PLEASE NOTE THAT DELIVERY TIMES ARE AN ESTIMATE AND MAY BE DELAYED DUE TO CURRENT INDUSTRIAL ACTION BY PARCELFORCE AND ROYAL MAIL. IF YOU ARE WORKING ON A TIGHT SCHEDULE WE WOULD SUGGEST CONTACTING US PRIOR TO PURCHASE.F.Ball & Co Vinyl flooring adhesive
F44
1 litre = 4m2
2.5 litre =10m2
5 litre =20m2
Free postage to mainland uk
Product data
introduction
StYccoBond F44 is a solvent free acrylic emulsion adhesive, which is designed to give a high bond strength, strong initial tack and a long open time. It is protected against bio-degradation and is suitable for use over normal underfloor heating installations.
STYCCOBOND F44 can be used for securing vinyl sheet and tile floorcoverings to EN654, EN649 and EN651; rubber floorcoverings and some textile floorcoverings with PVC and polyurethane foam backings.
STYCCOBOND F44 can also be used in conjunction with STYCCOBOND F2 Release Adhesive to provide a RELEASE BOND system.
See the STYCCOBOND Recommended Adhesives Guide for details of specific floorcoverings.
STYCCOBOND F44 has been tested to the standards of the International Maritime Organisation and approved for use in marine floor installations by DNV - Det Norske Veritas.
STYCCOBOND F44 can be applied to STOPGAP smoothing underlayments, structurally sound, smooth, dry subfloors of concrete and sand/cement screed, plywood, flooring grade chipboard and hardboard.
STOPGAP Waterproof Surface Membranes and sound flooring grade asphalt must be skimmed with a minimum of 3mm of the appropriate STOPGAP smoothing underlayment.
For details on other subfloors, contact our Technical Services Department.
tEcHnicaL inForMation
Colour
Cream / Yellow
Consistency
Viscous Liquid
Coverage Rate (Approx.)
4m2 per litre using a 1.5mm x 5mm trowel
Open Time
Up to 60 minutes depending on temperature, humidity and absorbency of the subfloor
FEaturES
• Provides a permanent or release bond • Solvent Free • High bond strength • Approved for marine use
StandardS
All aspects of the installation of floorcoverings should be in accordance with the requirements of the relevant British Standard Code of Practice i.e. BS 8203 (Installation of resilient floorcoverings) or BS 5325 (Installation of textile floorcoverings) and supplementary specifications.
PackagES
15 litre bucket 5 litre bucket 2.5 litre bucket
1 litre pot
HoW MucH MatEriaL?
Note: Coverage rates will depend on the condition and absorbency of the subfloor.
Pack SiZE
troWEL SiZE
coVEragE PEr unit
15 litres
1.5mm x 5mm
60m2
5 litres
1.5mm x 5mm
20m2
2.5 litres
1.5mm x 5mm
10m2
1 litre
1.5mm x 5mm
4m2
QCP 2301SurFacE PrEParation
Proper subfloor preparation is essential for the correct installation of any floorcovering. Subfloors must be structurally sound, smooth, dry (<75% RH) and free from laitance and any contaminants which will affect adhesion. Use STYCCOCLEAN C140 for removing grease, oil, polish, soap etc. from non-absorbent substrates.
Concrete and sand/cement screeds must be fully cured and any laitance or surface treatments must be removed. The temperature of the floor must be maintained above 10°C throughout the application and drying of the adhesive. Underfloor heating must be off for at least 48 hours before, during and after application.
For detailed information, request the F. Ball Subfloor Preparation Guide.
daMP SuBFLoorS
The Relative Humidity (RH) of the subfloor can be measured using the F. Ball Digital Hygrometer. Where the RH value is greater than 75% the appropriate STOPGAP Waterproof Surface Membrane should be applied.
SMootHing
To ensure a level surface on which to adhere to, uneven and irregular surfaces should be suitably prepared using the appropriate STOPGAP smoothing underlayment
PLEASE NOTE THAT DUE TO CURRENT CONDITIONS PARCELFORCE ARE EXPERIENCING A LARGE INCREASE IN PARCELS AND A DECREASE IN AVAILABLE STAFF. THERE MAY BE A DELAY IN THE DELIVERY OF YOUR PARCEL. PLEASE ALLOW EXTRA TIME THAN THE ONE CURRENTLY QUOTED BY EBAY.
PLEASE NOTE THAT DUE TO CURRENT SITUATION WE HAVE HAD TO IN SOME CASES APPLY A POSTAL SURCHARGE. THIS IS DUE TO COURIER RULE CHANGES.