Item Type: Air Pressure Mattress
Material: PVC
Voltage: 220V
Continuous Working Time: More than 24 hours
Air Cushion Bearing: 135kg / 297.6lb(approx.)
Function: Waves, with sleep function, no defecation hole

Installation and use method:
1. The supplied charging pump is connected with the mattress to ensure 24-hour automatic inflating.
2. Will prevent bedsore gas mattress on the bed or single bed (bed surface can not have incisive or strong items, to prevent air mattress damage), so that the air mattress inlet position is located in the patient's foot, the air tube side up, cover the sheet, can also cover a pure cotton thin mattress, only single sleep.

3. The air pump can be removed from the box and placed on the table or under the bed according to the situation. 20cm from the ground to a firm position, flat in a dry and clean place, or fixed on the end of the bed or the patient's feet by hook, so as to avoid the impact of the field sound on the patient, please handle with care, pay attention to moisture and dust.
4. Connect the power supply:
1) The air mattress strip is leveled up, tighten back two white clip, connect the power supply, after open the power switch, then put the cushion on the quick joint connection inflator pump, inflatable (for angle turn "model), air cushion can be filled up after about 13min, can make patients lay on the mattress, if you want to use waves function, the yellow switch on the air pump switch down: The yellow light is not on. If the air cushion is full of air, press the yellow switch upward. The yellow light will light up in about 4 minutes as normal
(2) The pump power source into the power socket, and then connect the air pump with the connecting pipe at the mattress air outlet, connected to the power supply, will make the air pump switch is set to ON, and the indicator, start switch, pressure adjusting knob clockwise to open the position and rotation to the maximum pressure, pump the outlet gas discharge, inflatable mattress begin to work.
5. One end of the air pipe in the small packaging bag is connected to the air outlet on the air pump, and the other end is connected to the air inlet mouth of the air mattress. The connection should be firm and in place, so that there can be no air leakage.
6. The air mattress enters the inflating working state. After inflating for 10-20min, the pressure in the air mattress can reaches the normal use state.
(1) about turn over (suitable for JLL-TO4A. JLL-T04B,JLL-T04C,JLL-TO6A,JLLTO6B, JLL-TO6D) :Loose the clip and push it to the left to turn over, about 15 minutes, the left side automatically rises: if you want to turn over, push it to the right to turn over (the left turn over gas group is automatically discharged). 
Note: someone needs to be on the mattress when turning over.If you want to resume lying flat, after the clip is stuck, if the wrench turns over on the left, push it to the right to turn over, automatic exhaust to restore lying flat.
(2) Backup (for JLL-TO5A. JLL-TOSB, JLL-TOSC, JLL-TO6A. JLLTO6B,JLL-TO6C, JLL-TO6D) : This function can only be used when the air cushion is lying flat;Loosen the clip and push it to the back.After about 30 minutes, the back Angle can 40 degrees. If you want to change from 40 degrees to 30 degrees, 20 degrees or lying flat, the white clip is stuck and pushed to the flat, to the desired Angle, and then pushed to the back, back to lying flat, the clip is stuck to the flat, about 30 minutes later you can lie flat.
7. When defecating and urinating, unfasten the buttons on both sides, pull open the small air cushion at the stool hole, and put it into the bedpan for use; After use, put the small air cushion back to the original position and restore the undulating state (suitable for air mattress with urinal hole).

8. When the patient needs to deflate quickly, the pneumatic pump should be stopped immediately and the airway should be pulled up and down from the pneumatic pump. The airway can be punctured in case of emergency.
9. Turn on the power supply of the air pump, turn on the power switch, the green indicator light on, and set the pressure regulating knob counterclockwise to sleep state. The two air outlets of the air pump discharge gas, and the gas bed stops fluctuating to the static state. The purpose is to enable patients to have a better rest and improve the quality of sleep.

Maintenance method: remove the power plug and cut off the power when moving, maintaining and repairing the product.
1. Maintenance of the air pump: after a period of time (generally three months, depending on the different environment), the filter screen under the casing should be cleaned, the specific steps are as follows:
A) Remove the filter box (filter screen and filter cover) under the air pump together.
B) Rinse the filter with clean water. If the dirt sticks firmly, it can be soaked in running water.
C) After the filter screen is dried, it is loaded back into the filter box and fixed (before the filter screen is cleaned and dried, do not load into the gas pump, otherwise it will affect the normal life of the air pump).
2. Maintenance of the air cushion:

A) Steps: unlock the buckle, pull out the guide pipe, take out the strip air chamber, clean the bottom and air chamber.
B) Cleaning: Clean the surface with a neutral detergent, and then wipe it clean with water.
C) Cleaning: the sheets or bedspreads used by infectious patients shall be washed with a laundry solution containing 500mg/ chlorine dioxide for more than 30min, and then rinsed with clear water and dried for later use. Drugs can also be used for cleaning.
D) Put the air cushion in a dry and ventilated place and pay attention to moisture . Avoid prolonged exposure to sunlight to slow down the aging rate of air cushion.