eBay

AZ688-2 Wireless Curing Light

Descriptions:

Wireless LED Curing Light 2000mw/cm² Lamp Test Meter Optical Fiber

Because of the Built-in battery of this product and the strict customs,

Please be more familiar with local customs and the circumstances before buying.

Thanks for your understanding!!!

The new brand high quality of curing light has main advantages of others as follows:

1. Excellent quality with competitive price

2. Quick delivery and best service

3. Service tools for dental and easy to maintain and recharge conveniently

4. Large capacity Li-battery can be used for a long one with full charging.

5. Plenty of fiber rods with very reasonable price on sale for you replacement

6. Composes of high power LED, qualified fiber rod.

7. Noiseless; No libration; Generate little heat when working.

8. Imported high power LED and four chips inside.

1. Blue-ray output wavelength:430-485nm.

2. Gradually bright, shiny,bright-wide, the work of three models to choose.

3. Three gear output timing:5s 10s 15s 20s 25s 30s 35s 40s

4. Blue-ray illumination: 5W≥18

5.The effect of curing time: 6s: 2-3mm.

6. Reliable structure and easy operation.

Technical Specifications:

Wavelength: 380-515nm2

Power density: 99-999mw/cm

Only for light probe with a circular emission window: 08-12mm

Measuring accuracy: +/-20%

Adjustable light intensity: 2000mw/cm2

Operating conditions:

Temperature :+10℃to +40℃

Relative humidity: 30% to 75%

Ambient pressure: 700hpa to 1060hpa

Technical parameters:

Output power-----------5w

Size ----------------------diameter 270*208*118mm

Weight-------------------720g

Working voltage--------100-240V AC, 50-60HZ

Packing List:

Main engine of light-curing Device------1 set

Optical Fiber--------------------------------1 piece

Battery----------------------------------------1 piece

Battery Charge Seat-------------------------1 set

Shade Board ---------------------------------1 piece

Instruction Booklet -------------------------1 piece

YS-C Curing Light

Features

NAME：LED curing light

MODEl：YS-C

This high power 2700mw/c㎡ LED Curing Light has a humanity intelligent chip with a high intensity

LED light and Li-on rechargeable battery.

This device can cure all the dental resin known in the market nowadays; with a performance level far

superior than the halogen curing light's, it has 3 different working modes and it can solidify 4-5mm

deepness in a few seconds.

Benefits：

1)Very convenient to operate.

2)Small size,cordless and light weighted.

3)No dazzling strong light which allows you to aim the light to the exact position and improve the effectiveness of the treatment.

4)No vibration.

5)Noiseless operation.

6)High power rechargeable battery.

7)High powerful light intensity with a maximum reach of 2700MW/cm2.

8)3 different working time modes,exposure time for optional curing:8s/6s/4s.

9) You can select the correct mode according to the different types of material you wish to cure,their speed of reaction,and the clinical protocol you are following.

Best Quality Materials:

* Mono-fibered glass light guides for various applications.

* Anodized aluminum handpiece.

* Latest generation of CMS electronics.

* Very high-quality single L.E.D.

* Li-lon battery with no memory effect

Design and Ergonomics:

* Silent and hygienic, no fan.

* Round surfaces allow for easy and comfortable manipulation.

* Compact, lightweight and well-balanced light guide rotates through 360°.

* Base-charger can be turned in all directions and low battery warning.

* Can be used anywhere in the world. The voltage input is 110V-240V and we will provide you

with the correct according to the shipping destination.

Specifications:

- Blue Light Intensity: 2700mw/c㎡

- Rechargeable Li-ion battery

- Spectrum Range: 420nm- 480nm

- Power : AC110-230V / 50-60Hz

- Time option:8s/6s/4s

- Weight: 0.65kg

-Full Metal shell

Package Includes:

1 LED Curing Light Device

1 High Capacity Rechargeable Battery

1 Charger

1 Charger Socket

X2 Curing Light

Feature:

Technical Parameters:

Light Source:Broad Band LED;

Wavelength Range:385 - 515 nm;

Light Intensity:> 2300mW / cm²;

Battery:Lithium-ion battery (total running time when the battery is fully charged: at least 80 minutes);

Power Input Power:AC 100-240V 50 / 60Hz;

Charging time: about 45 minutes;

Size:Handle:Φ20 mm × 240 mm; Charging stand: Φ63 mm × 30 mm (all of the above are the largest size)

Weight: Handle: 96 grams; Charging seat: 99 grams;

Operating ambient temperature: + 10℃ - + 40℃(+ 50 °F - + 70°F);

Operating relative humidity: 30% - 75%;

Operating environment pressure:700hPa - 1060hPa;

Package Contents:

1 × host handle;

1 × charging base;

1 × power ;

1 × user manual.

Operation and function description:

The entire handle is only one button, light built-in button.

1. For the first time, charge the light curing handle first. the USB cable of the charger into the USB port of the power ,the power into the power socket, and finally

Put the handle on the charging stand; or, insert the USB cable of the charging stand into the USB port of the computer, and then put the handle on the charging stand. Charging instructions are as follows:

| Emerald Flashing | Battery charging;

| Emerald green light | battery fully charged; handle removed the charging seat, the restoration of the previous working mode.

2. Working mode selection, by pressing the button for 2 seconds to release to switch the working mode.

| Blinking Blue | Progressive mode, working time 10 seconds, light intensity 0-5 seconds from 0-1200mW / cm², 5-10 seconds 1200mW / cm².

| Solid blue | Fast mode, working time 3 seconds, light intensity 2300mW / cm ²

3. Turn the light curing lamp on and off, press the button briefly.

4. Switch machine, in standby mode, press the button a short time to open the instrument; stop any operation for 60 seconds, into the ultra-low power standby.

WOODPECKER F*LEDCuring Light

Feature:

Wireless

Long standby time

Working more efficiently

Function Keys:

ON/OFF button：

Turn on or turn off the LED blue-ray output

Can make the machine run

Time setting: 5s, 10s, 15s, 20s,25s,30s,35s,40s

Technical:

Charger input:110V-240VAC 50-60Hz

The charger output:DC4.2V 1A

Lithium battery voltage:DC3.7V

Lithium battery capacity:1500mAh

Output optical wavelength:420-480nm

Output light intensity:1200-1400mw/cm2

1set Package:

1 X Curing light

1 X High capacitance rechargeable battery

1 X Charger

1 X Charger socket

Cv -gun 1 Second Cure Curing Light

Descriptions:

Introduction:

1.Technical specifications：

1.1Dimensions: 25mm×25mm×240mm

1.2 Net weight: 280g

1.3 Power source

1.3.1 Power supply: rechargeable Lithium battery

1.3.2 Battery mode: ICR 18490

1.3.3 Battery voltage and capacity: 3.7V/ 1400mAh,Battery has protection against Over-voltage, over-current and short circuit.

1.3.4 Power Input: 100V to 240V, 50Hz/60 Hz Input Power: 10VA Power Output: DC5V/1A

1.4 Light source:

1.4.1 5W high power blue light LED

1.4.2 Checking method: the LED light is fine when the light is on during operating correctly.

1.4.3 The wave length of this product can match with the clinical dental resin solidification, such as 3M, Dentspl etc.

1.4.4 Wave length: 385nm-515nm

1.5 Light intensity: 1000 mW/c㎡~2300mW/c㎡

2. Operation：

2.1 Press the mode button. Following two modes are available.

2.1.1 TURBO Mode: screen shows P1, Press the time button to select of time which could be 1 and 3 seconds.Its output light intensity is about 1800 mW/c㎡-2300mW/cm2

2.1.2 NORMAL Mode: screen shows P2, Press the time button to select of time which could be 5,10 ,15and 20 seconds.Its output light intensity is about 1000 mW/c㎡-1200 mW/c㎡

2.2 During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, press the ON/OFF button and the main unit will produce "Bi" sound, the curing light radiates blue light and starts working according to the set modes. Meanwhile, it starts counting down and will produce tone at every 5 seconds, it stops working when counting down to "0".

2.3 During operation, the blue light can be stopped by press the power button at any time.

2.4 After a working cycle, operator can press the ON/OFF switch to start another working cycle. Stop operating if the equipment began to heat obviously, do not restart until the equipment cool down. Suggest continues working cycle less than 10 times.

2.5 Low power detective circuit is fixed inside of the main unit, when low power is detected, the display screen of main unit will wink, please charge in time.

2.6 When the battery needs to be charged, connect the of the into the AC100V~240V power supply. Then connect the output of the to the DC 5.0V input of the pedestal, and then the logo turn to blue. Put the main unit to the charging point of the pedestal, the display screen turn to scrolling display, and the curing lights starts charging.

2.7 After operating, take off the disposable sleeve and throw away, forbidden to reuse.

2.8 This equipment will turn off automatically if don't any action within 2 minutes, turn it on by press any button.

2.9 The depth of solidification of composite is no less than 2mm per 1 second.

LED plus105 1 Second Curing

INSTALLATION:
• Insert light head into the curing light handpiece with a twisting motion，Ensure that both the direct light source head and the light curing host are fully connected to their corresponding positions
• Connect the adapter connector to the USB Type-C charging line, and then connect the power supply. The magnet tail cap at the bottom of the host can be stably adsorbed on other metal surfaces.
• After switching on the power adapter, insert the charging port or pull out the charging port, the machine will wake up automatically, and the host screen will light up
• The main panel indicator light "orange" indicates that the battery is in charge, and the light "green" indicates that the battery is full, and the machine will automatically stop charging.
• When the host is charged for one minute in an unused state, the screen will shut down automatically, and the battery will still be charged until the battery is full
• The battery is not fully charged prior to shipment. Please charge the battery for a minimum of 4 hours prior to first use
• To check the battery, press and hold the time switch for 4 seconds, display screen will show:
a.) 4.2 – 3.7- Battery is normal
b.) Lo- Battery is low
• When battery is low, curing light circuit will automatically compensate for power output or turn the light off. Always recharge the curing light when the battery is low Lo
• Direct charging option from transformer for easy transportation and mobility

OPERATION:
• Turn on the curing light with on/off switch
• his machine has 1S high power. 3S high power. full RAMP PULSE 3'+3'+6'+6'seven working modes. The default mode is (full power) and the default time is 10 seconds.
• Press and hold the time button for 0.1 seconds to select the time.Only three time modes of FULL RAMP PULSE can be selected, which are 05 10 15 20 25, respectively.
• Long press mode button 0.5 seconds to unlock, mode selection can be made, when no operation 30S automatically unlock, and long press mode button 0.5 seconds to unlock.
• Every change of time or mode, there will be a ‘beep’ sound. The curing light will keep the last program selected in memory
• Put on the disposable curing light sleeve to cover the whole curing light for cross-infection control. Then put on the light protective shield and light head protective ring, the curing light is ready for use
• Remove and dispose of the curing light sleeves after every patient
• Curing light will automatically turn off if not in use for 1 minute

SPECIFICATION:
Power supply:Input: AC 100-240V, 50/60Hz
Output :DC 5V/1A
Intensity High: 2500 mw/cm²
Battery: 3.6V, 2600 mAh (9.36Wh)
Handpiece dimension: Φ3.0 cm x 24 cm

Packing List:
Main unit of the LED x1
Protective light shield x1
Transformer (100 -240V) x1
USB Type-C Chrging line x1
Instruction manual x1

LED PRO105 1 Second Curing

INSTALLATION:
• Insert light head into the curing light handpiece with a twisting motion，Ensure that both the direct light source head and the light curing host are fully connected to their corresponding positions
• Connect the adapter connector to the USB Type-C charging line, and then connect the power supply. The magnet tail cap at the bottom of the host can be stably adsorbed on other metal surfaces.
• After switching on the power adapter, insert the charging port or pull out the charging port, the machine will wake up automatically, and the host screen will light up
• The main panel indicator light "orange" indicates that the battery is in charge, and the light "green" indicates that the battery is full, and the machine will automatically stop charging.
• When the host is charged for one minute in an unused state, the screen will shut down automatically, and the battery will still be charged until the battery is full。
• The battery is not fully charged prior to shipment. Please charge the battery for a minimum of 4 hours prior to first use。
• To check the battery, press and hold the time switch for 4 seconds, display screen will show:
a.) 4.2 – 3.7- Battery is normal
b.) Lo- Battery is low
• When battery is low, curing light circuit will automatically compensate for power output or turn the light off. Always recharge the curing light when the battery is low Lo
• Direct charging option from transformer for easy transportation and mobility
OPERATION:
• Turn on the curing light with on/off switch
• his machine has 3S high power. full RAMP PULSE 3'+3'Five working modes. The default mode is (full power) and the default time is 10 seconds.
• Press and hold the time button for 0.1 seconds to select the time.Only three time modes of FULL RAMP PULSE can be selected, which are 05 10 15 20 25, respectively.
• Long press mode button 0.5 seconds to unlock, mode selection can be made, when no operation 30S automatically unlock, and long press mode button 0.5 seconds to unlock.
• Every change of time or mode, there will be a ‘beep’ sound. The curing light will keep the last program selected in memory
• Put on the disposable curing light sleeve to cover the whole curing light for cross-infection control. Then put on the light protective shield and light head protective ring, the curing light is ready for use
• Remove and dispose of the curing light sleeves after every patient
• Curing light will automatically turn off if not in use for 1 minute

SPECIFICATION:
Power supply:Input: AC 100-240V, 50/60Hz
Output :DC 5V/1A
Intensity High:1800mw/cm2
Battery: 3.6V, 2600 mAh (9.36Wh)
Handpiece dimension: Φ3.0 cm x 24 cm .

Packing List:
Main unit of the LED x1
Protective light shield x1
Transformer (100 -240V) x1
USB Type-C Chrging line x1
Instruction manual x1

FDA Statement

The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies. If so, you can bid on this item only if you are an authorized purchaser. If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.

Seller's name: 2013eshop01
City: Shenzhen State: Gunagdong.China
Telephone number:0755-83162399