This listing is for (2) Quantity New Replacement bushings for Mavic Freehub Bushings .0015 Minor Oversize

***Look*** Now including 1 Qty. Free Inner Seal and 1 Qty. Precision Outer Bearing spacer.  This inner seal helps prevent bushing and bearing contamination.

***THIS KIT NOW INCLUDES FREE 1 Qty. 1 Milliliter HUBDOCTOR^® Light Mineral Oil for Mavic^® Free hub bushings.  Reduce wear on your free hub bushing and pawls during installation and maintenance by keeping them properly oiled.***

For Mavic road and mtb wheels only: Ksyrium, Aksium, Cosmic, Helium, Crossmax SL-Enduro-XL- SLR-ST-29-SX-UB, Deetraks, Deemax, Crossland, Crossland, Crosstrail, Crossride UB, R-SYS, Cosmic Carbon SL, Comet Route, Speedcity with FTS-L and FTS-X hubs, 2001 to 2012.

Note: To determine if you have a 2013 and Up or 2001 to 2012 freehub remove the cassette.  The outer freehub bearing retainer cap will be silver for the 2013 model.  The 2012 and earlier freehub bearing retainer cap will be black.  For Mavic road and mtb wheels 2013 and Up see our 2013 and Up listings.  

Breathe New Life into Mavic® Freehubs with HubDoctor® Rebuild Kits
The cost-saving solution for rebuilding Mavic® cassette hubs.

Included with your replacement kit are step-by-step installation instructions, with photos, that walk you through every step, so it makes it easy to service your own freehub!

Does your rear hub make a loud howl while coasting? Is the rear hub binding and turning in to a fixed gear? Grab the cassette and check side to side play. If it's more than two sprocket thicknesses and your freehub howls then your hub bushing is worn out! No Worries!  The new Hub Doctor inner bushing replacement will fix your hub for a fraction of the cost of a new one!

The Mavic Crossmax freehub standard sized (.000) bushing is for hubs with little or no measurable wear on the inner aluminum hub (.985"-.984", 25.01-24.99mm) The Mavic Crossmax Minor Oversized (.0015) freehub bushing is slightly oversized is for hubs with minor wear (.983"-.982", 24.96-24.94mm).  This will save you time compared to installing a .003" oversize bushing and sanding it to fit. You will also get more life comparded to installing a .000 standard bushing on a hub with moderate to heavy wear. 

The HubDoctor new inner bushings are manufactured out of state of the art plastic and are tested and proven to last up to 2 times longer than the original bushing. Now with 10% longer length and 50% thicker flange, fits perfectly and is twice as dense as the competition and much stiffer. (PV9700 rated).  Compared to plain clear Nylon, this material is stronger; lower friction coefficient or friction .1%; more heat and wear resistant, and will not absorb water, Nylon can absorb up to 13% compared to 0.3% for our bearing. And our bearing is made completely round on the flange so it fits just like the original part!

How to determine what size replacement bushing to purchase: 

To see which bushing size to purchase, standard .000, .0015 or .003 oversized, take the freehub off the rear wheel and measure the hub surface next to the rubber seal which is all the way inside the hub. A digital caliper or 2" micrometer works best.  If your hub measures .985-.984" order the standard size. If your hub measures .983-.982 then a .0015" oversized bushing will fit best. If your hub measures, 982-.979 the .003 oversized bushing fits best (in my other kits).

What if I’m unsure of the measurement?

I suggest purchasing our kit that contains both the standard and oversized bushing to see which bushing fits best.  Start with installing the standard bushing first and go to the .003 in needed.

What if my bushing measurements don’t fit this range? 

What if my hub has extreme wear?

Check out our .005 oversize bushing or the HubDoctor Pro ball bearing convertion kit.

Check our listing for the new HD Pro kit. (The hub picture on the right in the listing shows a case of extreme wear.)  If your hub has extreme wear, in order to save the hub, and avoid the cost of a new one, its best to purchase the HD Pro.