Product Description

• NEW UPGRADE FNCTION : Own our Seesii 3GHz Vector Network Analyzer,you can test the standing wave impedance of the antenna, you can also debug the duplexer, the insertion loss of the filter, the isolation, the standing wave, you can also test the attenuation of the cable, shorten the coefficient, the phase, you can also test the amplification of the antenna amplifier
• POWERFUL FREQUENCY METER: The improved frequency measurement can measure the antenna frequency of 2.4G up to to 3G. 70dB(50KHz-1.5GHz), 60dB(1.5GHz-3GHz). Reflection Measure S11: 50dB(50KHz-1.5GHz), 40dB(1.5GHz-3GHz); Antenna Analyzer: 1.005(50KHz - 1.5GHz), 1.02(1.5GHz-3GHz)
• IMPROVED ACCURACY: NanoVNA SAA-V2 Vector Antenna analyzer equipped with the upgraded shell,Strong anti-interference, improve accuracy.with 3.2 inch touch screen and touchscreen pen,make more accurate and easy to operate.
• POWERFUL SECURE POWER SUPPLY: This SAA-V2 is battery powered or USB powered; Built in 2000mA-h battery, could work for about 3 hours continuously, if need extra working time, it can be connected to power bank or power source.
• COMPATIBLE :The 3GHz second-generation NanoVNA vector network analyzer is based on OwOComm's S-A-A-2 design, and its performance is greatly upgraded.Can be control by PC,computer software compatible with Linux, Windows (7+)

SEESII Nanovna 10kHz-3GHz Vector Network Analyzer With Metal Case

Measuring frequency range: 10kHz-3GHz

System dynamic range (after calibration): 70dB (50k to 1.5GHz); 60dB (to 3GHz)

S11 noise floor (after calibration): -50dB (to 1.5GHz); -40dB (to 3GHz)

Scan rate: 100 points/second

Number of scanning points (on device screen): adjustable, maximum 201 points

Number of calibration points (maximum number of USB scanning points): 1024 points (when connected to a computer and using a host computer)

Power supply: USB, 400mA RF port: SMA (not RP-SMA)

USB interface: Micro USB

Display screen: 3.2 inch TFT (320 x 480)

Battery: 2000 mA-h 3.6V/3.7V battery, 6*40*60 mm (maximum size)

Net weight: 320g

Port 2 return loss: >= 13dB (to 3GHz), 20dB (to 1.5GHz)

Display tracking: 4, mark: 4, save settings: 5

Computer software compatible: Linux, Windows (7+)

S-A-A-2 Upgraded Version

The 3GHz second-generation NanoVNA vector network analyzer is based on OwOComm's S-A-A-2 design, and its performance is greatly upgraded.

Compared with the basic version S-A-A-2, SAA-V2 has designed a metal case, and the screen size has been increased from 2.8 inches to 3.2 inches, and a touch screen pen has been added to make your operation more convenient, while adding the function of measuring the duplexer and the filter.

 

3.2 inch Touch Screen 3.2 inch Large touch screen is more precise and easy to operate (touch screen pen is incuded )	2000mA-h USB Rechargeable Built-in 2000mA-h battery rechargeable,no need to connect power supply	Metal Shell Case with the metal shel,strong anti-interference, improve accuracy Ples Note:Must recalibrate or call back the calibration data after each startup and frequency change

 

Improved Frequency Measurement SAA-V2 can measure the antenna of 2.4G in addition to 3G, and it can also measure the duplexer and the filter (at present, except for this version, other model can not do such a powerful function)	VNA Software Control NanoVNA Saver This software connects to a NanoVNA and extracts the data for display on a computer, and for saving to Touchstore files Software compatible with Linux, Windows (7+) OS	Mini Compact & Powerful This Antenna Analyzer is a DIY product that provides perfect vector network measurement capabilities,it can also measure the duplexer and the filter,tiny and handheld

 

 

 

Filter Attenuator,Seesii RF Demo Kit NanoVNA RF Tester Board Filter Attenuator for NanoVNA-F NanoVNA-H Vector Network Analyzer Kits

 

About this item

• Made of fine quality material, practical, has a long service life.
• Compact and lightweight, easy to operate and use.
• Can be used with NanoVNA-F to measure 6.5M ceramic notch filter.
• Can be used with NanoVNA-F to measure homemade low-pass-filter, 3dB bandwidth about 400MHz.
• This is a vector network analyzer learner tool. Package Included 1x PCB RF tester board, 2 x 20cm adapter cables

---

---

Seesii RF Demo Kit NanoVNA RF Tester Board Filter Attenuator for NanoVNA-F NanoVNA-H or Other Vector Network Analyzer

Specifications: Material: PCB RLC series and parallel circuit 1 RLC series and parallel circuit 2 33 ohm resistance, SWR=1.5 75 ohm resistance, SWR=1.5 BSF ceramic notch filter, center frequency 6.5MHz BPF ceramic filter, centre frequency 10.7MHz RC series circuit LC series circuit Capacitor Inductance Homemade low-pass filter, 3dB bandwidth 400MHz Homemade high-pass filter, 3dB bandwidth 500MHz Short-circuit calibration circuit Open-circuit calibration circuit 50 ohm load calibration circuit Straight-through 10dB attenuation circuit 3dB attenuation circuit Each set of functional circuits Item size: 100 * 100mm / 3.9 * 3.9in Item weight: 38g / 1.3ounce

Package list: 1 * PCB RF Tester Board 2 * 200mm Adapter Cable

---

NanoVNA Vector Network Analyzer Testboard Kit for NanoVNA NanoVNA-F NanoVNA-H NanoVNA-H4 Network Analysis Test Board Demo Board

 

About this item

• This test board contains a plug-in test circuit suitable for VNWA Testboard, and a set of 0805 and 1206 patch test circuits are added.
• Suitable Model: This test board kit is used for NanoVNA NanoVNA-H NanoVNA-H4 NanoVNA-F series vector network analyzer user-friendly measurement plug-ins and SMT devices.(if you want the series of NanoVNA ,ples welcome to our store)
• DIY kit,stable performance, high accuracy, high sensitivity.Made of fine quality material, has a long service life.
• What you can get: The package includes Testboard x1, 6X SMA Female Adapter , 4x 6mm Copper Stud, 4x M2.5 Screw , 2x 40pin Round Socket ,2x 0805 49R9 Calibration Resistance.
• Please Note: Due to the SMT circuit cannot fully consider all kinds of test situations, some parts of the test may need to be cut over. Please ensure that you have sufficient hands-on capabilities.

Product Description

NanoVNA Vector Network Analyzer Testboard Kit

DIY kit, need to have welding ability; Need to burn-firmware, SMD electronic components have been soldered, KIT of ATU (Automatic Antenna Tuner) developed by N7DDC All information about project you can find on GitHub (N7DDC).

Package Included

• 1X PCB for ATU-100 7x7 HF autotuner
• 6X T68-2
• 1X BN43-202
• 1X PIC16F1938 (1pcs) soldered on PCB with default firmware v3.0
• 100R 2512 1% (4pcs).
• 15X relay HK4100F-DC12V

Specification:

Power supply range: 10 - 15 VDC

Max current : 450mA

Max working power: 100 watts

Max measured power: 150 watts

Minimum power for tuning start: 1 watt

Recommended maximum power while tuning not above 30 watts. (after tuning you can set 100 watts and work on this power)

Minimum measured power: 0.1 watt

Step for measurement on powers under 10 watts: 0.1w

Step for measurement on powers above 10 watts:1 w

Power measurement accuracy : 10%

Maximum inductance set: 8.5 uH

Minimal step for setting inductance: 0.1 uH

Maximum installed capacity: 1870 pF

Minimal step for setting capacity: 10 pF

100 Watts tuner, 7x7 (7 capacitors x 7 coils) based on PIC 16F1938.

---

	NanoVNA Testboard Kit	Filter Attenuator	NanoVNA	NanoVNA-F V2	LibreVNA
Frequency Range	-	-	10KHz-1.5Ghz	50kHz-3000MHz	100kHz-6GHz
Touch screen	-	-	2.8-inch	4.3-inch	-
Power Supply	-	-	650 mAh	5000 mAh	5000 mAh