UK's Favourite FRICTION REDUCING OIL ADDITIVE - AMETECH METAL-TEC10 Treatment 

This listing is for 500ml of Metal-Tec10 which will treat approximately 10 litres of oil as an additive.

500ml of Metal-Tec10™ will treat approximately 10 litres of oil (at 5% ratio) as an additive for engines (petrol, diesel and hybrids), governors, automatic and manual transmissions, standard differentials, limited slip differentials, overdrive units, marine gearboxes, transfer boxes, power steering units, locomotive engine governors (Woodward), hydraulic spool valves and forklift hydraulic systems, plus many more automotive and industrial areas of application.

For automotive or industrial use, add Metal-Tec10™ at the rate of 5% by volume to any oil or grease to reduce friction, heat and wear and increase efficiency. Metal-Tec10™ flattens metal surfaces to increase lubrication and reduce drag (friction). There are many other oil additives on the market that act in a similar way but, unlike the others Metal-Tec10™ contains no chlorinated solvents and is PH neutral, protecting the metal surfaces against acid erosion which occurs when short-chain chlorinated hydrocarbons mix with water droplets and moisture to form hydrochloric acid. Metal-Tec10™ contains no PTFE, silicone, graphite, moly or solid lubricants and is neither acidic nor alkaline, just pure petrochemical halide blending.

Customer Reviews:

Here is a review from an eBay customer who purchased Metal-Tec10™ from us in 2010 and has since been back for more:

Reviewer: Paul Gascoyne from Sheffield
This stuff really works. I own a Jeep Grand Cherokee Orvis, I had a power steering line come loose and the fluid drained out. I have an illness that makes it difficult for me to walk so I drove the car home. I repaired the leak and refilled the system with the best power steering oil I could get for the car, bled the system and took it out for a run. The steering was notchy and rough, it also was very slow on returning to centre. I ordered one of these additives and when it arrived I drained out some of the oil and added the whole bottle. I must admit I added 25ml more than I should have - I put the whole bottle in. Well after only a couple of hundred miles the steering is transformed. It has lost the notchy feel, goes where I put it and is just - well nice to drive, better than it was before the oil drained out to be honest. I have also noted that it keeps getting a little better as the miles add up. By the time I get to the 1k marker I will probably need surgery to remove my smile. It has saved me two days hard work and God knows what in money. If your system will not respond to this stuff then it's beyond help. My thanks to the team. I will be back for other additives. Paul

Reviewer: Tony Bellamy, Cheltenham
2 words needed: brilliant and amazing. Used this for over eight years now and in so many applications. Now I just take the view that if there is either oil or grease needed, then it would be very limited without MT10. This gives me insurance and assurance that whatever will not wear out, produce less friction less heat and last for as long as needed. This has saved many thousands in repairs, replacement and maintenance over the years. Many receive advice, only the wise profit from it. Remarkable stuff.

Ametech Metal-Tec10™ is an advanced technology, anti-friction lubricant additive, consisting of a blend of the highest quality petrochemical products. It is a PH neutral maximum duty, metal conditioning formula especially recommended for use in lubrication systems where there is a special concern for extra protection due to extreme pressure, friction-related heat and high-wear conditions. Metal-Tec10 contains no chlorinated solvents, PTFE, silicone, graphite, moly or solid lubricants. Metal-Tec10’s formula allows it to blend well with all types of petroleum and most synthetic lubricants (but not vegetable oils or esters), enhancing the performance of both.

Ametech Metal-Tec10 can be used in conjunction with AMETECH ENGINE RESTORE OIL providing it is added after the RESTORE oil has been in the engine for 1000 miles. Metal-Tec10 has been formulated to increase the efficiency and performance of your automobile, truck or commercial vehicle. But in order to obtain the full benefit of the product, it requires dedicated interest on your part to follow product directions and take proper care of your vehicle. Oil changes, oil filters, gas filters, good grades of fuel, proper lube jobs, tune ups and qualified auto technicians performing maintenance and repairs all pay dividends toward the annual expense and the life of your vehicle.

Ametech Metal-Tec10™ Metal Treatment is recommended for these automotive applications:

• Engines. Nothing protects better at start-up!
• Transmissions (Automatic & Standard)
• Power Steering/Rack Assembly Units
• Differentials
• Recommended for gasoline & diesel engines

Advantages

• Smooths, seals & protects metal surfaces of bearings, pistons, cam, crankshaft, lifters & all other internal, moving metal parts
• Protects engine against friction-related heat & wear
• Free governors and eliminates governor hang-ups
• Reduces operating temperatures
• Increases horsepower
• Extends the life of lubricated engine parts
• Reduces oil consumption
• Recommended for petrol & diesel engines.

One of the biggest enemies of a transmission is heat. The amount of heat present in the system will normally dictate the lifetime of that transmission. When Ametech Metal-Tec10 is added, heat is significantly reduced. Metal-Tec10 addresses the extreme-pressure (EP) areas, such as planetary and worm gear systems, along with bushings, bearings and shafts.

VALVE BODY OPERATION: In many cases presented by professional transmission builders, Metal-Tec10 has freed the valve body and maximized performance with no recurrence of sticking or intermittent hang-ups.

GOVERNORS: As most transmission builders are aware, there are certain governor systems that have unique tendencies to hang up for no apparent reason. Two reasons these hang-ups occur are contaminants and microscopic spiking of the metal due to electrolytic corrosion of the metal. Ametech Metal-Tec10 will displace contaminants and smooth and seal metal surfaces, removing electrolytic spikes and preventing their formation.

Advantages

• Reduces heat
• Frees valve bodies for maximum performance
• Free governors and eliminates governor hang-ups
• Keeps oil passageways, orifices and ball checks clean and fully operational
• Extends the service life of the transmission
• Eliminate premature failure and costly call-backs
• Reduces wear & metal particle fallout & debris
• Removes varnish buildup
• Eliminates lock-up chatter in the torque converter
• Insures proper shift
• Does not affect seals & gaskets
• No negative affect on sprag or clutch friction*
• Recommended for automatic & standard transmissions
• Contains no PTFE, graphite, silicone or moly.

* Although Metal Tec10 reduces friction, it has no negative affect on the sprag or clutch friction necessary for the operation of the transmission. As confirmed by Raymark in a letter of October 1986 in testing their SAE clutch pack: "The results of our test indicate no change in the friction levels, thus we do not expect the addition of your additive to have a negative effect on our friction products."

IMPORTANT: Metal-Tec10 should not be used in CVT gearboxes. CVT (Constant Variable Transmission) oil or fluid improves the friction/grip between rubber/metallic belts and alloy/composite pulleys, whereas Metal-Tec10 reduces friction between metal-on-metal components, spool valves & spindles lubricated by ATF (automatic transmission fluid) in automatic transmissions. As these requirements are opposed, neither ATF nor Metal-Tec10 should be used in CVT rubber/metal belt transmissions.

Advantages

• Protects against friction-related heat & wear
• Smooths, seals & protects metal surfaces
• Reconditions rack piston & cylinders
• Helps return smooth & easy operation to the unit*

*If you are experiencing difficulty with the unit, we recommend the unit be thoroughly flushed prior to the addition of Metal-Tec10.

Advantages

• Treats the metal surfaces of the gears
• Protects against friction-related heat & wear
• Optimizes performance for more power
• Extends the life of lubricated differential parts.

NOTE: Limited slip additive is still required with the use of Metal-Tec10.

• Gears
• Bearings
• Engines
• Heavy equipment
• Gear couplings
• Pumps
• Transmissions
• Hydraulic systems
• Electric motors
• Gear reducers
• Heavy machinery
• Lubrication systems requiring extra protection from extreme pressure, friction-related heat & high-wear conditions.

Carried to the moving metal parts by the fluid to which it is added, Ametech Metal-Tec10™ creates a boundary film which smoothes and seals metal surfaces to reduce friction and friction-related heat. This results in less wear and smoother operation of the mechanism with no danger of build up or changes in tolerances. The end result is improved operation of the system.

Ametech Metal-Tec10 improves the overall tribological properties of the metal surfaces. Film strength is a function of surface roughness and viscosity. The smoother the surface, the higher the film strength, while viscosity can be lower to improve fluid flow conditions.

Ametech Metal-Tec10 treated surfaces will increase fluid film strength, reducing friction, heat, wear and energy consumption. This returns efficiency and previously wasted energy back to the system for increased power. This process, combined with the physical surface improvement of the metals, steps up oil flow, reduces metal film strength, improves the shear strength of the base lubricant, and results in an overall reduction in friction and friction-related wear.

"Wear testing has been completed on your six samples using ASTM method D2783-88, Measurement of Extreme-Pressure Properties of Lubricating Fluids (Four-Ball Method). The test method is used to differentiate between lubricating fluids having low, medium, and high levels of extreme-pressure properties. Three steel balls are clamped together and covered with the lubricant to be evaluated. A fourth steel ball is pressed into the cavity formed by the clamped balls for three point contact. The temperature is brought to 18.33 to 35°C, with a rotating speed of 1760±40 rpm, then a series of tests of 10 second duration are made at increasing loads until welding occurs.

Values are obtained for weld point (the load in kilograms at which the rotating balls welds to the three stationary balls, indicating the extreme pressure level of the lubricants-force has been exceeded) and load wear index (load-carrying property of a lubricant – the average of the sum of corrected loads determined for ten applied loads immediately preceding the weld point) for each sample identification. Additional sheets attached show the individual load results for each material.

Test Results

Sample	Load Wear Index	Weld Point Kg
A. T-Plus Teflon	43.7	200
B. Supreme Plus	59.9	250
C. Slick 50	42.5	200
D. STP Engine Treatment	58.5	315
E. QMI Engine Treatment	49.0	250
F. MT-10 Engine Treatment	246.4	>800

Repeatability of the test is such that the difference between successive results obtained by the same operator with the same apparatus under constant operation conditions on identical test material would, in the long run,  in the normal and correct operation of the test method, exceed the following value only in one case in twenty: repeatability = 17% of the mean value. The Muscle product (MT-10 Engine Treatment) did not weld at the highest load the instrument was capable of running, so the load wear index for it is an approximation. It has extreme pressure levels much higher than any of the other samples.” (December 22, 1993)

Sincerely, Karen B. Kohl, Manager, 

Special Projects Petroleum Products Research Dept.,
Automotive Products and Emissions Research Division,
SOUTHWEST RESEARCH INSTITUTE, SAN ANTONIO, TEXAS, USA

Ametech Metal-Tec10™ is extremely concentrated and effective even in small quantities. Add 5% Metal-Tec10 by volume to transmission oil, i.e. 50ml to every 1 litre of oil.

Metal-Tec10 can also be applied directly to parts while rebuilding and can be sprayed in a fine mist directly onto the parts you want it to reach or sprayed onto greases to facilitate blending.

For Hydraulics - Add 25ml Metal-Tec10 to every 1 litre of oil.

One Litre of Ametech Metal-Tec10 will treat approximately 20 litres of oil. This contains 500ml of Ametech Metal-Tec10™ which is sufficient as an additive to 10 litres of oil.

 

UK  Economy delivery covers delivery to most areas of the UK  and is provided in most cases by MyHermes courier service.  This is an estimated 3-5 working day delivery service,  although this is not guaranteed. Where MyHermes does not  service a particular postcode in the UK we will employ an  alternative carrier to ship your parcel.

UK  Standard Delivery (1-2 working days*) and Express Delivery  (Next working Day*) will usually be provided by UKMail  courier service, but occasionally we may use DHL.  Some  postcodes in the UK are classed as remote and Express  Delivery carriers increase their shipping charges  accordingly. The postcodes that carry these higher charges  are shown below:

KW1, KW2,  KW3, KW4, KW5, KW6, KW7, KW8, KW9, KW10, KW11, KW12, KW13,  KW14, KW15, KW16, KW17, PA20, PA21, PA22, PA23, PA24, PA25,  PA26, PA27, PA28, PA29, PA30, PA31, PA32, PA33, PA34, PA35,  PA36, PA37, PA38, PA41, PA42, PA43, PA44, PA45, PA46, PA47,  PA48, PA49, PA60, PA61, PA62, PA63, PA64, PA65, PA66, PA67,  PA68, PA69, PA70, PA71, PA72, PA73, PA74, PA75, PA76, PA77,  PA78, PH4, PH5, PH6, PH7, PH8, PH9, PH10, PH11, PH12, PH13,  PH14, PH15, PH16, PH17, PH18, PH19, PH20, PH21, PH22, PH23,  PH24, PH25, PH26, PH27, PH28, PH29, PH30, PH31, PH32, PH33,  PH34, PH35, PH36, PH37, PH38, PH39, PH40, PH41, PH42, PH43,  PH44, PH49, PH50, BT, HS, ZE, IM, GY, JE, IV1, IV2, IV3,  IV4, IV5, IV6, IV7, IV8, IV9, IV10, IV11, IV12, IV13, IV14,  IV15, IV16, V17, IV18, IV19, IV20, IV21, IV22, IV23, IV24,  IV25, IV26, IV27, IV28, IV30, IV31, IV32, IV36, IV40, IV41,  IV42, IV43, IV44, IV45, IV46, IV47, IV48, IV49, IV51, IV52,  IV53, IV54, IV55, IV56, IV63, KA27, KA28, AB31, AB32, AB33,  AB34, AB35, AB36, AB37, AB38, AB40, AB41, AB42, AB43, AB45,  AB46, AB47, AB48, AB49, AB50, AB51, AB52, AB53, AB54, AB55,  AB56, TR21, TR25, PO30, PO31, PO32, PO33, PO34, PO35, PO36,  PO37, PO38, PO39, PO40, PO41.

The delivery  charges for most UK postcodes are programmed into eBay and a  shipping quote obtained by entering your postcode. However,  some postcodes in Northern Scotland (other than Highlands or  Islands) do not register on the eBay system as remote and  quote only the normal shipping rate for the rest of the UK.  If your delivery address falls within one of the  postcodes above, the shipping charge for Standard Delivery  (1-2 working days*) will be £20 and for Express Delivery  (Next working Day*) will be £30. If you wish to pay the  extra charge to have your item shipping by Standard or  Express Delivery, please contact us prior to purchase so we  can arrange to invoice you accordingly. If you have already  completed your purchase and paid only the normal additional  shipping charge for Standard or Express Delivery for rest of  UK, your parcel will be sent by Economy Delivery and any  over-payment in postage refunded.

*delivery to some remote areas, e.g. Scottish Highlands  & Islands, may take 1-2 days longer.

We are happy  to deliver to most international destinations, but because  some destinations carry remote surcharges, the prices for  delivery on our listings are indications only based on  current non-rural, non-remote prices. We will send you a  message before shipping if the actual shipping cost exceeds  those figures quoted, giving you the option to either pay  any extra charges due or cancel the order. If you would like  a firm quotation for delivery cost prior to purchase, please  email or message us with your Country, Town and Postcode to  enable us to obtain shipping quotes from our  carriers.

ENGINES

TRANSMISSIONS

POWER STEERING/RACK ASSEMBLY UNITS

DIFFERENTIALS

OTHER RECOMMENDED USES

Industrial: