Vendo questa scheda PCB che realizza da I2S a uscita analogica stereo differenziale.

La scheda prevede l'utilizzo di due moduli DAC R2R che ho in un'altra inserzione:


https://www.ebay.it/itm/326068975578


Inoltre la scheda è priva di tutti i componenti discreti così da poter permettere una personalizzazione sul progetto.

Una manciata di porte TTL per far funzionare quattro DAC che lavorano a coppie in parallelo.

I due canali Sx e Dx sono perfettamente sincronizzati come anche le uscite + e - del segnale analogico. Può essere utilizzato anche con singola uscita utilizzando solo GND e segnale + con il vantaggio di un miglior rapporto segnale rumore rispetto la versione non duale.

Potete vedere il segnale triangolare in uscita.

La sezione di uscita è realizzata con un circuito a valvole. Fondamentalmente è un sommatore differenziale. Nella sezione di ingresso l'accoppiamento è DC. Nella sezione di uscita è previsto un condensatore. Non essendo necessario un guadagno elevato è sufficiente pilotare le valvole con tensioni non elevate. Il circuito è stato collaudato con 60 V di anodica utilizzando due tubi 12AU7 (ECC82) ma può essere personalizzato come meglio si preferisce.

L'interfaccia è totalmente in hardware logico.

Lavora in modalità non oversampling e accetta frequenze di clock oltre il classico 44.1 Khz in foto la vedete funzionare a 384 Khz di sample rate, utilissimo per i file DSD.

Alimentazione 5V DC per il digitale, 12V DC per i filamenti (Heater) e 60 V per anodica (High Voltage).

In foto vedete la PCB completa in funzione.

Ottima per costruire il convertitore definitivo senza integrati DAC, suono puro diretto.



ATTENZIONE:

Si vende esclusivamente la scheda della prima foto.

Tutto il resto è mostrato a dimostrazione della funzionalità della scheda ed è escluso.

Essendo un dispositivo OEM è destinato a tecnici esperti.

Essendo una compravendita fra privato è esclusa qualsiasi garanzia.



------------------------------------------- ENGLISH ------------------------------------------------


I am selling this PCB board which creates a differential stereo analog output from I2S.
The board involves the use of two R2R DAC modules that I have in another entry:

https://www.ebay.it/itm/326068975578

Furthermore, the board is deprived of all discrete components so as to allow customization on the project.
A handful of TTL ports to run four DACs working in pairs in parallel.
The two left and right channels are perfectly synchronized as are the + and - outputs of the analog signal. It can also be used with a single output using only GND and + signal with the advantage of a better signal to noise ratio compared to the non-dual version.

You can see the triangular signal coming out.

The output section is made with a tube circuit. It's basically a differential adder. In the input section the coupling is DC. A capacitor is provided in the output section. Since a high gain is not necessary, it is sufficient to drive the valves with a low voltage. The circuit has been tested with 60 V of anode using two 12AU7 (ECC82) tubes but can be customized as desired.

The interface is totally in hardware logic.
It works in non-oversampling mode and accepts clock frequencies beyond the classic 44.1 Khz. In the photo you can see it working at a 384 Khz sample rate, very useful for DSD files.

Power supply 5V DC for digital, 12V DC for filaments (Heater) and 60 V for anode (High voltage).
In the photo you see the complete PCB in operation.

Excellent for building the definitive converter without integrated DACs, pure direct sound.


ATTENTION:

Only the card in the first photo is sold.
Everything else is shown to demonstrate the functionality of the card and is excluded.
Being an OEM device, it is intended for expert technicians.
Since it is a sale between a private individual, any guarantee is excluded.

FOR SHIPPING COSTS PLEASE ASK BEFORE BID.