SOMETHING COOL ABOUT BORIDE T2 SHARPENING STONE:
FeedBaсk
from the previous Buyer: leopear_43 (347) US $60.56
BORIDE T2 F220 Sharpening stones 6x1x1/4" for Edge Pro, TSPROF, Ruixin, Kazak. (# 353728080088)
FeedBaсk
from the previous Buyer: birke.joh (403) US $18.33
BORIDET2 F400 Sharpening stones 6x1x1/4" for Edge Pro Sharpeners F400 (# 353728088125)
FeedBaсk
from the previous Buyer: dakswaby (131) US $26.25
BORIDET2 F1000 Sharpening stones 6x1x1/4" for Edge Pro Sharpeners F1000 (#353728090261)
FeedBaсk
from the previous Buyer: dakswaby (131) US $20.69
BORIDET2 F600 Sharpening stones 6x1x1/4" for Edge Pro Sharpeners F600 (#353728088357)
WE’RE SELL ONE OF THE BORIDE T2 Sharpening stones 6x1x1/4"for Edge Pro, TSPRF, KAZAK, Hapstone, Ruixin, etc Sharpeners.
Boride Abrasives T2 stones for Apex Edge Pro, TSPROF, KAZAK, Ruixin, Hapstone, etc.
Stones are152*25*6 mm (6*1*1/4”) size.
Twice the thickness of the original Apex Edge Pro stones!!!
Can be used with oil or water.
This "blue" colored, medium hard, aluminum oxide product is treated with a special resin compound for maximum performance.
High 'dish' resistance.
Available in 8 grit sizes (FEPA-F) - T2 F150 (Abrasive particle size in microns - 80μm.) T2 F220 (Abrasive particle size in microns - 50μm.) T2 F320 (Abrasive particle size in microns - 30μm.) T2 F400 (Abrasive particle size in microns - 18μm.) T2 F600 (Abrasive particle size in microns - 10μm.) T2 F800 (Abrasive particle size in microns - 6.5μm.) T2 F1000 (Abrasive particle size in microns - 4.5μm.) T2 F1200 (Abrasive particle size in microns - 3μm.) Stones are 'ready to use' - flattened and lapped. Each stone is mounted on aluminum plate to fit Edge Pro sharpener. |
T2 Boride for Apex Edge Pro, TSPROF, KAZAK, Ruixin, etc.
Condition is "New". Shipped with USPS First Class and Worldwide by
eBay International Standard Delivery
In case of using the water as lubricant, soak the stone in water for 1-2 minutes. In case of using the oil, put a small amount (1-2 drops) of honing oil on the stone’s surface and spread it evenly over the stone with a finger. If the stone absorbs the honing oil, use largemouth of oil.
The Boride Corp as the Manufacturer says that stones may have the following minor defects (Please, don't complain and blame me, guys):
· Saw strokes on the work surface
· Residues of lacquer
· Small chips at the corners and along the edges (no larger than 1 mm)
All these defects will be eliminated during preparation of the stone for work. Most sharpening stones requires preparation, and Boride stones are no exception. You may to lapping the stones for improve sharpening quality, but this recommendation for professional ONLY – for a kitchen knife you may start to work WHEN it comes from Boride Corp. Boride Corp recommend using loose silicon carbide powder or diamond lapping plate for preparation of the stone for work.