FAST AND FREE
SHIPPING ON SOME OF THE ITEMS
Trusted Store
USA Seller & Secure Packaging
30 Days
Money Back Guarantee
12VDC 24VDC High Current Relay Module for Dual or Single Axis Solar Panel Sun Tracker Controller Board for DIY Projects
1. Introduction
High Current Module Features
1. Support 12VDC or 24VDC or can be used for other DC motor voltages.
2. ADD ON as a plug in for any sun tracking controller either new or existing projects
3. Thick (3mm) traces on PCB
4. Protects the controller PCB/PCBA and its components from high current transients or over current
5. Use 12VDC relay, no voltage drop
6. Use it for heavy duty DC motors up to 10 Amp
7. Small form factor to fit to a smaller box/case
8. Easy Installation, just plug it between the motor and controller board and follow on PCBA instructions
9. Compatible with any H Bridge
10. On Board 10 Amp Replaceable fuse
The High Current Module (HCM) is an input from actual field feedback thanks to HARI JAMGOSSIAN from his solar panel sun tracking project he was working on. The module was design
as a stand alone module that can be added easily to new or existing projects, it help to reduces the stress due to high current load from axial or linear DC motors using to rotate the solar panels heavy . load. Now it's even better, and safer than before with the on board 10 Amp replaceable fuse
Solar Panel Sunlight Tracker Controller advance technology, SMD low profile components, small size, with double heat sink, solid state high power MOSFETs. Required for hobbies, DIY projects, sunlight tracking, high quality etc... I'm using one from my own design at my garden, see pictures and movie clip.
I designed and fabricated this Sun tracking controller as a lesson learnt from my Solar Panel DIY project. I used controller for dual axis that I purchased on line, two of them actually stopped operating after several months mainly due to overheating causing the leads to "melt". In my design I added front and back heat sink as well as designing thick traces for the power lines. I also selected a comparator chip for extended temperature and made the PCB covered with white solder mask that should reduce a little bit the internal heat due to direct sunlight. I'm offering the controller with relatively comfortable price to the benefit of DIY hobbyists like me.
The design has two flavors, single axis or dual axis, i.e. one board with single sun tracking to control East/West or North/South and one with double axis to control West/East and North/South.
The sun tracker controller is supporting the most common application of 12VDC +/-20% from a battery, or any other power supply source.
The controller uses H-Bridge that drives the motor in either direction, i.e. clockwise/anticlockwise, left/right or up/down according to the sun location. The controller dose not repositions for the morning automatically at night, it uses the LED's field of view so that in the morning the east sensor will drive the motor and reposition to point of the morning sun as long as the sun is visible to the controller. The design can work with only one LED, I put two LEDs for each compass direction to allow more flexible field of view since these LEDs have narrow angle field of view. Using the LEDs one can catch more field of view, i.e. skew lightly the LEDs such that each LED will cover more angle, this will ensure smoother operation.
Please visit my YouTube Channel to see it working, URL: https://youtu.be/f_Z05bQw1kI?list=PL9n6C-MsF_W1AVWEN5f6w1MnkDQShryZh
You may like my other listing:
DIY Tiny Metal Detector 1"/25mm x 1"/25mm: https://www.ebay.com/itm/332836214831
DIY Proto Breadboard PCB White or Yellow: https://www.ebay.com/itm/333234608146
DIY Proto Breadboard PCB with Proto Build of H-Bridge Project: https://youtu.be/YdZrKbVN09c
DIY Sensors Board Module: https://www.ebay.com/itm/333405257471
DIY Heat Temp Module: https://www.ebay.com/itm/333409364670
DIY Dark Light Module: https://www.ebay.com/itm/333409321972
2. HCM Parameter
# | Parameter | Value |
1 | Name | Support Single or Dual Axis Sun Tracker Controller Board |
2 | Operating Voltage | DC 12V±20%, voltage source can be for example a car battery, Power Supply etc If needed to operate the motor with 24 voltage then need two sources one 12VDC for the Controller and separate 24VDC to the HCM for, example two in serial car battery |
3 | Operating Current | 15 mA (no load) |
4 | Standby Current | 1 mA (no load) controller + HCM |
5 | Drive Current | 10 Amp |
6 | Sensitivity | The sensor is calibrated and tested prior shipping |
7 | Dimensions | 42mm x 39mm x 15.7mm, 1.65in x 1.4in x 0.61in (LxWxH) |
8 | Water Resistant | No protection, need a sealed Transparent Dome, Jar, or other method to protect the controller board and also see the sunlight |
9 | Motor | Any DC Motor, axial or linear, with the limitation of the load and current that this controller can drive. For best operation must have a limiting switch for end of move. Usually linear motors have built in limit switch |
10 | Reverse Voltage | Dual/Single Axis Design - Full Reverse Voltage Controller Board Protection |
10 | Over Current | Dual/Single Axis Design - Full Over Current Controller Board Protection with replaceable on board fuse |
3. Application
The applications for the controller are a matter of how wild or creative you are J
# | Type |
1 | Solar Panel / Solar Air |
2 | Sun Tracking for Science Sensors |
3 | Solar Collector |
4 | Solar Reflector |
5 | Improve energy harvesting |
6 | Improve water heating |
7 | Follow the sun through a single axis or dual axis |
8 | School Projects |
9 | Student equipment development and design |
10 | Electronic Product Design |
11 | Play equipment development |
12 | Robots / Car Toys |
13 | Automatic light source detection |
14 | Auto Control for Electric Shading |
15 | AC/Cooling system based on the sun location |
4. Instructions
Please follow up wiring pinout attached in the pictures list for safe installation
5. Power Source
The Solar Panel Sun Tracking Controller is powered by using DC 12V +/-20%. The voltage source can be for example a car battery, Power Supply, an array of batteries etc
The High Current Relay Module is powered by the controller board, yet the DC motor can be power separately by 12VDC or 24VDC but also other voltages higher or lower as needed. the voltage is passing thru the relay contacts.
6. What in the Box
1. 1x High Current Module or per order
7. Payment
· Please make sure your eBay address is correct
· Now with Payoneer we accept Credit/Debit Cards, PayPal etc...
· We are not responsible for any tax or duty incurred by overseas customs. Please see what is right for you before purchasing.
8. Feedback
· Feedback is extremely important to us and eBay, if you are satisfied with our transaction, please take a moment to leave Positive Feedback
· YOUR Satisfaction is our #1 Priority!
9. Contact Us
· If you have any concerns about your order, PLEASE contact us through eBay message or e-mail to resolve any issues BEFORE leaving a natural rating, negative feedback or opening a dispute. We will reply within 2 business days (public holidays not included)
We have free shipping on some of our products, mainly we ship by economy domestic and international, in case you have a special request please send us a message before buying the product
We only ship to verified PayPal addresses worldwide, if you need to change the address please do it before purchasing the product.
Your order will be shipped within 1 to 3 business days once your payment received. Will ship registered mail with tracking number. The shipping to USA and other international destinations usually takes 15 -25 business days to deliver. Still, if from some reason that is out of my control you haven?t received it after 40 days business days, PLEASE contact us, we will provide you a solution.
If you have any concerns about your order, PLEASE contact us through eBay message or e-mail to resolve any issues BEFORE leaving a natural rating, negative feedback or opening a dispute. We will reply within 2 business days (public holidays not included).
We are not responsible for any tax, or customs duty incurred at foreign customs, please look what right for you before buying.
We have the policy of Returns and a refund will be given as money back or item exchanged within 30 days of delivery. For this, the article must arrive in the same conditions in which you received it. The buyer is responsible for the cost of shipping.
Welcome to your eBay "Hobbiz Electronic by BONLAF Store", there are wide variety of items that wait for you, new and used in excellent condition, items for your hobbies that will support your DIY projects you eager to complete. You can find Top Quality Proto Breadboards Kits, Metal Detectors Assembled Kits, Affordable Price Sun Tracking Controllers for Solar Energy harvesting and more opportunities for you. Customized orders are welcomed. Our products sell well in North America, Latin America Europe and Middle East. Our company insists on the principle of "Continuous Improvements, Innovation the top quality and competitive price".
We know that we are not the only ones, so we decided to do it in the best way and thus achieve your satisfaction, which is our reason for being here.
Join Our Exclusive Newsletter For Up To Date News, Special Offers And New Arrivals
Sign up NowCopyright 2019 Hobbiz Electronics. All Rights Reserved