BFT MITTO RCB2 RCB4 Fob Gate Remote Control
FREE Battery installed in the device for your convenience!
For
BFT gates, garage doors, barriers or other BFT automation systems.
It
can be easily programmed from an existing device or from the control
panel.
BFT MITTO is not a universal transmitter, however it can be used with UNIVERSAL 433.92 MHz rolling code receivers.
How To Program BFT Mitto:
The
following process will only work if your control panel has been enabled
for remote programming by the installer. If the following process does
not work you will need the assistance of an approved BFT installer.
You must be at the control panel. (It does not need to be open).
You will need one existing, functional, transmitter already coded on the system.
and any new/replacement transmitters readily to hand.
The
following sequence must be followed sequentially in rapid succession;
any pause in the process will cause the system to time out.
Read and familiarise yourself with the process before commencing.
Programming Method:
1. Press the hidden button on the back of the transmitter already stored on the system for 2 seconds.
(If it has no hidden button use the top two front buttons together instead).
2. Press the functioning button on the front of the transmitter already stored on the system for 2 seconds.
3. Press the hidden button on the back of the new transmitter for 2 seconds.
(If it has no hidden button use the top two front buttons together instead).
4. Press the desired button on the front of the new transmitter for 2 seconds.
Repeat
3 & 4 for as many transmitters as are to be added to the system,
but ensure there is no pause between operations to prevent time out.
5. Leave 20 Seconds before attempting to use your new transmitter(s) for the board to reset.
Coding is now complete.
If this process fails to enable your new transmitter(s) contact your local approved BFT Installer.
If you need any help at all, or advice, you can call me directly. 


We have repaired over 10'000 garage doors and with over
20 years experience we know 'garage doors' 


We are only a phone-call away.
How To Program BFT Mitto:
How To Program BFT Mitto:
The
following process will only work if your control panel has been enabled
for remote programming by the installer. If the following process does
not work you will need the assistance of an approved BFT installer.
The following process will only work if your control panel has been enabled for remote programming by the installer. If the following process does not work you will need the assistance of an approved BFT installer.
You must be at the control panel. (It does not need to be open).
You must be at the control panel. (It does not need to be open).
You will need one existing, functional, transmitter already coded on the system.
You will need one existing, functional, transmitter already coded on the system.
and any new/replacement transmitters readily to hand.
and any new/replacement transmitters readily to hand.
The
following sequence must be followed sequentially in rapid succession;
any pause in the process will cause the system to time out.
The following sequence must be followed sequentially in rapid succession; any pause in the process will cause the system to time out.
Read and familiarise yourself with the process before commencing.
Programming Method:
Read and familiarise yourself with the process before commencing.
Programming Method:
1. Press the hidden button on the back of the transmitter already stored on the system for 2 seconds.
1. Press the hidden button on the back of the transmitter already stored on the system for 2 seconds.
(If it has no hidden button use the top two front buttons together instead).
(If it has no hidden button use the top two front buttons together instead).
2. Press the functioning button on the front of the transmitter already stored on the system for 2 seconds.
2. Press the functioning button on the front of the transmitter already stored on the system for 2 seconds.
3. Press the hidden button on the back of the new transmitter for 2 seconds.
3. Press the hidden button on the back of the new transmitter for 2 seconds.
(If it has no hidden button use the top two front buttons together instead).
(If it has no hidden button use the top two front buttons together instead).
4. Press the desired button on the front of the new transmitter for 2 seconds.
4. Press the desired button on the front of the new transmitter for 2 seconds.
Repeat
3 & 4 for as many transmitters as are to be added to the system,
but ensure there is no pause between operations to prevent time out.
Repeat 3 & 4 for as many transmitters as are to be added to the system, but ensure there is no pause between operations to prevent time out.
5. Leave 20 Seconds before attempting to use your new transmitter(s) for the board to reset.
5. Leave 20 Seconds before attempting to use your new transmitter(s) for the board to reset.
Coding is now complete.
Coding is now complete.
If this process fails to enable your new transmitter(s) contact your local approved BFT Installer.
If you need any help at all, or advice, you can call me directly. 


We have repaired over 10'000 garage doors and with over
20 years experience we know 'garage doors' 


We are only a phone-call away.
If this process fails to enable your new transmitter(s) contact your local approved BFT Installer.
If you need any help at all, or advice, you can call me directly. 


We have repaired over 10'000 garage doors and with over
20 years experience we know 'garage doors' 


We are only a phone-call away.