KUSBA USB Accelerometer for Klipper ADXL345 by Isik's Tech

KUSBA is an all in one accelerometer solution to measure resonances for your 3D printer. With an integrated RP2040 mcu and onboard ADXL345 diy wiring and soldering is no longer required – just a USB-C to USB-A cable (Available 1.8m with/without cable). Designed by xbst / Isik’s Tech – every purchase directly supports his efforts for further research and development into this and other projects. Board are pre-flashed, if not being detected on klipper please try reset the device and re-flash more update to date kipper bin. As there many be compatible changes between different klipper version. (Holding the reset button while plugging in the device). New board is pre-flashed with "Ampon". More Info: https://github.com/xbst/KUSBA/blob/main/Docs/v2-Rampon-Firmware.md (PCB Version: V2.4) Written Documentation: https://github.com/xbst/KUSBA Install Video: https://www.youtube.com/watch?v=gtrQXdAaXB4 Printed Bracket: https://github.com/xbst/KUSBA/tree/main/Mounts Note: Mount Spacing is 30mm, if you have 30mm fan you can mount directly onto the fan using existing bolt in most case otherwise you may require longer bolt. Cad: https://github.com/xbst/KUSBA/tree/main/CAD How to Configure Klipper [mcu adxl]serial: /dev/serial/by-id/usb-Anchor_Rampon-if00[adxl345]cs_pin: adxl:CS[resonance_tester]accel_chip: adxl345probe_points: 0,0,0# Edit the above line with the correct probe points location. I recommend the center of your bed for X & Y, 20 for Z.# For 350 mm printers: 175,175,20# For 300 mm printers: 150,150,20# For 250 mm printers: 125,125,20# For 120 mm printers: 60,60,20# More info: https://www.klipper3d.org/Config_Reference.html#adxl345 Note: Module is available separately without require type c to a cable or with 1.8mm cable which is suitable for most raspberry pi.

KUSBA USB Accelerometer for Klipper ADXL345 by Isik's Tech

All Prices include GST. Message us if require a tax invoice.

KUSBA is an all in one accelerometer solution to measure resonances for your 3D printer.

With an integrated RP2040 mcu and onboard ADXL345 diy wiring and soldering is no longer required – just a USB-C to USB-A cable (Available 1.8m with/without cable). 

Designed by xbst / Isik’s Tech – every purchase directly supports his efforts for further research and development into this and other projects.

Board are pre-flashed, if not being detected on klipper please try reset the device and re-flash more update to date kipper bin. As there many be compatible changes between different klipper version. (Holding the reset button while plugging in the device). 

New board is pre-flashed with "Ampon". More Info: https://github.com/xbst/KUSBA/blob/main/Docs/v2-Rampon-Firmware.md (PCB Version: V2.4)

 

Written Documentation: https://github.com/xbst/KUSBA

Install Video: https://www.youtube.com/watch?v=gtrQXdAaXB4

Printed Bracket: https://github.com/xbst/KUSBA/tree/main/Mounts

Note: Mount Spacing is 30mm, if you have 30mm fan you can mount directly onto the fan using existing bolt in most case otherwise you may require longer bolt.

Cad: https://github.com/xbst/KUSBA/tree/main/CAD

 

How to Configure Klipper

[mcu adxl]
serial: /dev/serial/by-id/usb-Anchor_Rampon-if00

[adxl345]
cs_pin: adxl:CS

[resonance_tester]
accel_chip: adxl345
probe_points:
0,0,0
# Edit the above line with the correct probe points location. I recommend the center of your bed for X & Y, 20 for Z.
# For 350 mm printers: 175,175,20
# For 300 mm printers: 150,150,20
# For 250 mm printers: 125,125,20
# For 120 mm printers: 60,60,20

# More info: https://www.klipper3d.org/Config_Reference.html#adxl345

 

Note: Module is available separately without require type c to a cable or with 1.8mm cable which is suitable for most raspberry pi.

HAVE A QUESTION OR CONCERN? 

If you need more information regarding this item, please message us or check on original manfuacturers websites.

DREMC STORE back our products and pride ourselves, not only in quality but in genuine products. Please do not hesitate to reach out to us. We stock the largest range of 3D Printer Spares Parts, from Manufacturer such as E3D-Online, Creality, Slice Engineering, Bondtech, Micro Swiss, LDO Motors, Bigtreetech, Trianglelabs to name a few.

We are the largest Australia Creality Spare Part Distributors based in Brisbane, we stock over 200 SKUs Creality Printers spares parts. Our website store.dremc.com.au for latest stock list and accurate real time stock counter, no hidden stock levels.

Do you need bulk spare parts or DREMC / Polymaker filament discount? Message us now if you require B2B/Educational payment terms.

Please check out our feedback to see what others are saying about us. 

Postage info

Click the Postage tab above the listing description for more info

Click the Postage tab above the listing description for more info!

Additional delivery notes

PICK UP OPTION

Sorry, our items are NOT available for pick-up.

PAYING VIA PAYPAL/CARD


Please refer to eBay Checkout for available payment method.

Price include GST. Message us if require a tax invoice.

Additional Information

No additional information at this time

Ask seller a question

To contact our Customer Service Team, simply click the button here and our Customer Service team will be happy to assist.

Ask seller a question

© DREMC STORE

Click the Postage tab above the listing description for more info

Returns are accepted

Items must be returned within 30 days of the auction ending

Buyer will pay for return shipping.