ULNA CPE629 is a 1Gbps wireless bridges. It uses wireless communication technology to transmit network data using air as a medium, one as a receiver and the other as a transmitter for long-distance point-to-point or point-to-multipoint interconnection. The working data link layer realizes the interconnection of local area networks. 5.8G long distance transmission with 16DBi high gain antenna, up to 5KM. The transmission speed between 2 long range wifi bridge max is 1200Mbps.
Easy to use
1.Unbox everything
2. Switch one unit to A and one unit to B
3. Connect the POE to each unit using the Ethernet cable and plug the POE in
3. Wait for them to power up, about 2 min
4. For 5.8 gh Use the tiny reset button to click through until you get a channel with a letter. A,B,C… Then on the other unit do the same. Both units need to be on the same channel
5. You should see them sync
6. Place the unit you designated B in step 2 above at the existing WiFi point and the unit designated A at the location you are trying to establish extended WiFi
7. Plug at cable from your router to the POE then to the unit
8. At the far end plug a cable in the unit, then to the POE then another cable from the POE to your new router
9. Enjoy
Application Case1:
I have a property that has several office buildings that are spread out over 20 acres and was told that to get internet to these buildings I would have to get someone (electrician) to bury some cables to link all the buildings together or pay for the cable company (specturm) to make drops on every building. The problem with that is there is a paved road that divides the property and that was going to kill any budget to run cables.
I installed this ULNA long range wireless bridge for wifi in 1 hours start to finish with a helper. I have a 300Mbps connection and at the other end of the bridge I was getting 280Mbps. This was a distance of 800 ft but a clear site of view and about 20 ft off the ground. Now that both sides of the road have internet. Avoid digging and wiring and save me a lot of money
|
|
|
---|---|---|
Switch Master-Slave BridgeSwitch button to"A" indicates the bridge as the master bridge (transmitter), switch button to"B" indicates the bridge as the slave bridge (receiver), a pair of bridges is already preset with A and B, no need to set them again. Note that in the point-to-multipoint application, one of the bridges is used as A and the other bridges are used as B. Then set them both to the same channel number to complete the point-to-multipoint pairing |
Only One 1Gbps PortThe gigabit wifi bridge has 1 1000Mbps and 100Mbps ports, both of which can accept a 24V PoE power supply, recommended to connect a gigabit port, and the CAT 5e network cable can be used as a power cable to supply power and transmit data. DC power supply is not recommended. Tip: only the PoE port supplies power,the LAN port cannot be powered |
Rotate 360°Outdoor wifi bridge kit equipped with a universal wheel, it can rotate 360 to any angl. Easy to adjust antenna orientation for maximum signal strength |
|
|
|
---|---|---|
Elevator Monitoring ApplicationUsing a wireless ethernet bridge to transmit monitoring signals in elevator monitoring can effectively avoid cable damage and obtain stable monitoring images. The wireless bridge is easy to install, supports point-to-point and point-to-multipoint, and can be disassembled and moved to other places for use |
Watchdog FunctionBridge with watchdog function. When the Wireless Outdoor CPE Kit communication fails, the corresponding unit will automatically detect and restart, restore network communication by itself |
Package Included2 * CPE629 Gigabit Bridge 2 * Gigabit POE Adapter (24V) 2 * Cat 5e Network Cable 2 * Metal Hoop 1 * Mounting Screw Set 1 * User Manual |
|
|
|
---|---|---|
Pole Mounting1. Plug the dynamic stick into the bracket. 2. Screw the sealing nut and assembled parts, as well as tighten it. 3. Put the nock washer on the dynamic stick. 4. Assemble the mounting parts to the bridge. 5. Thread the open end of the pole strap through the two tabs on the bracket. 6. Lock and tighten pole strap to secure bracket to the pole |
Wall Mounting1. Plug the dynamic stick into the bracket 2. Screw the sealing nut and assembled parts, as well as tighten it 3. Put the nock washer on the dynamic stick. 4. Assemble the mounting parts to the bridge 5. Determine the mounting location. Mark and drill three 6. Put wall anchors into the holes and insert screw into the wall anchor. 7. Screw and secrue the bracket in the place |
FeaturesGigabit port 16dBi antenna 5.8G channel 27dBm wireless speed Transmission distance up to 5 km Support PC side to modify IP settings Dialing to set the transmitter and receiver WDS networking mode, video network dual compatibility Dynamic MIMO power saving mode (DMPS) and automatic power saving transmission (APSD) |