eBay

gws led logo

infinity pir led floodlight

INF-P SERIES: Advanced Push-FIT PIR Sensor

• Casing Colour: Black, White or Grey

• Wire Length: Approx.100cm

• Input Voltage: AC220-240V

• Beam Angle: 120 Degrees

• Lifespan: 30,000 Hours

• IP Rating: IP65 (Waterproof)

• Warranty: 3 Years

This model can be used with sensor or without as a classic floodlight. PIR floodlights are activated by movement, emitting light only when required and giving an additional level of security to residential and commercial premises. There are three colours built-in the floodlight, which enables you to change colours arbitrarily.

	10W	20W	30W	50W	70W	100W	150W	200W
Equiv. Halogen	80W-100W	150W-200W	250W-300W	350W-400W	500W-600W	700W-800W	1300W-1400W	1800W-1900W
Lumens	900-1000	1800-2000	2700-3000	4500-5000	6300-7000	9000-10000	13500-15000	18000-20000
Dimension (LWH)mm	1109020	1109020	14011025	20014527	21515725	27520530	31323330	38028240

Casing Colour


BLACK	GREY	WHITE

How to change the colour?

* Colour Setting can be done with or without PIR sensor attached.

A. Installed Without Switch: To set the colour, unit will need to be switched off and back on from the mains within 3 seconds.

B. With Switch: To set the colour on the light, simply follow instructions below:


6000K 1. Default when first turned on would be Daylight (6000K).	3000K 2. Turn off unit and switch unit back on within 3 seconds to give Warm White (3000K).	4000K 3. Turn off unit and switch unit back on again within 3 seconds to give Neutral White (4000K).

How to set the PIR sensor?

The Time, Sensitivity and the Lux level are adjusted with the dials on the PIR sensor.

Turn the TIME dial anticlockwise to decrease the hold time (7 seconds－7 minutes).
Turn the SENS dial anticlockwise to decrease the detection range (8m±2m).
Turn the LUX dial anticlockwise to restrict activation to lower light conditions (<10-2000lux).

Note: When first switched on, the light will come on for approx. 20 seconds before entering sensor mode.

infinity dtd led floodlight

INF-P SERIES: Advanced Push-FIT Dusk Till Dawn Sensor

• Casing Colour: Black, White or Grey

• Wire Length: Approx.100cm

• Input Voltage: AC220-240V

• Beam Angle: 120 Degrees

• Lifespan: 30,000 Hours

• IP Rating: IP65 (Waterproof)

• Warranty: 3 Years

	10W	20W	30W	50W	70W	100W	150W	200W
Equiv. Halogen	80W-100W	150W-200W	250W-300W	350W-400W	500W-600W	700W-800W	1300W-1400W	1800W-1900W
Lumens	900-1000	1800-2000	2700-3000	4500-5000	6300-7000	9000-10000	13500-15000	18000-20000
Dimension (LWH)mm	1109020	1109020	14011025	20014527	21515725	27520530	31323330	38028240

This model can be used with sensor or without as a classic floodlight. The dusk till dawn sensor will automatically switch the floodlight on when the ambient light level drop below 10Lux and turn off when it rises above 40Lux. There are three colours built-in the floodlight, which enables you to change colours arbitrarily.

Casing Colour


BLACK	GREY	WHITE

How to change the colour?

* Do not attach sensor, keep original blanking plug and cap in the unit when setting colour.

A. Installed Without Switch: To set the colour, unit will need to be switched off and back on from the mains within 3 seconds.

B. With Switch: To set the colour on the light, simply follow instructions below:


6000K 1. Default when first turned on would be Daylight (6000K).	3000K 2. Turn off unit and switch unit back on within 3 seconds to give Warm White (3000K).	4000K 3. Turn off unit and switch unit back on again within 3 seconds to give Neutral White (4000K).

Sensor Installation

Before fitting a sensor, turn off and isolate the floodlight to be worked on by removing the fuse or switching the circuit breaker off at the distribution board. Rotate the cap on sensor mounting anticlockwise a ¼ turn and remove (1). Pull out the blanking plug (2). Align the pins on the sensor with the holes, taking care that the bump on the inside of the collar also lines up with the slot on the mounting, then push to fit and rotate the collar clockwise a ¼ turn to seal (3).
We would advise, before permanently installing the light, is to turn the unit on and pre-select the desired colour output. Especially, if you have multiple units on a single switch, in an event that one unit may have a different sequence preset. For example, if you have 3 units installed onto a single switch, if colours on each are not pre-selected, they may differ from one another, you would not be able to synchronise the 3 units as they all have memory function.


About Us G.W.S LED is a UK-based developer and manufacturer of LED lighting, offering a broad variety of LED products for lighting professionals as well as end users. Our products undergo a certified quality standards procedure to make sure we only stock items with the newest and most reliable technology.	Payment Our preferred method would be Paypal but we can also accept all major credit/debit cards payment and direct bank transfers. If you use e-cheque on PayPal, delivery may take longer, as we will not be able to process your order until the e-cheque clears. We are a VAT registered company so a VAT receipt can be provided with your purchase.	Shipping Items will be shipped within 1-2 business days (Monday-Friday) following order completion. We offer Free UK Standard Delivery. However, if you simply can’t wait to get your hands on the product, we have Express Delivery option available for you.	Returns If the items we sent to you is incorrect, or your items have arrived with a manufacturing defect, please contact us within 14 days where we will always offer you the choice of an exchange or refund. If you wish to return unused goods for refund or exchange, they must be returned with their original packaging within 30 days. We will only pay the postage price for any goods that need to be resent due to a fault on our behalf.