600115 4WD Front Differential Axle Actuator Disconnect Housing Fits for 2002-2009 Chevy Trailblazer Envoy Bravada Ascender 9-7X, Intermediate Shaft Bearing Assembly Replace# 12471623 600-115
- The 4WD axle actuator housing, also called axle disconnect housing, is part of differential that houses the gears and shift fork required to lock both front axles together. It works together with transfer case to send torque to all four wheels. Most of the time, the vehicle is in RWD.When 4WD is engaged, transfer case engages the front driveshaft. It’s still necessary, though, to connect two front constant velocity (CV) axle shafts. This is done via a front differential and the axle actuator.
- Due to its location underneath the vehicle, the axle actuator housing can be exposed to dirt, road salt, and other pieces of road debris. These can damage the actuator housing, which will make it less effective at protecting the moving parts inside. Then, dirt can get inside of the actuator to cause bearing wear or lubricant leakage. Wear can also simply occur over time from use. If you try to shift the vehicle into 4WD at speed, the high forces involved might crack the actuator housing.
- This 4WD AxleAactuator Housing Fits for the Following Vehicles: 2004-2007 Buick Rainier, 2002-2009 Chevro-let Chevy Trailblazer, 2002-2006 Chevy Trailblazer EXT, 2002-2009 GMC Envoy, 2002-2006 GMC Envoy XL, 2004-2005 GMC Envoy XUV, 2003-2008 Isuzu Ascender, 2002-2004 Oldsmobile Bravada.
- Customers can find the product you need accurately according to the OE number. part number: 12471623, 12471625,12471627,12471628,12471629,12471633,12471636,12479081,12479197,12479302,15801507, 26036092, 26053326, 600-115.
- Our Four-Wheel Drive (4WD) Actuator Housing is quality-engineered to restore the four-wheel drive to proper operation. It includes all the hardware necessary for a complete repair. It helps shift four or all wheel drives to rear wheel drive and helps shift four or all wheel drives to rear wheel drive. Direct for a proper fit every time.
Product Description
What is it?
The 4WD axle actuator housing, also called axle disconnect housing, is part of differential that houses the gears and shift fork required to lock both front axles together. It works together with transfer case to send torque to all four wheels. Most of the time, the vehicle is in RWD.When 4WD is engaged, transfer case engages the front driveshaft. It’s still necessary, though, to connect two front constant velocity (CV) axle shafts. This is done via a front differential and the axle actuator.
Customers can find the product you need accurately according to the OE part number. This is a compatible part manufactured our factory. Associated vehicle models and part numbers are used in this listing only to identify the vehicles this 4WD axle actuator housing fits.
Part Number:
- 12471623, 12471625, 12471627
- 12471628, 12471629, 12471633
- 12471636, 12479081, 12479197
- 12479302, 15801507, 26036092
- 26053326, 600-115, 600115
For exact years and models, please check compatibility.
Compatible with:
2004-2007 Buick Rainier
2002-2009 Chevro-let Trailblazer
2002-2006 Chevro-let Trailblazer EXT
2002-2009 GMC Envoy
2002-2006 GMC Envoy XL
2004-2005 GMC Envoy XUV
2003-2008 Isuzu Ascender
2002-2004 Oldsmobile Bravada
How to replace the 4WD axle actuator housing?
1. Raise & support the vehicle properly, remove the passenger front wheel, splash shield, & then remove the passenger front CV axle.
2.remove the electric axle actuator from the axle disconnect assembly by removing the 2 bolts and electrical connector. The axle actuator has gone through just as many cycles as the disconnect and if the disconnect failed, well then the axle actuator is probably right behind it.
3. Remove the wire harness clip located on the axle disconnect and the old disconnect assembly
4. Remove the new part from the box and remove the protective plastic plugs inside of each seal.
5. The new units are pre-greased internally from the factory, however just like most any seal, it is a good idea to apply a small amount of lube along the lip of each seal with your finger. This prevents the seals form being damaged when the metals shafts slide through them during installation.
6. Install the new unit and make sure it is flush to the oil pan.
Item Specification
-
Item model number 600-115 OEM Part Number 12471623，600-115，12471625，12471627，12471628，12471629，12471636，12479081，12479197，12479302，15801507，26036092，26053326，600-115 Manufacturer Part Number 12471623 Item Weight 6.29 pounds Model 600-115 Package Dimensions 9.5 x 6.5 x 6.5 inches
- Product Dimensions: 6.5 inches x 9.5 inches x 6.5 inches. Weight: 6.29 lb
- Fast shipping is very important for us.
Our standard shipping service is FREE.
Your order will be shipped within 1-3 business days upon full payment received.
Most items are delivered within 3-5 business days, however, please allow 3-10 business days.
We are shipping only to USA.
We only ship to the confirmed Paypal address. We reserve the right to cancel any order for any reason at any time.
We are not responsible for undeliverable addresses.
- We offer a 30 day return policy from checkout winning date.
Your satisfaction is guaranteed! If for any reason you are unhappy with your item, just return it within 30 days for a full refund, minus shipping cost. Please contact us prior to initiating a return so that we can issue you a refund authorization.
Items defective upon receipt must be packaged in their retail packaging as if new and returned with a detailed description of the problem.
Return shipping fees are not refundable.
We reserve the right to decline any returns if the above guidelines are not followed.
- All of our items, unless otherwise stated, will only run on 120 volts. Please check to make sure your country complies with these specifications.
If you have a problem or question regarding your transaction please contact us before leaving any type of feedback. We will work with you to resolve any problem you may have.