eBay

Professional Enamel Repair Kit
UK STOCK
Order before 1pm for same day dispatch
Royal mail 1st class shipping

This Kit contains:
Two epoxy components: 20g + 4g
Mixing Cup, Spoon, Polythene foil, Transparent Foil, Sandpaper, Full instructions.

Enamel Ceramics Fix can repair:
-Enamel (Steel/Cast Baths)
-Acrylic (Baths)
-Ceramic (Sanitary ware)
-Resin Stone (Shower trays)
-Fibreglass (Baths)

Enamel Ceramics Fix is resistant to:
-scratches
-aggressive chemical agents
-acid
-caustic cleaning agents
-temperatures from -40°C to 100°C
-UV Radiation

Please note that due to postal charges being over three times more expensive for posting sealed kit- due to the size of plastic blister packaging. To provide great price, kit is posted unsealed (please check the photo), however tubes of component are still sealed ,still new, unopened and unused.

ADVANTAGES:

Strongly binds the broken pieces of ceramic and enamel.
It's resistant to water and a variety of harsh chemicals (including detergents and solvents).
Enamel Fix does not reduce its volume during the cure
Resistant to temperatures from -40 to +100 °C.
Dope has the most optimal shade of white and very high gloss
The resulting coating is resistant to scratches

FEATURES:

epoxide basis
does not contain solvents
universal
water and temperature resistant
resistant to aggressive chemical agents
when dry, can be mechanically processed
based on non-yellowing resin
high content of pigments

USAGE:

Enamel can be used for:

repair of acrylic, ceramic, enamelled bath
repair of a washbasin, shower base, sink
repair of urinal, toilet
repair of broken tiles

but also to repair the bodies of washing machines, refrigerators, gas cookers, lacquered furniture.

ADVANTAGES:

high ability of protection against corrosion
safe when used
connects metals, ceramics, plastics
to be used both inside and outside
resistant to washing means
allows to aesthetically restore damaged elements
durable colour, resistant to ageing
high coverage capacity

Usage:

Clean and degrease the surfaces.
Squeeze from the tube into a plastic bowl 5 grams of enamel - up to internal rim of the bowl.
Cut the ending (4mm) of applicator (B ingredient) with a knife, and to already put mortar introduce 30 drops (1 gm) of solidification agent.
Then precisely mix the composite ingredients with a spoon (for at least 2 minutes).
There is a sticker made of polyethylene foil in the package. The sticker serves to make even edges, and to protect not damages surface against getting dirty by mortar.
the hole with proper size shall be cut out in the sticker, adjusted to the damaged defect, remove protective paper and stick it prior to put enamel.
Excessive composite applied with a spoon to shall be collected and equally distributed (to get even, flat surface - without excessive).
One needs to remember to remove protective sticker right after partial drying of the mortar (that is, no later than approx. 30 minutes since its application). But clear polyethylene foil allows to get smooth and glare surface.
Foil is applied on the surface, covered with mortar (immediately after removal of protective sticker) and after delicate smoothing with fingers, then it is kept to complete solidification of composite.
On vertical surfaces (to avoid flowing down of the thicker layer of enamel), the mortar shall be applied with thinner layers, after the previous one is solidified, that is every 2 hours. Scratches and cracks to be filled using i.e. toothpick. In order to receive smooth, glare surface one must remember to gently apply onto the final, last not solidified layer of mortar clear smoothing foil, and remove it only after 24 h.

TIPS AND RECOMMENDATIONS:

heat the product to room temperature prior to mixing the ingredients
do not use to connect / fill in PP, PE and PTFE.
the surface to be repaired shall be cleaned from corrosion and loosely connected old background, and then carefully degrease and dry,
it is also recommended to dim it with small sandpaper, taking care not to scratch the non-repaired surface