Please stand by while rebooting the system.
Stage 1 Loader 1.0.5.0 (build 56553)
Built: 2016-09-22 at 05:02:10
Secure Boot Enabled on the Processor
Bank: Primary
CPLD: rev: 3.0 (30:0060|32:0002|33:0000|34:0000|35:0000)
PRID: 000C1203
POWER ON RESET CFG:30CC0FF2
Initialized I2C0 Controller.
Initialized I2C1 Controller.
SPD Rev:0x11 DIMM:0 Type:2 Speed:666MHz #Rank:1
DDR3: Node 0 Channel 0 Mem size = 4096 MB UDIMM
set freq:666666
DDR3: Node 0 DRAM frequency 666 MHz
DDR3: Node 0 CPU frequency 800 MHz
mtb_ps:125 clock:1500 trc:33 trcd:9 trp:9
AP3:A0CFFF0 ODTP1:10000
Board DDR VDD set to 1.5V.
N:0 CH:0 additional rdlvl rdly:1
N:0 Ch:0 m:32 s:32 R OK.
Rank:0 HW WLVL Passed Mask:1FF
AP3:A0CFFF0 ODTP1:10000
n:0 ch:0 RTT WR:0200
===N:0 Ch:0 m:32 s:32 RW OK.
Node:0 Ch:0 TGE Set Memory:4096 MB value:FF FF -- PASS
Node:0 Ch:0 TGE Set Memory:4096 MB value:FF 00 -- PASS
Node:0 Ch:0 TGE Set Memory:4096 MB value:AA 55 -- PASS
Node:0 Ch:0 TGE Set Memory:4096 MB value:00 00 -- PASS
DDR3 Initialization Passed.
NBU0 DRAM BAR0 base: 00000000 limit: 0013f000 xlate: 00000001 node: 00000000 ( 0 MB -> 320 MB, size: 320 MB)
NBU0 DRAM BAR1 base: 001d0000 limit: 00bff000 xlate: 00090001 node: 00000000 ( 464 MB -> 3072 MB, size: 2608 MB)
NBU0 DRAM BAR2 base: 00e00000 limit: 0128f000 xlate: 00290001 node: 00000000 ( 3 584 MB -> 4752 MB, size: 1168 MB)
Hit Ctrl + X keys to stop autoboot: 0
CPBoot image is signed
Verifying CPBoot checksum...
CPBoot check passed
Signer Cert OK
Policy Cert OK
RSA signature verified.
## Starting application at 0x8C100000 ...
CPBoot 1.0.7.0 (build 56553)
Built: 2016-09-22 at 04:52:12
DRAM: 4 GB
Detected [XLP208 Rev B1 (Secure Boot) ] (6a|6a)
CPLD: rev: 3.0 (30:0060|32:0002|33:0000|34:0000|35:0000)
Flash: 16 MB
PCIE (B0:D01:F0) : Link up (Gen(1))
Bank: Primary
Board: A7010
CPU: XLP208 Rev B1 (Secure Boot)
Clock: Core 800 MHz / SoC 800 MHz (30cc0ff2)
Net: ge-0, ge-2, ge-3, ge-4, ge-1
Inventory Verification: PASS
Hit Ctrl + X key to stop autoboot: 0
USB0: setting speed to USB_SPEED_HIGH
2 USB Device(s) found
#1 Storage Device(s) found
##Loading image 0:0###################################
Image is signed; verifying checksum...
passed
SHA2 Signature available
Signer Cert OK
Policy Cert OK
RSA signature verified using SHA2.
[ 0.000000] 0:xlp_napi_vc_mask 0xf
[ 0.000000] 0:sae frequency is 500
[ 0.000000] 0:nlm_hal_set_sae_engine_sel: xlp2xx return
[ 0.000000] 0:-- SAE Frequency set to 500
[ 0.000000] 0:cde frequency is 333
[ 0.000000] 0:CDE Frequency set to 333MHz
[ 0.000000] 0:MSGRING_NAPI: Initializing NLM NAPI subsystem
[21:19:02]:...Starting rcS...
Aruba Networks
ArubaOS Version 8.3.0.9 (build 72226 / label #72226)
Built by p4build@pr-hpn-build07 on 2019-09-13 at 12:50:59 UTC (gcc version 4.4.5 )
(c) Copyright 2019 Hewlett Packard Enterprise Development LP.
<<<<< Welcome to Aruba Networks - Aruba A7010-US >>>>>
[21:19:03]:Probing for EEPROM devices [ OK ]
[21:19:04]:Probing for real-time clock [ OK ]
[21:19:04]:Initializing LCD module [ OK ]
[21:19:04]:Uncompressing core image files [ OK ]
[21:19:47]:Extracting corefs [ OK ]
[21:19:49]:Enabling watchdog [ OK ]
[21:19:49]:Starting device manager
Performing eUSB Flash fast test... [ DONE ]
[ OK ]
[21:19:51]:Mounting flash [ OK ]
[21:19:51]:Initializing 511MB as swap on zRam0 [ OK ]
[21:19:54]:Turning swap ON on zRAM0 [ OK ]
PoE firmware [ OK ]
[21:20:01]:Checking system inventory [ OK ]
[21:20:01]:Installing ancillary FS [ OK ]
Performing integrity check on ancillary partition 0 [ OK ]
Extracting Webui files../
[21:20:27]:Reboot Cause: User reboot (Intent:cause:register 78:86:50:60)
[21:20:27]:Starting syslog service [ OK ]
[21:20:29]:Deleting the Databases [ OK ]
[21:20:30]:Restoring the database [ OK ]
[21:20:31]:Generating SSH keys [ OK ]
[21:20:32]:Initializing TPM and certificates [ OK ]
[21:21:03]:Checking for configuration upgrade [ OK ]
[21:21:05]:rcS Done(123 sec)
[21:21:05]:Starting OS services [ OK ]
Starting auto provisioning
Registered for NTP Sync
Using port gigabitethernet 0/0/15 for auto provisioning
Initiated DHCP, awaiting DHCP response
Auto-provisioning is in progress. It requires DHCP and Activate servers
Choose one of the following options to override or debug auto-provisioning...
'enable-debug' : Enable auto-provisioning debug logs
'disable-debug' : Disable auto-provisioning debug logs
'mini-setup' : Start mini setup dialog. Provides minimal customizatio n and requires DHCP server
'full-setup' : Start full setup dialog. Provides full customization
'static-activate' : Provides customization for static or PPPOE ip assignme nt. Uses activate for master information
Enter Option (partial string is acceptable):
|