Description:

1.  100% brand new and high-quality products.

2.  Made of high-quality materials, durable and practical.

3.  The temperature difference of the machine can be calibrated according to the measured temperature, so that the temperature is more accurate and the shell rate is higher.

4.  Double power supply, not afraid of power failure.

5.  Bionic incubation, inspired by the structure and function of the organism, the bionic water bed designed according to the incubation conditions of the mother can easily hatch every egg.

6.  Accurate temperature control, self-contained photo eggs, not afraid of power outages, low energy consumption

Parameter:

Product voltage: AC110V-220V/DC12V

Power: 20W

Size: 36*24*19cm

Plug: American plug

Scope of application: all kinds of poultry eggs

Assembly instructions

1.  The foam box is above 50 cm from the ground to avoid the ground temperature affecting the machine temperature.

2 Place the heating pad at the bottom of the box.  【Plastic water bed: Put the plastic mesh on

Bottom of machine, heating pad on top of mesh 】

3.  Put the two water bags together and add a little more than 1/3 of the cool water (note: be sure to add cool water, warm or hot water will make the machine overwarm) After adding the water, put the temperature probe directly into the water bag and contact with the water.  The water bag is placed horizontally into the machine to squeeze out excess air and smooth the water bag.

4.  Roll the mouth of the water bag and fix it on the side of the machine with a metal clip.  [Plastic water bed: Clamp the metal clip directly on the water bag]

5.  Cover the thermal insulation cotton, set the temperature, the machine will display the current internal temperature, need to wait for the machine to heat up, after reaching the set temperature, the heating lamp will be off.  (L)

The warming process will take a few hours, please be patient)

6.  When the temperature rises to about 20 degrees, the eggs can be placed.  The eggs must be placed on the water bag, and the thermal insulation cotton cover the eggs to start hatching.  [Plastic water bed: After covering the thermal insulation cotton, it is also necessary to cover the machine cover;  foam water bed: directly cover the thermal insulation cotton, the foam cover is to protect the box during transportation, and it is not used during incubation] Note: the heating pad is strictly prohibited to dry burn without water and electricity!!!

Incubation steps:

The following is an example of eggs to explain the incubation method:

The first step: egg selection

3-7 days of birth of fertilized eggs (the best), no feces, no cracks, no broken egg contamination, after the test machine is completed, the seed eggs lie flat into the incubator to incubate (the date of laying eggs can be marked on the egg with a pen)

Step 2: Heat and turn the eggs

The whole incubation period can be incubated at the default temperature of 37.8 (constant temperature), no need to adjust the temperature;  Turn the eggs 3-4 times a day, and do not turn them at night.  Each time after turning, spray the eggs with warm water to maintain humidity.  The spray bottle can be put into the machine to keep warm.

Step 3: Light the egg

About 7 days of incubation to view the development of eggs, in the dark environment by pressing the panel of the "egg" button, with the egg light at the big head of the egg one by one can clearly see that there is spider blood is a good fertilization of eggs, otherwise it is no sperm eggs are incubated, need to be screened out;  After 14 days or so, choose the weak egg with uneven blood.

Step 4: Dry the eggs

Incubate until about 14 days, you need to open the thermal pad to air the eggs every day.  According to the ambient temperature to determine the drying time, the ambient temperature can be hung for about 5 minutes, the ambient temperature is low, 2-3 minutes can be hung.

Step 5: Set the plate

The last 3 days of the shell period do not need to turn the egg, at this time must pay attention to spray more warm water, not less than 6-8 times a day, you can add vinegar in warm water to soften the eggshell, which is conducive to the chick's shell;  Have pecking shell must avoid pecking open area spray.

Step 6: Incubation

After breaking the shell, the egg skin is picked out in time, and the small chicken feathers are dried out from the incubator, find a carton covered with straw, hang a heat preservation lamp and slowly detemperature feeding, generally keeping the chicks warm for 7-10 days, the detemperature temperature is about 30 degrees (can be adjusted according to the environmental temperature).

Frequently asked Questions

1. Just turn on the alarm

The newly energized machine will emit a "drip drip" alarm sound during the heating process, and the display screen will display "L"; This is because the temperature has not risen to the set value just after the boot, the temperature probe monitors the low temperature in the machine, and the alarm prompts, press the minus key to cancel the alarm, and the temperature will rise normally.

2. The temperature of the machine is unstable and overtemperature

During the incubation process, because the temperature probe monitors the real-time temperature inside the machine, the display temperature fluctuates up and down, which is a normal phenomenon and there is no need to worry. If the machine overtemperature occurs during use, the machine alarm displays "H" and continues to heat up; You can first press the minus key to cancel the alarm, pour out more than half of the water in the water bag, add cold water to the whole water bag, add a little more than 1/3, put the temperature probe directly in the water bag to contact the water, observe the temperature is normal, the probe has been incubated in the water bag.

3. The machine is not powered during incubation

If the screen is not displayed and the power indicator is off, check whether the power cable is firmly inserted, or replace the power adapter and check whether the display is normal.

4. Instructions for power failure

Double electric version: you can use the battery line to connect the 12V60 a or more battery, red to the positive electrode and black to the negative electrode, please do not connect wrong, the battery is prepared; Unplug the power supply in time to avoid voltage instability affecting the machine. Single electric version: after power failure can raise the room temperature, with quilt or old clothes wrapped machine heat preservation; Or temporarily keep the eggs warm by constantly changing the water bag with warm water.

5. Before each incubation or no operation, the machine debugging error is abnormal, and the factory Settings need to be restored.

Restore factory method: "+" "-" together hold for eight seconds, the display digital display 888, let go.

6. Base temperature

Change: When the temperature needs to be set for hatching other eggs, press the setting key, and when 37.8 blinks, press the "+" key or press the "-" key to debug and set the temperature value, and save it automatically for 10 seconds.

Matters needing attention

1, there will be a short period of temperature instability after the operation of the machine, and then observe whether the temperature is normal after the temperature is stable. Do not open the thermal insulation cotton without special circumstances during the incubation process, and do not power off for a long time to avoid affecting the development of eggs.

2, the machine will not operate or need to carry out product maintenance, replacement parts, you can consult the store customer service to answer and deal with to ensure faster solution to the problem.

3, due to the different ambient temperature and humidity, the machine use method and incubation process is only for beginners' reference, and those with incubation experience can operate according to their own experience.

Package include：
1 x Water bag
1 x Temperature probe
1 x Thermal insulation cotton
1 x Spray bottle
1 x Metal clip
1 xBattery cable
1 x adapter