*Scrubber Bridge is not compatible with any V shaped CatGenie drain outlets. If you have this design, please let me know and I will include Bowl Rollers and Bowl Washers instead. If you fail to alert me of your V drain, then I will refund 50% of the cost of the bridge ($7.22)
**US Federal Laws and Regulations prevents this item from being returned if it is used

Purchase all Cat Genie modifications I have designed with 1 convenient listing and with an applied 15% discount! If you have pricing questions or concerns, please feel free to send me a message! All products can be purchased individually for the price listed below the name, though you will get the applied discount with this listing


Double Scrubber:

$14.99 -> about $12.74
I know your CatGenie factory scrubber is bent and in terrible condition! The factory scrubber is made of a very low quality plastic and it quickly becomes deformed after it clips the drainage port inside the CatGenie! 

This upgraded scrubber will perform better than the factory scrubber!  The Quad-Offset design allows for 2 extra scrub mountains (9 as opposed to 7), which creates a 1-4-4 offset instead of a 1-6 offset.  The 2023 Double Scrubber is manfacturered with HIGH strength PETG plastic and it's scrub mountain formation will allow the scrubber to clean the interior of the CatGenie more efficiently allowing for a cleaner machine with every wash cycle!

The Double Scrubber was specifically designed to clip the drainage port as few times as possible! The bottom of the Double Scrubber was specifically designed with a double fillet; for a total of 3mm! Drainage clipping in inevitable, but this design will minimize clipping, and if the Double Scrubber does clip the drain, the Quad-Offset rigidity bracing will force to Double Scrubber to immediately spring back to the form factor in which it was designed! 

This 3D printed unit is manufactured with a high durability premium PLA which offers high layer adhesion and premium rigidity without a flexural modulus value too great to allow bending during unfortunate drainage clipping! This model is solid plastic through the entire unit, unlike the factory scrubber which has visible hollow points!

The Double Scrubber can be delivered in any color, however black is the standard, and if another color is desired, a surcharge and a 2+ day delay in ship time could incur. Please feel free to message me for more details! :)

Note: (1) Due to the the 9 scrub mountains being a complex geometry for 3D print manufacturing, some units might ship with sanding marks (to remove stringing and "zits") and should be assumed acceptable. Most units will not contain these defects, but units that do contain these defects will not suffer in performance. Sanding marks may make the unit appear as though it is not new, but all units are NEW and shipped as such.


Scrubber Bridge

$16.99 -> about $14.45
The Scrubber Bridge is a custom designed product in order to keep the basin of the CatGenie clean by allowing your scrubber to work more efficiently. The Scrubber Bridge will also lengthen the life of your scrubber by allowing the scrubber to pass over the basin drain with ease!

The Scrubber Bridge is designed with 49 drain holes to ensure that no waste gets stuck in or between the drain and the bridge! 

Testing has shown this product will limit the smell of the Cat Genie. The Cat Genie odor will not be removed entirely, but because the scrubber can clean the basin more effectively there will be less dirty poo material to be "baked" during the dry cycle. 

The Scrubber Bridge can be delivered in any color, however black is the standard, and if another color is desired, a surcharge and a 2+ day delay in ship time could incur. Please feel free to message me for more details! :)

Note: (1) Due to the the 49 drain holes being a moderately complex geometry for 3D print manufacturing, some units might ship with minor defects and should be assumed acceptable. Most units will not contain these defects, but units that do contain these defects will not suffer in performance. All units are shipped BRAND NEW


Smell Shield Splash Guard

$14.99 -> about $12.74
As I was doing routine maintenance on my CatGenie, I noticed most of the bad odor was coming from the scooping and pumping cycle, so I designed the Smell Shield Splash Guard to eliminate most of the odor that cycle created! 
Please note that if cat feces remains within the plastic pellets after the scoop cycle, the CatGenie will produce an unpleasant odor during the drying cycle.

In order to properly pump all of the solids out of the CatGenie, there is a crusher which crushes all of the nasty solids! The crusher is not gentle! Until the solids are small enough to fit through the output tube, the solids bounce around like popcorn inside the waste container! That bouncing creates a massive splash back of liquid/solid waste and the water the waste was sitting in! Splash back is where a portion of the smell comes from, so the Smell Shield Splash Guard is designed to prevent splashing from ever climbing up the neck of the waste basket - where the odor can escape!

On a stock CatGenie, as the solids are being crushed, microscopic waste particles are escaping through waste basket entrance and diffusing in to the ambient air because the opening is so large! Without a high powered active fan blowing around the CatGenie, this smell can linger for 20+ minutes after the cleaning cycle is complete! Yuck! The Smell Shield Splash Guard is designed to reduce this odor by making the entrance to the waste basket smaller! Due to the angled waste basket entrance, when the waste is being crushed, the microscopic particles produced are stopped by hitting the rear of the Smell Shield Splash Guard or the angle waste basket entrance, so they cannot diffuse into the air you breath! 

The Smell Shield Splash Guard can be delivered in any color, however black is the standard, and if another color is desired, a surcharge and a 2+ day delay in ship time could incur. Please feel free to message me for more details! :)

Note: (1) The Smell Shield is designed to eliminate/reduce odor, so depending on the potency of your pet's feces, an odor could exist even while using this product. Testing of the product occurred over a 14 day period, in a household with 1 pet, where some days the CatGenie was explicitly NOT cleaned in order to have extra feces inside the CatGenie. In 8 out of the 10 days the CatGenie was cleaned, the smell from the scooping/pumping cycle was removed entirely. (2) The Smell Shield is not designed to remove odor from the drying cycle. If the soap being used in your CatGenie is refilled and does not contain a strong scent, there is a chance the drying cycle can still produce an odor. In testing, the drying cycle still presented a slight odor, but it diffused away very quickly and it was not nearly as offensive as the scooping/pumping cycle.


Efficiency Scooper

$9.99 -> about $8.49
This is my second Cat Genie modification and contribution to the community! The Efficiency Scooper is a 3rd party solution designed and manufactured by me. 

The triangular truss design is designed for support against the lateral forces exerted onto the Efficiency Scooper by the Cat Genie during any hand movement action the Cat Genie makes. The triangular truss design also eliminates small crevasses where cat feces can get stuck - creating unpleasant odors! The Efficiency Scooper is designed with a unique 90 degree angled press fit bracket for a NO HARDWARE REQUIRED installation, which means you will not be required to drill holes in your Cat Genie during installation. This design decision allows you to quickly and easily remove your Efficiency Scooper, should you still desire to clean the product on occasion -without compromising performance.


The Efficiency Scooper can be delivered in any color, however black is the standard, and if another color is desired, a surcharge and a 2+ day delay in ship time could incur. Please feel free to message me for more details! :)

Shipping: The Efficiency Scooper will ship next day in most scenarios. During periods of high volume I may need extra time to print/prepare the product; should the product be estimated to ship in a 3+ day window, I will PM the buyer to confirm the order. 

Note: (1) Most prints will be near perfect, however minor defects should be assumed acceptable. Defects that prevent functionality of the product will be culled.