M12 Loose Bolt High Tensile 8.8 Masonry Shield Anchor Zinc

M12, 12mm Diameter Threaded, Hex Head, Loose Bolt with Masonry Shield, Heavy Duty Masonry Anchor Fixing, High Tensile (8,8), Zinc, ZYP. Fixaball sells all lengths of M12 Loose Hex Bolt, Heavy Duty Masonry Anchors. Installation of Shield Anchors When drilling holes you must respect the specified minimum depth and diameters shown in the table below. Holes must be square to the surface of the base material (e.g concrete) for safety during installation and to optimise holding capacity. Use the material/ fixture as a template to dill accurate locations If drilling through concrete that has rebar reinforcements, special care must be taken to avoid damaging them. If some rebar is encountered, abort the hole, repair with high quality mortar and create a new hole, no less than twice the diameter of the shield anchor, away. Optimising your fixings holding capacity. Clean the hole using an appropriate sized brush Installation Temp is 0°: make sure water does not seep into the hole. The expansion water to ice could crack the concrete. Under wet conditions, use a specified injection resin. Introduce the anchor through the material to be fixed into the hole up to the embedment depth, according to the values on the table. Use a hammer to ensure the required depth. Do not apply any intermediate layer between the material to be fixed and the washer, such as sealing products. Apply the specified torque with a torque wrench. In the case the holes on the material to be fixed have a bigger diameter than required, it is necessary to insert a thicker washer and of a bigger diameter. But please, note that this procedure does not ensure a correct distribution of shear loads amongst all the anchors of a same group, and this shear load is applied only to the anchors with a correct diameter on the material to be fixed. Orders placed before 2pm are dispatched same day (Mon-Fri). Standard, Free Delivery is Royal Mail, 2nd Class (2-5 days, most likely 2 days). For a faster delivery time, select 1st class or courier at checkout. . Postage upgrades available at checkout for time sensitive deliveries. Please make your 'no of items in pack', 'length', and 'quantity', of packs selection from the drop down menus. Important Loose Bolt Anchor Performance Dimensions Thread Diameter of Hex Bolt Shield Hole Size Max Fix.Thickness M12 20mm 10mm M12 20mm 25mm M12 20mm 40mm M12 20mm 60mm NOTE: the 1st dimension refers to the thread diameter and not the hole diameter. Please see the table below for further information on what masonry drill bit to use. The 2nd dimension refers to the maximum fixture thickness (space between the underside of the head and the shield +/- 5mm). The 3rd dimension is the actual length of the hex-bolt/ hex-set that goes into the sheild (in brackets). Table: Shows typical masonry shield values and measurements All measurements in Metric - mm (all lengths are taken from under the hexagan head) Thread Diameter Hole Diameter Hole Depth Fixture/ Material Clearance Hole Centre Spacing Between Holes Minimum Distance From Edge of Material Tensile/ Pull Load k/N (tonnes) Shear Load k/N (tonnes) Torque to tighten Nm M6 12 50 7 - 8 120 80 3.5 2.1 6.5 M8 14 55 9 – 10 150 100 4.8 4.4 15 M10 16 65 11 – 12 180 120 6.2 6.1 27 M12 20 85 13 – 14 250 160 9.7 12.4 50 M16 25 125 17 - 18 290 190 21.3 27.6 120 All specifications are true with correct installation Socket size guide:M6 - 10mm SpannerM8 - 15mm SpannerM10 - 17mm SpannerM12 - 19mm SpannerM16 - 24mm SpannerM20 - 30mm Spanner Image is for illustrative purposes only.

M12 Loose Bolt High Tensile 8.8 Masonry Shield Anchor Zinc

M12, 12mm Diameter Threaded, Hex Head, Loose Bolt with Masonry Shield, Heavy Duty Masonry Anchor Fixing, High Tensile (8,8), Zinc, ZYP.

Fixaball sells all lengths of M12 Loose Hex Bolt, Heavy Duty Masonry Anchors.

Installation of Shield Anchors

When drilling holes you must respect the specified minimum depth and diameters shown in the table below. Holes must be square to the surface of the base material (e.g concrete) for safety during installation and to optimise holding capacity. Use the material/ fixture as a template to dill accurate locations

If drilling through concrete that has rebar reinforcements, special care must be taken to avoid damaging them. If some rebar is encountered, abort the hole, repair with high quality mortar and create a new hole, no less than twice the diameter of the shield anchor, away.

Optimising your fixings holding capacity.

  • Clean the hole using an appropriate sized brush
  • Installation Temp is 0°: make sure water does not seep into the hole. The expansion water to ice could crack the concrete. Under wet conditions, use a specified injection resin.
  • Introduce the anchor through the material to be fixed into the hole up to the embedment depth, according to the values on the table. Use a hammer to ensure the required depth. Do not apply any intermediate layer between the material to be fixed and the washer, such as sealing products.
  • Apply the specified torque with a torque wrench.
  • In the case the holes on the material to be fixed have a bigger diameter than required, it is necessary to insert a thicker washer and of a bigger diameter. But please, note that this procedure does not ensure a correct distribution of shear loads amongst all the anchors of a same group, and this shear load is applied only to the anchors with a correct diameter on the material to be fixed.

 

Orders placed before 2pm are dispatched same day (Mon-Fri).

Standard, Free Delivery is Royal Mail, 2nd Class (2-5 days, most likely 2 days). For a faster delivery time, select 1st class or courier at checkout. . Postage upgrades available at checkout for time sensitive deliveries.

Please make your 'no of items in pack', 'length', and 'quantity', of packs selection from the drop down menus.

 

Important Loose Bolt Anchor Performance Dimensions

Thread Diameter of Hex Bolt Shield Hole Size Max Fix.Thickness
M12 20mm 10mm
M12 20mm 25mm
M12 20mm 40mm
M12 20mm 60mm

 

NOTE: the 1st dimension refers to the thread diameter and not the hole diameter. Please see the table below for further information on what masonry drill bit to use. The 2nd dimension refers to the maximum fixture thickness (space between the underside of the head and the shield +/- 5mm). The 3rd dimension is the actual length of the hex-bolt/ hex-set that goes into the sheild (in brackets).


    Table: Shows typical masonry shield values and measurements

    All measurements in Metric - mm (all lengths are taken from under the hexagan head)

    Thread Diameter

    Hole Diameter

    Hole Depth

    Fixture/ Material Clearance Hole

    Centre Spacing Between Holes

    Minimum Distance From Edge of Material

    Tensile/ Pull Load

    k/N (tonnes)

    Shear Load k/N (tonnes)

    Torque to tighten Nm

    M6

    12

    50

    7 - 8

    120

    80

    3.5

    2.1

    6.5

    M8

    14

    55

    9 – 10

    150

    100

    4.8

    4.4

    15

    M10

    16

    65

    11 – 12

    180

    120

    6.2

    6.1

    27

    M12

    20

    85

    13 – 14

    250

    160

    9.7

    12.4

    50

    M16

    25

    125

    17 - 18

    290

    190

    21.3

    27.6

    120

    All specifications are true with correct installation

     

    Socket size guide:
    M6 - 10mm Spanner
    M8 - 15mm Spanner
    M10 - 17mm Spanner
    M12 - 19mm Spanner
    M16 - 24mm Spanner
    M20 - 30mm Spanner

    Image is for illustrative purposes only.

     

    ×
    ×
    ×
    ×

    Tell a friend Visit store Watch now

    Postage info

    Click the Postage tab above the listing description for more info

    Additional delivery notes

    PICK UP OPTION

    Sorry, our items are NOT available for pick-up.

    PAYING VIA PAYPAL


    We accept PayPal on our all our items so you can shop with confidence.

    Simple choose the PayPal option when proceeding through the checkout.

    Paying via Direct Deposit

    Simply add the freight cost to the item cost and forward the total amount to the address to be provided following your purchase.

    Additional Information

    No additional information at this time

    Ask seller a question

    To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

    Ask seller a question

    © Fixaball

    Click the Postage tab above the listing description for more info

    Accepted Payment Methods

    • PayPal
    • Direct Deposit

    Returns are accepted

    Items must be returned within 30 days of the auction ending

    Buyer will pay for return shipping.


    Additional Information:
    Returns 'NO QUIBBLE' Our returns policy lasts 30 days. If 30 days have gone by since delivery, unfortunately we can’t offer you a refund or exchange (+ a couple of days, grace). To be eligible for a return, your item must be unuséd and in the same condition that you received it. It must also be in the original packaging with original documentation. A restocking fee of 15% will be applied to refunds. Cost of sending the shipment is not refunded unless the wrong item was sent. To complete your return, we require a receipt, invoice or other proof of purchase. This will enable an easier process of locating and amending orders. Please keep all labels, stickers and original packaging to be eligible for free returns. Refunds (if applicable) NO QUIBBLE - We invite all people to stay with us as their preferred supplier of fixings and fasteners. If you're not happy, we will do everything possible to help. Please, please, please keep all documents, stickers, labels and packaging; it makes the process run quicker and easier. Orders over £1000 need to be returned within 5 working days to be accepted, processed and refunded. Late or missing refunds (if applicable) If you haven’t received a refund on the day of return please contact us to verify the situation. Banks vary in their reaction time to changes; there is often some processing time before a refund is posted. Any concerns no matter how small, contact: 01242 522244 Sale items (if applicable) Only regular priced items may be refunded, unfortunately sale items cannot be refunded. Exchanges (if applicable) NO QUIBBLE - All exchanges are welcomed, assuming that items are suitable for re-sale. Please, return the item with the invoice and a note describing what you would like as an exchange. AN invoice will be sent to cover the postage to send the exchanged item. Free returns are available in the very rare event that we have sent an incorrect item. Orders over £1000 need to be returned within 5 working days to be accepted, processed and exchanged. Shipping 99% of orders are dispatched the same day as purchase if the order was made before 2pm. After 2pm your order will join the following days post. Royal Mail deliver most items up to 2kgs and Interlink Express deliver our oversized and heavier items, next day. Usually, the easy bit is getting the order out the door, but, what happens after can occasionally disappoint us both. If delivery is crucial/ time sensitive, you should select a faster and/ or signed for postage option at checkout. Mailing Disclaimer 98% (490 orders) of shipping arrives on time. 2% (10 orders) are late 1.4% (7 orders) 1 day late 0.4% (2 orders) 2 days late 0.2% (1 order) 3+ days late 0.01% is reported lost. - 1 every couple of years Our 'NO QUIBBLE' guarantee gives you peace of mind that we will accept all, undamaged returns and issue a refund, every time. If you need a definite arrival time please select an express service at check out to avoid disappointment.