FCC ID: O44JR520AMSH

(Alternate Spelling: 044JR520AMSH 044JR52OAMSH)

Part #: 1WSHR-1600

(Interchangeable) Part #s:

Frequency: 433.5  MHz

LED color: Blue

4 buttons

Compatible with the following systems:

CM4000

CM4200DX

CM4300

CM5000

CM5200

CM6000

CM6200

CM6300

Programming Instructions:

Before you can program the remote(s) you must complete installation. Otherwise the only wires needed to program the remote(s) are the 12v (+) constant wires (red and red/white), the ground wire (black), and the ignition wire (green). You must have the antenna connected to the main controller. Here are the steps for remote programming:

STEP 1:

Turn the key in the ignition from the Off or ACC to the On or IGN position 5 times within 7 seconds. After the 5^th ignition cycle you will hear the parking light relay click. This will happen after the 5^th cycle so it is easy to miss. If you hear two relay clicks and parking light flashes, the system has just exited remote programming mode.

STEP 2:

Right after the 5^th cycle and hearing the first relay click:

A. 1-Way Remote:

Tap the lock button on the remote for 0.5 seconds.

B. 2-Way Remote:

Tap button I for 0.5 seconds. Pro 2WSSR place battery in remote.

STEP 3:

After tapping the button on the remote, you will hear the parking light

relay click once to indicate that it has accepted the remote. If you have other remotes to program to the system, repeat step 2 for each remote, one after the other. Each system can accept three remotes with the exception of the P2WS

SR.

Using a remote is a timed process so read this section in its entirety before beginning.

IMPORTANT:

Special Option Groups cannot be programmed with a remote – the OP500 must be used. If at any time during the process you hear a long siren or horn sound the system kicked you out of programming mode.

STEP 1: Select the option menu that contains the desired programming option.

To select a menu, use the following button combinations:

I+II for 2.5 sec. then

I+II for 2.5 sec.

Menu 1

I+II for 2.5 sec. then

I+IV for 2.5 sec.

Menu 2

I+IV for 2.5 sec. then I+II for 2.5 sec.

Menu 3

I+IV for 2.5 sec. then I+IV for 2.5 sec.

Menu 4

*Pro 2 Way remotes will displa

y the error number “Strt Er##” on the

LCD.

*Buttons I, II, III, IV correspond to I = Lock, 2 = Unlock, 3 = Trunk, 4 = Start on 1 Way remotes

STEP 2: After entering the option menu that contains the desired option, tap button (IV) on two-way remotes for .5 seconds and buttons (Trunk + Start) on

one-way remotes for 2.5 seconds the number of times equal to the option number.

Wait for a parking light flash and siren chirp between each button press. After selecting the desired option number, the system will confirm which option you have selected by the number of siren chirps and parking light flashes.

STEP 3:

Once the system is finished confirming the option number, set the option to the desired setting by tapping buttons I, II, III, or IV. To set options with the

one-way remote the button configuration is different. Tap the Lock Button for Setting 1, Tap the Unlock Button for Setting 2, Tap the Key Button for Setting 3, and Hold the Trunk and Key Buttons for Setting

4.Resetting to Factory Defaults:

To reset the options in a particular menu group, enter the menu by following STEP 1, then tap button III for 0.5 sec, three times. Wait for the siren to chip

and parking lights to flash between each tap. After the third tap, the option menu will reset and the siren will chirp three times. This must be done for each option group that needs to be reset

Option Programming Using the 1-way Antenna Button

Programming the main controller option using an antenna is a timed

process so you should read the instructions entirely before

beginning.

STEP 1: Turn vehicle’s ignition to the on position.

STEP 2: Selecting the Option Menu - Select the option menu that contains

the option you would like to adjust. Be aware, the special option groups are not available when programming options with an antenna. To select a menu, use the following button combinations:

Hold antenna button until you hear/see1 chirp/parking light flash.

Menu 1 Hold antenna button until you hear/see 2 chirps/parking light flashes.

Menu 2 Hold antenna button until you hear/see 3 chirps/parking light flashes.

Menu 3 Hold antenna button until you hear/see 4 chirps/parking light flashes.

Menu 4

STEP 3:

Selecting the Specific Option - After entering the option menu that contains the option you wish to change, tap the antenna button the number of times equal to the option number you wish to change. A few seconds after you have stopped selecting an option, the system will confirm which option you have selected by the number of siren chirps and parking light flashes.

STEP 4:

Setting the Option - After the system is finished confirming the option number, set the option to your desired setting by tapping the antenna button 1,2,3, or 4 times.

Resetting to Factory Defaults:

To reset the options in a menu, enter the menu as if you were going to program an option then hold the antenna button for three seconds. The option menu will reset and the siren will chirp three times. The options in the other three menus will remain set