do not provide free replacment.

CONTACT US

During the working time ,we will reply you as soon as possible. 

If your orders or parcels have any problems, please contact us through eBay message at the first time.

We will try our best to help you to solve, thanks.