Features:
1) Dual Independently Controlled Channels
2) Wide Signal Bandwidth: 150MHz
3) Super High Sampling Rate: 1GSamples/s
4) Deep Storage Memory: 8MSamples
5) Vertical Range: 2mV/div ~ 10V/div
6) Vertical Resolution: 8bit
7) Built-in 25MHz Arbitrary Function Generator ( On DSO2D10 & DSO2D15 Only)
8) Trigger Type: Edge, Pulse, Video, Slope, Overtime, Window, Pattern, Interval, Under Amp, UART, LIN, CAN, SPI, & IIC
9) BUS Decoding and Protocol Analysis Functions: RS232/UART, I2C, SPI, CAN, LIN, etc.
10) Versatile Data Saving Functions in Multiple Formats: Settings, Signal and Reference Waveforms, CSV File for Data Values, Waveform Snap Shots, etc.
11) Build-in Dual Channel 3-Digit Voltage Meters and One 6-Digit Frequency Counter
12) Automatic Measurements for 32 Types of Real-Time Statistic Parameters: Maximum, Minimum, Standard Deviation, etc.
13) Can Set Trigger Threshold and Measure Major Parameters Automatically
14) Remotely Controllable Through SCPI (Standard Commands for Programable Instruments)
15) USB Host/Device for Transferring Data and Connecting to a USB Equipment.
Model Seletion Guide
Model | Channel | Bandwidth | Sample Rate | Memory Depth | AFG (Arbitrary Function Generator) |
DS02C10 | 2Ch | 100MHz | 1GSa/s | 8MSamples | N/A |
DS02C15 | 2Ch | 150MHz | 1GSa/s | 8MSamples | N/A |
DS02D10 | 2Ch + 1Ch | 100MHz | 1GSa/s | 8MSamples | 1Ch |
DS02D15 | 2Ch + 1Ch | 150MHz | 1GSa/s | 8MSamples | 1Ch |
Specification
Model | DSO2D15 | DSO2D10 | DSO2C15 | DSO2C10 |
Bandwidth | 150MHz | 100MHz | 150MHz | 100MHz |
Oscilloscope Channels | 2Ch | 2Ch | 2Ch | 2Ch |
Arbitrary Function Generator | 1Ch | 1Ch | ||
Horizontal | ||||
SEC/DIV Range | 2ns/div to 100s/div, in a 1, 2, 5 sequence | |||
Delta Time Measurement Accuracy (Full Bandwidth) | Single, sampling mode ± (1 sample interval + 100ppm × reading + 0.6ns) | |||
>16 times above average ± (1 sample interval + 100ppm × reading + 0.4ns) | ||||
Sample interval = s/div ÷ 200 | ||||
Vertical | ||||
A/D Converter | 8-bit resolution, each channel sampled simultaneously | |||
VOLTS/DIV Range | 2mV/div to 10V/div at input BNC | |||
Offset Range | 2mV/div ~ 200mV/div, ±1V 500mV/div ~ 10V/div, ±50V | |||
Selectable Analog Bandwidth Limit (Typical) | 20MHz | |||
Low Frequency Response (−3db) | ≤10Hz at BNC | |||
Rising Time at BNC (Typical) | DSO2C10 | DSO2C15 | DSO2D10 | DSO2D15 |
≤3.5ns | ≤2.4ns | ≤3.5ns | ≤2.4ns | |
DC Gain Accuracy | ±3% for Normal or Average acquisition mode, 10V/div to 10mV/div | |||
±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div | ||||
Vertical Offset Accuracy | ±0.1div±2mV±1% Offset | |||
Mathematical Operation | +, −, ×, /, FFT | |||
FFT | Window Function Types: Rectangle, Hanning, Hamming, Blackman, Bartlett and Flat Top | |||
Voltage Measurement Repeatability, Average Acquisition Mode | Under the same setting and environment, ≥16 waveforms are sampled, ΔV of any two averages: ± (3% × value + 0.05 div) | |||
Note: Bandwidth reduced to 6MHz when using a 1X probe | ||||
Acquisition | ||||
Sample Rate Range | 1GSa/s (single channel), 500MSa/s (dual channels) | |||
Acquisition Modes | Normal, Peak, Average & High Resolution | |||
Waveform Interpolation | (sin x)/x | |||
Acquisition Rate (Typical) | Up to 2000 waveform per second per channel (Normal acquisition mode, no measurement) | |||
Minimum Detection Pulse Width | 2ns | |||
Single Sequence | Acquisition Mode | Acquisition Stop Time | ||
Normal, Peak Detect | Upon single acquisition on all channels simultaneously | |||
Average | After N acquisitions on all channels simultaneously, N can be set to 4, 8, 16, 32, 64 or 128 | |||
Memory Depth | Maximum 8M for single channel (4K, 40K, 400K, 4M, 8M optional) Maximum 4M for dual channels (4K, 40K, 400K, 4M optional) | |||
Trigger | ||||
Trigger Type | Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Delay, UART, LIN, CAN, SPI, lIC | |||
Trigger Level Range | ±5 divisions from the center of the screen | |||
Mode | Auto, Normal, Single | |||
Level | CH1 ~ CH2 | ±5 divisions from the center of screen | ||
EXT | 0~3.3V [CMOS] | |||
Holdoff Range | 20ns ~ 10s | |||
Trigger Level Accuracy | CH1~CH2 | 0.2 div × volts/div within ±4 divisions from the center of the screen | ||
EXT | ± (Set value × 6% + 40mV) | |||
Trigger Sensitivity | ±0.2div | |||
Edge Trigger | ||||
Slope | Rising, Falling, Rising & Faling | |||
Source | CH1 ~ CH2, Line, External | |||
Pulse Trigger | ||||
Polarity | Positive, Negative | |||
Condition | <，>，!=，= | |||
Source | CH1 ~ CH2 | |||
Pulse Width Range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
Video Trigger | ||||
Signal standard | NTSC, PAL | |||
Signal source | CH1 ~ CH2 | |||
Synchronization | ScanLine, LinrNum, OddField, EvenField and AllField | |||
Slope Trigger | ||||
Slope | Nse, Fall | |||
Condition | <, >, !=, = | |||
Source | CH1 ~ CH2 | |||
Time Range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
Overtime Trigger | ||||
Source | CH1 ~ CH2, | |||
Polarity | Positive, Negative | |||
Time range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
Window Trigger | ||||
Source | CH1 ~ CH2 | |||
Pattern Trigger | ||||
Pattern | 0: low level; 1: high level; X: ignore | |||
Level | CH1 ~ CH2 | |||
Interval Trigger | ||||
Slope | Rising, Falling | |||
Condition | <, >, !=, = | |||
Signal Source | CH1 ~ CH2 | |||
Time Range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
Under Amp Trigger | ||||
Polarity | Positive, Negative | |||
Condition | <, >, !=, = | |||
Source | CH1 ~ CH2 | |||
Time Range | 8ns ~ 10s | |||
Accuracy | 8ns | |||
UART Trigger | ||||
Condition | Start, Stop, Data, Parity Error, COM Error | |||
Source | CH1 ~ CH2 | |||
Data Format | Hex | |||
Condition | <, >, !=, = | |||
Data Length | 1 byte | |||
Data Bits Width | 5 bit, 6 bit, 7 bit, 8 bit | |||
Parity Check | None, Odd, Even | |||
Idle Level | High, Low | |||
Baud Rate (Selectable) | 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s | |||
Baud Rate (Custom) | 300bit/s ~ 334000bit/s | |||
LIN Trigger | ||||
Condition | Interval Field, Sync Field, Id field, Sync Id Error, Identifier, Id and Data | |||
Source | CH1 ~ CH2 | |||
Data Format | Hex | |||
Baud Rate (Selectable) | 110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s | |||
Baud Rate (Custom) | 300bit/s ~ 334000bit/s | |||
CAN Trigger | ||||
Condition | Start Bit, Remote Frame, Data Frame Id, Frame Id, Data Frame Id A, Error Frame, All Error, Ack Error, Overload Frame | |||
Source | CH1 ~ CH2 | |||
Data format | Hex | |||
Baud Rate (Selectable) | 10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000,1000000 | |||
Baud Rate (Custom) | 5kbit/s ~ 1Mbit/s | |||
SPI Trigger | ||||
Source (SDA/SCL) | CH1 ~ CH2 | |||
Data Format | Hex | |||
Data Length | 4, 8, 16, 24, 32 | |||
IIC Trigger | ||||
Source (SDA/SCL) | CH1~CH2 | |||
Data Format | Hex | |||
Data Index | 0~3 | |||
Condition | Start Bit, Stop Bit, No Ack, Address, Restart, Address and Data | |||
Input | ||||
Number of Channels | 2 analog channels | |||
Input Coupling | DC, AC or GND | |||
Input Impedance, DC Coupled | 20pF ± 3pF, 1MΩ ± 2% | |||
Probe Attenuation | 1X, 10X | |||
Supported Probe Attenuation Factors | 1X, 10X, 100X, 1000X | |||
Overvoltage Category | 300V CAT II | |||
Maximum Input Voltage | 300VRMS (10X) | |||
Isolation Between Channels | >40dB | |||
Delay Deviation Between Channels | <500ps | |||
Measurements | ||||
Cursors | Voltage difference between cursors: ΔV | |||
Time difference between cursors: ΔT | ||||
Reciprocal of ΔT in Hertz (1/ΔT) | ||||
Automatic Measurements | PkPk, Frequency, Average, Max, Min, Period, Vtop, Vmid, Vbase, Vamp, RMS, R-Overshoot, PeriodRms, F-Preshoot, PeriodRms, PeriodAvg, RiseTime, FallTime, +Width, −Width, +Duty, −Duty, FRR, FFF, F−Overshoot, R−preshoot, BWidth, FRF, FFR, LRR, LRF, LFR and LFF | |||
DVM | Data source | CH1, CH2 | ||
Measurement type | DC RMS, AC RMS, DC | |||
Frequency meter | hardware 6 bits frequency meter | |||
Math Operation | ||||
Source | CH1~CH2 | |||
Operator | +, −, x, /, FFT | |||
FFT | Point | 1024 | ||
Window | Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop | |||
Display | Show only or show all | |||
Vertical scale | dB, VRms | |||
Storage | ||||
Save/Recall (Non-volatile) | 9 types of files can be saved and recalled internally, including settings, waveforms, and references | |||
Save to External Memory | CSV file, BMP picture (24 bit) | |||
Arbitrary Waveform Generator | ||||
Channel | 1 | |||
Standard Waveforms | Sine, Square, Ramp, Exponential, Noise, DC | |||
Sin | Frequency range | 0.1Hz ~ 25MHz | ||
Square / Pulse | Frequency range | 0.1Hz ~ 10MHz | ||
Duty | 1% ~ 99% | |||
Triangular Wave | Frequency range | 0.1Hz ~ 1MHz | ||
Ramp | Frequency range | 0.1Hz ~ 1MHz | ||
Symmetry | 0% ~ 100% | |||
Exponential | Frequency range | 0.1Hz ~ 5MHz | ||
Noise | Bandwidth | >25MHz | ||
DC offset | Range | ±3.5V, high impedance | ||
±1.75V, 50Ω | ||||
Resolution | 100µV or 3 bits, take the greater one | |||
Accuracy | 2% (1kHz) | |||
Arbitrary waveform | Frequency Range | 1µHz ~ 25MHz | ||
Wave length | 4096 | |||
Support PC download and external memory recall | ||||
Output impedance | 50 Ω + 1%, high impedance | |||
Amplitude | Output range | 10mV ~ 7Vp-p (high impedance ) 5mV ~ 3.5Vp-p (50Ω) | ||
Amplitude accuracy | ±3dB | |||
Waveform Depth | 4KSa | |||
Frequency Resolution | 1uHz | |||
Frequency Accuracy | <10KHz,100ppm >10KHz,50ppm | |||
Modulation | FM | Modulation waveform | Sine, square, ramp | |
Modulation frequency | 1Hz ~ 50kHz | |||
Modulation deviation | 0.1Hz ~ Carrier frequency | |||
AM | Modulation waveform | Sine, square, ramp | ||
Modulation frequency | 1Hz ~ 50KHz | |||
Modulation depth | 0% ~ 120% | |||
Burst | Types of | N Cycle, Infinite | ||
Number of cycles | 1 ~ 1024 | |||
Trigger source | Manual | |||
Trigger Input Signal Source | ||||
Level | MOS | |||
Probe Compensator Output | ||||
Output Voltage (Typical) | 5V | |||
Frequency (Typical) | 1kHz ± 1% | |||
Display | ||||
Display Type | 7 inchs TFT (diagonal liquid crystal) | |||
Display Resolution | 800 (horizontal) × 480 (vertical) pixels | |||
Display Type | Point, vector | |||
Waveform Brightness | Adjustable | |||
Grid Type | Adjustable | |||
Grid Brightness | Adjustable | |||
Screen Brightness | Adjustable | |||
Display Colour | 16 million colours (24 bits true colour) | |||
Persistence time | Minimum, 1s, 5s, 10s, 30s, infinite | |||
Interface | ||||
Standard Interface | USB Host, USB Device | |||
Power Supply | ||||
Supply Voltage | 100 ~ 120VACRMS (±10%), 45Hz to 440Hz, CAT II | |||
120 ~ 240VACRMS (±10%), 45Hz to 66Hz, CAT II | ||||
Power Consumption | <15W | |||
Fuse | T2A 250VAC 4*8 | |||
Environmental | ||||
Operating Temperature | 0 to 50 °C (32 to 122 °F) | |||
Storage Temperature | −40 to +71 °C (−40 to 159.8 °F) | |||
Humidity | ≤ +104°F (≤ +40°C): ≤90% relative humidity | |||
Cooling Method | 106°F ~ 122°F (+41°C ~50°C): ≤60% relative humidity | |||
Altitude | Operating and Nonoperating | 3,000m (10,000 feet) | ||
Random Vibration | 0.31gRMS from 50Hz to 500Hz, 10 minutes on each axis | |||
Nonoperating | 2.46gRMS from 5Hz to 500Hz, 10 minutes on each axis | |||
Mechanical Shock | Operating | 50g, 11ms, half sine | ||
Mechanical | ||||
Dimension | 318 × 110 × 150mm (L × W × H) | |||
Weight | 1900g | |||
